欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3499-2011 Standard Test Method for Toughness of Wood-Based Structural Panels《胶合板粘性的标准试验方法》.pdf

    • 资源ID:514891       资源大小:110.82KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3499-2011 Standard Test Method for Toughness of Wood-Based Structural Panels《胶合板粘性的标准试验方法》.pdf

    1、Designation: D3499 11Standard Test Method forToughness of Wood-Based Structural Panels1This standard is issued under the fixed designation D3499; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number i

    2、n parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method for toughness of wood-based structuralpanels

    3、covers the determination of energy necessary to causefailure by impact loading of a beam specimen which is simplysupported and loaded at midspan. Wood-based structural pan-els in use include plywood, waferboard, oriented strand board,and composites of veneer and of wood-based layers.1.2 The values s

    4、tated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its

    5、use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D143 Test Methods for Small Clear Specimens of TimberD2395 Test Methods f

    6、or Specific Gravity of Wood andWood-Based MaterialsD4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Base Materials3. Significance and Use3.1 The failure of wood-based materials with impact loadsis sometimes an important criteria in design considerations. Inaddition, some

    7、effects on the mechanical properties of wood,such as decay, are best evaluated by measuring its toughness.This test method serves to evaluate the toughness of structuralpanel products while Methods D143 can be used to measurethe toughness of solid clear wood specimens.4. Apparatus4.1 The toughness t

    8、esting machine (Note 1) shall consist ofa frame supporting a pendulum, being so arranged that ameasured amount of the energy from the fall of the pendulummay be applied to a test specimen. The pendulum shall consistof a bar to which is fastened a weight adjustable to differentpositions and shall car

    9、ry at its upper end a drum or pulleywhose center provides the axis of rotation. The force shall beapplied to the specimen by means of a flexible steel cablepassing over the drum. A stationary graduated scale or dial anda vernier operated by the moving drum shall be provided forreading the angles thr

    10、ough which the pendulum swings. Themachine shall be adjusted before test so that the pendulumhangs truly vertical and adjusted to correct for friction. Thecable shall be adjusted so that the load is applied to thespecimen when the pendulum swings to within approximately15 of the vertical so as to pr

    11、oduce complete failure by the timethe downward swing is completed.NOTE 1The set-up shown in Fig. 1 has been found to give satisfactoryresults.5. Test Specimen5.1 The toughness test specimen to be used in conjunctionwith the Forest Products Laboratory toughness testing machineshall be58 in. (16 mm) i

    12、n width for material less than58 in. (16mm) in thickness, and the thickness of the specimen shall beequal to that of the material. For material more than58 in. (16mm) in thickness, the width shall be equal to the thickness ofthe material, thus making the specimen square in cross section.The length s

    13、hall be determined from the thickness of thematerial in accordance with Table 1. The actual cross-sectionaldimensions, and the specimen and span length shall be mea-sured to an accuracy of not less than 60.3 % or 0.001 in. (0.02mm) whichever is larger.6. Control of Moisture6.1 Panel specimens to be

    14、tested at specific moisture con-tents or after reaching equilibrium moisture content at specifictemperature and relative humidity conditions shall be condi-tioned to approximate constant weight in controlled atmo-spheric conditions. For approximating moisture conditions of1This test method is under

    15、the jurisdiction of ASTM Committee D07 on Woodand is the direct responsibility of Subcommittee D07.03 on Panel Products.Current edition approved May 1, 2011. Published June 2011. Originallyapproved in 1976. Last previous edition approved in 2000 as D3499 94 (2005).DOI: 10.1520/D3499-11.2For referenc

    16、ed ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co

    17、nshohocken, PA 19428-2959, United States.panels used under dry conditions, a relative humidity of 65 62 % at a temperature of 68 6 6F (20 6 3C) is recommended.7. Span and Supports7.1 The test specimen shall be supported as a beam on twovertical pins, which exert reactions that are perpendicular to t

