欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3070-2018 Standard Practice for Rapid Pressure Determination of Pressurized Products.pdf

    • 资源ID:514045       资源大小:73.48KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3070-2018 Standard Practice for Rapid Pressure Determination of Pressurized Products.pdf

    1、Designation: D3070 00 (Reapproved 2010)D3070 18Standard Test Method ofPractice forRapid Pressure Determination of Pressurized Products1This standard is issued under the fixed designation D3070; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

    2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method practice covers rapid pressure determination for pressurized products.1.2 The

    3、values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associate

    4、d with its use. It is the responsibilityof whoever uses the user of this standard to consult and establish appropriate safety safety, health, and healthenvironmentalpractices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor

    5、dance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Significance and Use2.1 This te

    6、st method practice is a rapid technique for quality control, formula development, etc., where speed is necessary anda high degree of accuracy is not essential.3. Apparatus3.1 Pressure Gage, stainless steel construction, with a range from 0 to 160 psi (0 to 1.1 MPa), and preferably with one numbergra

    7、duations. The gage should be attached to a 18-in. Hoke needle valve, with all of the connections leak proof. Attach an adaptorto the needle valve to fit the aerosol valves on the cans to be tested (Fig. 1).NOTE 1Take care that there are no leaks in the gage apparatus. This can be checked by occasion

    8、ally making a measurement with the attachment underwater.3.1.1 Care should be taken to clean the gage daily by repeated injection and venting of an approved cleaning solution containinga bacteriastat. After cleaning, rinse the gage and apparatus with clean water and purge them with the prepressurizi

    9、ng gas prior touse.3.1.2 For nonfood products, the gage apparatus may be cleaned between product uses by forcing suitable solvents into the gage,then venting it. This should be repeated several times until the gage is free of contamination.NOTE 2When changing from chlorinated solvents to water-base

    10、products, and vice versa, the above is particularly important to avoid possiblecontamination.3.1.3 Use a separate gage apparatus for food products only.3.2 Water Bath, constant-temperature, accurate to at least 61F (60.5C).4. Reagents4.1 Pressurizing Gas:4.1.1 For nonfood products the following are

    11、recommended:4.1.1.1 Carbon Dioxide (CO2).4.1.1.2 Compressed Air. Compressed Air.4.1.1.3 Nitrogen (N2).4.1.2 For food products the following are recommended:1 This test method practice is under the jurisdiction of ASTM Committee D10 on Packaging and is the direct responsibility of Subcommittee D10.33

    12、 on MechanicalDispensersAerosol Products. Originally developed by the Chemical Specialties Manufacturers Assn.Current edition approved Oct. 1, 2010May 1, 2018. Published November 2010June 2018. Originally approved in 1972. Last previous edition approved in 20052010 asD3070 00 (2010). (2005). DOI: 10

    13、.1520/D3070-00R10.10.1520/D3070-18.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM reco

    14、mmends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.2.1 Carbo

    15、n Dioxide (CO2).4.1.2.2 Nitrogen (N2).4.1.2.3 Nitrous Oxide (N2O).NOTE 3Suitable pressurizing gases for food products should be limited to those that are not liquefiable at the temperatures and pressures used.Compressed air is not recommended because of its oxygen content.5. Sampling5.1 Normal produ

    16、ction or laboratory samples shall be used for this test.6. Calibration6.1 A suitable standard check, accurate to 60.5 psi (3.4 kPa), should be set up in the laboratory for quick calibration of the testgage.6.2 Gages in constant use should be checked approximately once each week, or at any time after

    17、 the gage has been subjectedto accidental shock, such as dropping.7. Procedure7.1 Immerse the can in the constant-temperature water bath. The immersion time required depends on the initial cantemperature. If the can temperature is roughly within 610F (65.5C) of the bath temperature, immerse the can

    18、for 15 min,agitating it every 5 min. For water base products having higher specific heat, large cans (over 12 oz (30 cm3), or cans varyingwidely in temperature, immerse for at least 45 min (preferably 60 min).NOTE 4Care should be taken to avoid handling the cans with bare hands after they have reach

    19、ed constant temperature, since the pressure is a functionof the can temperature.7.2 Prepressurize the gage as nearly as possible to the anticipated can pressure.7.3 Agitate the can and attach the gage to the valve on the can, press it open, and open the Hoke valve.NOTE 5“Bleeding” or removal of gas

    20、from the vapor phase before checking the pressure is not permissible if the true pressure in the can is desired.7.4 Record the reading and exact bath temperature.FIG. 1 Pressure Gage ApparatusD3070 1827.5 Close and remove the Hoke valve.7.6 Repeat 7.1 7.6 twice again, and average the results.8. Repo

    21、rt8.1 Report the following information:8.1.1 Product being tested,8.1.2 Exact bath temperature,8.1.3 Results of the three pressure readings, and8.1.4 Average of the three pressure readings.9. Precision and Bias9.1 PrecisionThe precision of Test Method Practice D3070 is highly dependent on the conten

    22、ts being tested. One laboratoryhas investigated two products with three replicate tests, yielding the following results:Product A Can Pressure (psig)Can #1 56Can #2 55Can #3 55Mean value 55.3Standard deviation 0.6Product B Can Pressure (psig)Can #1 59Can #2 59Can #3 60Mean value 59.3Standard deviati

    23、on 0.69.1.1 Both groups of test samples had been conditioned in a water bath of 70.5F prior to testing.9.1.2 Other products in aerosol packages may have values different than the values disclosed in 9.1. The results of this test aredependent on variations in filling, the contents both propellent and

    24、 concentrate, the partial pressures of the propellent used, thehead space in the particular can, as well as the level of the product in the can at the time of testing. Users of this test method practiceare suggested to reference historical files of previous tests of similar aerosol packaging content

    25、s for an estimate ofwithin-laboratory repeatability. The Committee believes that because of this strong product and component material dependency,further investigation of repeatability and reproducibility is not practicable.9.2 BiasTest Method Practice D3070 has no bias because an accepted reference

    26、 or referee value is not available.10. Keywords10.1 aerosol can pressure; aerosol packaging; pressurized productsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advi

    27、sed that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either

    28、reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If

    29、you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individu

    30、al reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 183


    注意事项

    本文(ASTM D3070-2018 Standard Practice for Rapid Pressure Determination of Pressurized Products.pdf)为本站会员(syndromehi216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开