欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3495-2010 Standard Test Method for Hexane Extraction of Leather《皮革制品中己烷萃取的标准试验方法》.pdf

    • 资源ID:514884       资源大小:61.81KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3495-2010 Standard Test Method for Hexane Extraction of Leather《皮革制品中己烷萃取的标准试验方法》.pdf

    1、Designation: D3495 10Standard Test Method forHexane Extraction of Leather1This standard is issued under the fixed designation D3495; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses

    2、 indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method covers the quantitative extraction of alltypes of leather

    3、with hexane. This test method does not applyto wet blue.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is therespo

    4、nsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D2813 Practice for Sampling Leather for Physical andChemical TestsD3790 Test Method for Vola

    5、tile Matter (Moisture) ofLeather by Oven Drying3. Significance and Use3.1 This test method measures the amount of hexane-soluble lubricant present in all types of leather. Adequatelubrication prevents abrasion of leather fibers during flexing.This lubrication is generally obtained from the fat liquo

    6、r addedat the tannery. Some lubrication is also obtained from naturalgrease produced during the life of the animal.4. Apparatus4.1 Analytical Balance.4.2 Soxhlet Apparatus, consisting of a boiling flask, extrac-tion tube, and condenser.4.3 Forced Circulating Air Oven, capable of maintaining thespeci

    7、fied temperature.4.4 Electric Hot Plate.4.5 Extraction Thimbles, fat-free, cellulose, Alundum, orfritted.4.6 Absorbent Cotton, fat-free.4.7 Steam Bath.5. Reagent5.1 Hexane, ACS Reagent Grade conforming to the follow-ing requirements:5.1.1 Color (APHA)10 max.5.1.2 Density (g/mL) at 25C0.687 max.5.1.3

    8、 Boiling Range1 to 95 mL, not more than 4.0C.5.1.4 Residue After Evaporation0.001 % max.5.1.5 Acidity (as CH3COOH)To pass test (limit 0.002 %).5.1.6 Sulfur Compounds (as S)0.005 % max.5.1.7 ThiopheneTo pass test.NOTE 1This reagent grade hexane is generally a mixture of severalisomers of hexane (C6H1

    9、4), predominantly n-hexane and methylcyclopen-tane (C6H12).6. Test Specimens6.1 The leather shall be sampled in accordance with MethodD2813. Leather test specimens shall be obtained from thecomposite sample prepared by random sampling, cutting, andmixing equal portions of leather representing the lo

    10、t that isbeing analyzed. The well-mixed leather pieces shall be groundin a mill (Wiley or equal) having a No. 5 (4-mm) sieve. Theground leather that passes through this 4-mm sieve shall bemixed well and used as the composite sample.7. Procedure7.1 Determine the moisture content of the composite samp

    11、lefrom which the ground leather for hexane extraction is taken inaccordance with Test Method D3790. Determine the weight ofthe ground leather taken from the composite sample for1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommitte

    12、e D31.06 on Chemical Analysis.Current edition approved Nov. 1, 2010. Published December 2010. Originallyapproved in 1976. Last previous edition approved in 2006 as D3495 00(2006).DOI: 10.1520/D3495-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Servi

    13、ce at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.moisture content at the same time and under t

    14、he same ambientconditions as the weight of the ground leather taken for hexaneextraction.7.2 Weigh5gofground leather taken from the composite tothe nearest 0.001 g and record this value as W1. Loosely packthis material in an appropriately sized extraction thimble andcover with a pad of fat-free cott

    15、on. Place the loaded thimble inthe Soxhlet extraction tube. Dry an extraction flask in an ovenfor1hat1006 2C, cool in a desiccator, and weigh to thenearest 0.001 g. Record this value as W2. Fill the flaskapproximately two-thirds full with hexane, assemble the appa-ratus, circulate the water through

