欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3732-1982(2011) Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings《紫外线固化涂料固化时间报告的标准操作规程》.pdf

    • 资源ID:515360       资源大小:63.04KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3732-1982(2011) Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings《紫外线固化涂料固化时间报告的标准操作规程》.pdf

    1、Designation: D3732 82 (Reapproved 2011)Standard Practice forReporting Cure Times of Ultraviolet-Cured Coatings1This standard is issued under the fixed designation D3732; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l

    2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This practice applies to all coatings

    3、cured by ultravioletenergy.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this

    4、 standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D658 Test Method for Abrasion Resistance of OrganicCoatings by Air Blast Abrasive3D968 Test Methods for Abrasion Resistan

    5、ce of OrganicCoatings by Falling AbrasiveD1474 Test Methods for Indentation Hardness of OrganicCoatingsD2197 Test Method for Adhesion of Organic Coatings byScrape AdhesionD2336 Guide for Specifying Factory Applied Wood Coat-ings3D2793 Test Method for Block Resistance of Organic Coat-ings on Wood Pan

    6、el SubstratesD2794 Test Method for Resistance of Organic Coatings tothe Effects of Rapid Deformation (Impact)D3023 Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Re-agentsD3281 Test Method for Formability of Attached OrganicCoatings with Impact-We

    7、dge Bend Apparatus3D3359 Test Methods for Measuring Adhesion by Tape TestD3363 Test Method for Film Hardness by Pencil Test3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 cure, nthe condition of a coating after conversion tothe final state of cure as measured by tests generall

    8、y related toend-use performance and mutually agreeable to supplier andpurchaser.3.1.2 ultraviolet curing, nconversion of a coating from itsapplication state to its final use state by means of a mechanisminitiated by ultraviolet radiation generated by equipment de-signed for that purpose.4. Significa

    9、nce and Use4.1 This practice provides a guide whereby all pertinentvariables relating to the ultraviolet cure of a coating aredescribed.5. Procedure5.1 Apply the coating to be cured to the desired substrate ata film thickness typical to that normally used. After approxi-mately the time delay encount

    10、ered in production pass thecoated substrate through the curing equipment and subse-quently test for cure, as defined in 3.1.1, using the appropriatemethods listed in 5.1.1 through 5.1.11. The most commonlyused test methods are listed in 5.1.1 through 5.1.4.5.1.1 Impact ResistanceTest Method D2794.5.

    11、1.2 Film HardnessTest Method D3363.5.1.3 Solvent Rub TestHold a pad of cheesecloth or othercloth saturated with an agreed-upon solvent, usually methylethyl ketone, over two adjacent fingers using a protectivecovering. Rub the wet pad back and forth across a 100-mmportion of the cured film using vigo

    12、rous pressure, one forwardand one backward movement constituting one double rub. Takethe end point as the number of double rubs required to softenor penetrate the film. Fully cured films are normally required to1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatin

    13、gs, Materials, and Applications and is the direct responsibility ofSubcommittee D01.55 on Factory Applied Coatings on Preformed Products.Current edition approved June 1, 2011. Published June 2011. Originallyapproved in 1978. Last previous edition approved in 2005 as D3732 82 (2005).DOI: 10.1520/D373

    14、2-82R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this histori

    15、cal standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.resist a specified number of rubs and the result of the test isgiven as exceeding the limit or failing the test.5.1.4 SandabilityUltraviolet cu

    16、red fillers are usuallyjudged by their sandability with an agreed-upon grit of paper.This test is often made immediately after the material leavesthe ultraviolet processor.5.1.5 Specifying PropertiesGuide D2336.5.1.6 Abrasion ResistanceTest Methods D658 and D968.5.1.7 Indentation HardnessTest Method

    17、s D1474.5.1.8 AdhesionTest Methods D2197 and D3359.5.1.9 Block ResistanceTest Method D2793.5.1.10 FormabilityTest Method D3281.5.1.11 Stain and Reagent ResistancePractice D3023.5.2 Repeat the application, curing, and testing with freshmaterial on fresh substrates until the shortest time that yields

    18、acured film is obtained.6. Report6.1 Ultraviolet curing equipment is available with severaldesign variables. Therefore, include the following informationwith results where applicable:6.1.1 Number of bulbs,6.1.2 Bulb type (intensity, spectral distribution, composi-tion),6.1.3 Bulb age,6.1.4 Bulb loca

    19、tion (height from work and orientation toworkpiece),6.1.5 Reflector design,6.1.6 Conveyor speed or exposure time to achieve cure,6.1.7 Substrate,6.1.8 Coating identification and age of sample if known,6.1.9 Wet film thickness,6.1.10 Temperature conditions in the curing unit,6.1.11 Curing environment

    20、 (air, nitrogen, or other atmo-sphere),6.1.12 Cure tests used (refer to Section 5), and6.1.13 Age of cured film when tests were run.7. Keywords7.1 cure time; ultraviolet-cured coatingsASTM International takes no position respecting the validity of any patent rights asserted in connection with any it

    21、em mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical com

    22、mittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a

    23、meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Driv

    24、e, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3732 82 (2011)2


    注意事项

    本文(ASTM D3732-1982(2011) Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings《紫外线固化涂料固化时间报告的标准操作规程》.pdf)为本站会员(deputyduring120)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开