欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D2949-2001a(2008)e1 Standard Specification for 3 25-in Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings《外径3 25 in的聚化乙烯(PVC)塑料排水 排污管和配.pdf

    • 资源ID:513836       资源大小:159.84KB        全文页数:9页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D2949-2001a(2008)e1 Standard Specification for 3 25-in Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings《外径3 25 in的聚化乙烯(PVC)塑料排水 排污管和配.pdf

    1、Designation: D2949 01a (Reapproved 2008)1An American National StandardStandard Specification for3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) PlasticDrain, Waste, and Vent Pipe and Fittings1This standard is issued under the fixed designation D2949; the number immediately following the designa

    2、tion indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by ag

    3、encies of the Department of Defense.1NOTE6.6 was editorially corrected in March 2010.1. Scope1.1 This specification covers requirements and test methodsfor materials, dimensions and tolerances, deflection load, crushresistance, hydrostatic-burst resistance, flattening resistance,impact resistance, a

    4、nd solvent cement. A form of marking isalso included. Plastic which does not meet the materialrequirements specified in Section 5 is excluded.NOTE 1This specification was formerly issued under the title, 3-in.ThinWall Poly(Vinyl Chloride) (PVC) Plastic Drain,Waste, andVent Pipeand Fittings.NOTE 2Tec

    5、hniques for making solvent-cement joints are given inPractice D2855.1.2 The text of this specification references notes, footnotes,and appendixes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of the specifi

    6、cation.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 The following precautionary caveat pertains only to thetest methods portio

    7、n, Section 7, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tion

    8、s prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating toPlasticsD1784 Specification for Rigid

    9、Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride) (PVC) Pipe and Molded Fittings byAcetone ImmersionD2412 Tes

    10、t Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup (Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride) (PV

    11、C) Plastic Piping SystemsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride) (PVC) Pipe and FittingsD3311 Specification for Drain, Waste, and Vent (DWV)Plastic Fittings PatternsF402 Practice for Safe Handling of Solvent Cements, Prim-ers, and Cleaners Used for Joining Thermopl

    12、astic Pipe andFittingsF412 Terminology Relating to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for Ther-moplastic Pipe and Fittings3. Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412, and abbreviations are in accordance with Termi-nology D1600, u

    13、nless otherwise specified.4. Significance and Use4.1 The requirements of this specification are intended toprovide pipe and fittings suitable for drainage of sewage andcertain other liquid wastes where toughness, resistance to1This specification is under the jurisdiction of ASTM Committee F17 on Pla

    14、sticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Nov. 1, 2008. Published February 2009. Originallyapproved in 1971. Last previous edition approved in 2001 as D2949 01a1. DOI:10.1520/D2949-01AR08.2For referenced ASTM standards, visit the ASTM

    15、website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United

    16、States.deterioration from water and chemicals, flattening and agingresistance, and strong tight joints are required.4.2 When joining 3.25-in. outside diameter PVC DWVpiping to 3-in. Schedule 40 PVC DWV piping, it is necessaryto use either reducer bushings or increasers, as shown in thetables at the

    17、end of the text, due to the differences in pipeoutside diameters.NOTE 3Industrial waste disposal lines should be installed only withthe specific approval of the cognizant building code authority sincechemicals not commonly found in drains and sewers, and temperatures inexcess of 160F (70C), may be e

    18、ncountered.5. Materials5.1 Basic MaterialsPipe and fittings shall be made fromvirgin poly (vinyl chloride) compounds meeting the require-ments of Class 12454, as defined and described in SpecificationD1784.5.2 Rework MaterialThe manufacturer shall use only hisown clean pipe or fitting rework materia

    19、l and the pipe or fittingproduced shall meet all the requirements of this specification.5.3 Solvent CementThe solvent cement shall meet therequirements of Specification D2564.6. Requirements6.1 GeneralThe pipe and fittings shall be homogeneousthroughout and free of visible cracks, holes, foreign inc

    20、lusions,or other injurious defects. The pipe shall be as uniform ascommercially practicable in color, opacity, density, and otherphysical properties.6.1.1 The requirements in this section are intended only foruse as quality control tests, not as simulated service tests.6.2 Dimensions and TolerancesA

    21、ll dimensions shall bemeasured in accordance with Test Method D2122. All toler-ances shall meet the requirements of Tables 1-11 unlessotherwise specified.6.2.1 Pipe:6.2.1.1 Pipe DimensionsThe outside diameters and wallthicknesses of the pipe shall meet the requirements of Table 1.6.2.1.2 Pipe Length