    16、the condenser, and heat theflask until the extraction of the leather has continued for aminimum of 50 cycles. If the Soxhlet drips continuouslyinstead of cycling, extract the leather for a minimum of 5 husing maximum heat. At the end of the extraction period,remove the flask containing the extractio

    17、n solvent and drive offthe hexane. When 10 to 20 mL of hexane remain, heat gentlyon a steam bath until the odor of the solvent can no longer bedetected. Facilitate the removal of the hexane by utilizing avacuum or a gentle stream of filtered (oil- and water-free) air.After the hexane has been remove

    18、d, dry the flask containingthe extracted matter in a forced circulating air oven at 100 62C, for 2 h, cool to room temperature in a desiccator andweigh. Continue drying for successive 2-h periods until con-stant weight is obtained. When successive weighings vary byless than 6 0.005 g, consider the w

    19、eight constant. Record thisweight to the nearest 0.001 g as W3. No more than threesuccessive 2-h drying periods shall be allowed. If constantweight has not been obtained after the third drying, the resultsof the second drying period shall be reported.8. Calculation8.1 Calculate the percentage of hex

    20、ane-soluble matter, on amoisture-free basis, as follows:Hexane2soluble matter, % 5W32 W2W13100 2 % moisture!1003 100(1)where:W1= original weight of extracted leather,W2= weight of extraction flask, andW3= weight of extraction flask and hexane-soluble matter.9. Report9.1 Report the hexane-soluble mat

    21、ter in the leather as theaverage value obtained from the test results to nearest 0.01 %.9.2 State that the results are calculated on a moisture-freebasis.10. Precision and Bias10.1 Interlaboratory Test Data3An interlaboratory testwas run in 1972 in which each of 7 laboratories tested duplicatespecim

    22、ens from each of 15 different types of leather. Alllaboratories tested the following leathers: chamois, yellowlace, crust sheepskin, crust goatskin, vegetable-strap leather,chrome-retan side leather, vegetable-skirting leather,vegetable-retan side leather, latigo-lace leather, white-laceleather, sue

    23、de sheepskin, horsehide (finished), white-sideleather, chrome-split leather, and silicone-treated militaryleather. The components of variance for hexane-soluble matterexpressed as standard deviations were calculated to be:Within2laboratory single operator!component0.14 percentage points (2)Between2l

    24、aboratory component0.41 percentage points (3)10.2 PrecisionFor the components of variance reported in9.1, two averages of two observations each of hexane solublematter should be considered significantly different at the 95 %probability level if the difference equals or exceeds thefollowing critical

    25、differences:Within2laboratory single operator! precision 0.59 percentage points(4)Between2laboratory precision 1.41 percentage points see Note3!(5)NOTE 2The critical differences were calculated using t = 1.960,which is based on infinite degrees of freedom.NOTE 3The calculated values of the critical

    26、differences should beconsidered to be a general statement particularly with respect to between-laboratory precision. Before a meaningful statement can be made abouttwo specific laboratories, the amount of statistical bias, if any, betweenthem must be established, with each comparison being based on

    27、recentdata obtained on randomized specimens from one sample of the materialto be tested. The interlaboratory test showed that for certain leatherscontaining more than 18 % hexane-soluble matter the between-laboratorycritical difference could be as high as 3 percentage points.10.3 BiasNo justifiable

    28、statement on bias can be made,since the true value of hexane-soluble matter cannot beestablished by an accepted reference method.11. Keywords11.1 extractables; extraction; fat liquor; hexanesolublelubricant; lubrication3Supporting data have been filed atASTM Headquarters and may be obtained byreques

    29、ting Research Report RR: D-31-1003.D3495 102ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and

    30、 the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revisio

    31、n of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you sho

    32、uldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3495 103


    注意事项

    本文(ASTM D3495-2010 Standard Test Method for Hexane Extraction of Leather《皮革制品中己烷萃取的标准试验方法》.pdf)为本站会员(cleanass300)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开