    18、heplane of the panels or laminations. These pins shall be adjustedto the span length taken from Table 1 which provides for aspecimen overhang of 1 in. (25 mm) at each end.8. Loading Procedure8.1 Apply the load at the center of the span perpendicular tothe plane of the plies. Apply the load through a

    19、 tup, attached toa flexible cable, having a radius of curvature approximatelyequal to one and one-half times the depth of the test specimen.Choose the weight position and initial angle of the pendulumso that complete failure of the specimen is obtained on onedrop. Most satisfactory results are obtai

    20、ned when the differencebetween the initial and final angle is at least 10.NOTE 2In order to satisfy these conditions properly, it will benecessary to use a toughness testing machine of proper capacity for thespecimens being tested. The larger size specimens can be tested in thelarge size Forest Prod

    21、ucts Laboratory toughness machine which has amaximum capacity of 673 inlbf (76 J), while tests of smaller specimenscan be made in the 20 inlbf (2.3 J), capacity intermediate size machine.9. Calculation9.1 Read the initial and final angle to the nearest 0.2 bymeans of the attached vernier. Calculate

    22、the toughness asfollows:T 5 wL cos A22 cos A1! (1)where:T = toughness (work per specimen), inlbf (or J),w = weight of the pendulum, lbf (or kgf),L = distance from the center of the supporting axis to thecenter of gravity of the pendulum, in. (or mm),A1= initial angle (Note 3), deg, andA2= final angl

    23、e the pendulum makes with the verticalafter failure of the test specimen, deg.NOTE 3Since friction is compensated for in the machine adjustment,the initial angle may be regarded as exactly 30, 45, or 60, as the case maybe.10. Moisture Content and Specific Gravity10.1 Moisture ContentCut a moisture c

    24、ontent samplewhich is full width and at least 1 in. (25 mm) in length from thespecimen and weigh immediately after each test. If inspectionof the edges of a plywood specimen reveals the presence of aknot in any of the inner plies, select a second sample. Moisturecontent samples also serving as speci

    25、fic gravity samples shallbe free of voids. Moisture content determinations shall bemade in accordance with Test Method D4442.10.2 Specific GravityDetermine the specific gravity inaccordance with Test Methods D2395. The specimen may bethe same as that for moisture content determination but musthave v

    26、olume of at least 0.2 in.3(3 cm3), and be free of visibleknots or voids.11. Report11.1 The specimen shall be described as to species, con-struction, and adhesive type used in its manufacture.FIG. 1 Toughness Test of Structural Panel Showing Load Applied to Specimen When Pendulum is Approximately 15

    27、from the VerticalTABLE 1 Length of Toughness Test SpecimensPanel Thickness, in. (mm)Span Length Specimen Lengthin. mm in. mmup to18 (3), incl 2 50 4 100Over18 (3) to14 (6), incl 3 75 5 125Over14 (6) to38 (9), incl 5 125 7 175Over38 (9) to12 (12), incl 6 150 8 200Over12 (12) to58 (16), incl 8 200 10

    28、250Over58 (16) to34 (18), incl 9 230 11 275Over34 (18) to 1 (25), incl 12 300 14 350D3499 11211.2 Data for individual specimens and specimen averagesshall include:11.2.1 Specimen thickness,11.2.2 Length,11.2.3 Span length,11.2.4 Moisture content,11.2.5 Specific gravity, and11.2.6 Toughness (work per

    29、 specimen), inlbf (or J).12. Precision and Bias12.1 The precision and bias of this test method have not yetbeen determined, but when data are available, a precision andbias statement will be included.13. Keywords13.1 plywood; structural panels; toughness; woodASTM International takes no position res

    30、pecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This

    31、standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Intern

    32、ational Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown be

    33、low.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3499 113


    注意事项

    本文(ASTM D3499-2011 Standard Test Method for Toughness of Wood-Based Structural Panels《胶合板粘性的标准试验方法》.pdf)为本站会员(jobexamine331)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开