    22、The pipe shall be in either 10 or 20-ftor 3 or 6-m lengths, unless otherwise specified with allowabletolerance of +12 in., 0 in. or +13 mm, 0 mm.6.2.2 Fittings:6.2.2.1 Fittings-Socket DimensionsThe socket dimen-sions of fittings shall meet the requirements given in Table 2.6.2.2.2 Fittings Laying Le

    23、ngth DimensionsThe layinglength dimensions of fittings, shall conform to the requirementsgiven in Table 3 through Tables 11.6.2.2.3 Transition AdaptersThe dimensions of adaptersfor connecting plastic pipe to cast iron hubs shall conform tothe dimensions given in Table 4.6.2.2.4 Fittings DimensionsTh

    24、e dimensions of fittingscovered by this specification shall meet the requirements givenin Table 3 through Table 11.NOTE 4Additional fittings in IPS dimensions are included in Speci-fication D3311.6.3 Deflection Load and Crush Resistance:6.3.1 PipeThe pipe shall support a minimum load of 600lbf/linea

    25、r ft (810 N/m) at 15 % deflection of the originaldiameter (deflection load), and shall deflect 60 % of theoriginal diameter (crush resistance) without cracking, rupture,or other visible evidence of failure when tested in accordancewith 7.4. The minimum pipe stiffness at 5 % deflection shall be115 lb

    26、f/in.in. (800 kPa).6.3.2 FittingsIndividual fittings unassembled shall with-stand a minimum load of 1000 lbf/ft (1350 N/m) of centerlinelength without cracking or other visible evidence of failurewhen tested in accordance with 7.4. This requirement does notapply to inline fittings.6.4 Minimum Hydros

    27、tatic Burst PressureWhen tested at73F (23C) in accordance with 7.5, the minimum burstpressure of pipe shall be 500 psi (3.45 MPa) and the minimumburst pressure of fittings shall be 200 psi (1.38 MPa).NOTE 5The minimum burst pressure for fittings are lower than thatfor pipe because the geometry is su

    28、ch, particularly area and radii, that thestresses produced in the wall of the fitting are higher than those producedin pipe tested at the same internal pressures. This requirement is intendedonly for the purpose of quality control to ensure that the pipe and fittingshave no weak areas, particularly

    29、at flow and weld lines.6.5 Flattening ResistanceThe average decrease in insidediameters of pipe and fittings shall not exceed 10 % whentested in accordance with 7.6 (Note 3).6.6 Impact ResistanceThe minimum impact resistance,when tested at the time of manufacture, shall be 50 ftlbf (67.79J) at 73F (

    30、23C) for pipe and 20 ftlbf (27.12 J) at 73F forfittings. Test in accordance with Test Method D2444 using TupC and Holder A for pipe and Tup A and Holder B for fittings.Use a 12-lb (5-kg) tup for testing pipe and fittings. Testcouplings cemented to short pieces of pipe and allowed to dryfor 24 h.6.6.

    31、1 Test 10 specimens. When 9 or 10 specimens pass,accept the lot. When 2 or more specimens fail, test 10additional specimens. When 17 of 20 specimens tested pass,accept the lot. When 4 or more of 20 specimens fail, test 20additional specimens. When 32 of 40 specimens pass, acceptthe lot. When 9 or mo

    32、re of 40 specimens fail, the lot does notmeet the requirements of this specification.6.6.2 Failure of the test specimen shall be shattering or anycrack or break extending entirely through the pipe wall andvisible to the unaided eye.TABLE 1 Dimensions and Tolerances for Outside Diameters and Thicknes

    33、ses of PVC 3.25-in. Outside Diameter Plastic Drain, Waste,and Vent Pipe, in. (mm)NominalPipe Size,in.Outside Diameter Wall ThicknessAAverageTolerance onAverageOut-of-Roundness(maximum minus minimum)Min Tolerance3.25 3.250 (82.56) 60.008 (60.20) 0.030 (0.76) 0.125 (3.18) +0.020 (+0.50)AThe minimum is

    34、 the lowest wall thickness of the pipe at any cross section. The maximum permitted wall thickness, at any cross section, is the minimum wall thicknessplus the stated tolerance.D2949 01a (2008)12TABLE 2 Dimensions and Tolerances for Fitting Sockets for 3.25-in. Outside Diameter PVC Plastic Drain, Was

    35、te, and Vent PipeFittings, in. (mm)NOTE 1Spigot ends shall conform to the outside diameters and tolerances for pipe of the same sizeNominalPipe Size,in.ASocket Entrance DiameterBSocket Bottom DiameterCSpigot andSocket DepthDWall ThicknessavgATmBavgCTmBmin minD,E3.25 3.265 (82.94) 60.008 (60.20) 3.24

    36、5 (82.42) 60.008 (60.20) 112 (38) 0.140 (3.56)AThe tolerances on this average are +0.010 to 0.005 in. (+0.25 to 0.13 mm).BTm = permissible deviation of diameter from measured average, often called out-of-roundness.CTolerance on average +0.005 in., 0.010 in. (+0.13 mm, 0.25 mm).DMinimum wall thicknes

    37、s in the socket is 0.125 in.EThe wall thickness is a minimum value except that a 610 % variation resulting from core shift is allowable. In such a case, the average of the two opposite wallthicknesses shall equal or exceed the value shown in the table.TABLE 3 3.25-in. Outside Diameter Bends, in. (mm

    38、)Nominal PipeSize, in.14 Bend G,minLong-Sweep14Bend G,min18 Bend J,min16 Bend J,min116 Bend J,min3.25 278 (73) 4 (101.6) 1 (25.4) 114 (31.8)58 (15.88)TABLE 4 3.25-in. Outside Diameter Reducing Spigots, in. (mm)Nominal Pipe Size, in. L2,min L1,min L3,minMAJ, Nominalmax min3.25 by 4-in.Cast Iron378 (9

    39、8.4) 558 (142.9)38 (9.5) 4916 (115.9) 412 (114.3) 378 (98.4)D2949 01a (2008)136.7 ThreadsFor all fittings having taper pipe threads,threads shall conform to Specification F1498 and be gaged inaccordance with 7.7.6.8 Extrusion QualityThe pipe shall not flake or disinte-grate when tested in accordance

    40、 with Test Method D2152.7. Test Methods7.1 SamplingTake a random sample from each lot orshipment of the pipe and fittings sufficient to determineconformance with this specification.About 40 ft (12 m) of pipeare required to make the tests prescribed. The number offittings required varies depending on

    41、 the size and type offitting.7.2 Conditioning7.2.1 For referee testing at 73F, condition the specimensprior to test at 73.4 6 3.6F (23 6 2C) and 50 6 5 % relativehumidity in accordance with Practice D618, Procedure A.7.2.2 For routine quality control testing at 73F, conditionthe specimens at the tem

    42、perature and humidity of the manu-facturers testing facility for not less than1horuntil thespecimens are at the room temperature.7.3 Test Conditions7.3.1 For referee purposes, conduct tests in the standardlaboratory atmosphere of 73.4 6 3.6F (23 6 2C) and 50 65 % relative humidity.7.3.2 For routine

    43、quality control testing, conduct tests at thetemperature and humidity of the manufacturers testing area.7.4 Deflection Load and Crush ResistanceMeasure thedeflection load and crush resistance of pipe and fittings inaccordance with Test Method D2412. In the test for pipe notethe load when the initial

    44、 inside diameter is reduced by 5 %(pipe stiffness), by 15 % (deflection load), and continue the testuntil the diameter is reduced by 60 % of its original value(crush resistance). The rate of head approach shall be 0.20 to0.25 in./min (5.1 to 6.4 mm/min). Each specimen shall meetthe requirements of 6

    45、.3.1.7.4.1 Fitting Test SpecimensTest three complete fittings.Shim fittings to give full centerline contact with platens.Fittings having nonuniform diameters such as reducers shall beconsidered acceptable when the wall thickness at all points isequal to or greater than the wall thickness of pipe of

    46、the samematerial and diameter that meets the crush resistance require-ments. Each specimen shall meet the requirements of 6.3.2.7.4.2 ProcedureTerminate the test when the inside diam-eter of pipe test specimens is reduced to 40 % of its originalvalue or the pipe cracks or shows other visible evidenc

    47、e offailure. Terminate the test on fittings when the load reaches1000 lbf/ft (1350 N/m) of centerline length. Observe the loadand deflection at the first evidence of cracking, if any. Recordlocation and type of failure.7.4.3 CalculationFor pipe, divide the load in pounds-force or newtons at 15 % def

    48、lection (deflection load) and alsoat failure (crush resistance), if such occurred, by the length ofthe pipe test specimen in feet or metres to obtain the deflectionload and crush resistance, respectively, in pounds per linearfoot, or newtons per metre. For pipe stiffness, divide the loadin pounds-fo

    49、rce or newtons at 5 % deflection by the specimenlength in inches or metres and then divide by the deflection ininches or metres. Calculate the values for each specimenseparately. Examine the test results for each specimen forconformance to the requirements of 6.3.1 and 6.3.2.TABLE 5 3.25-in. Outside Diameter Reducing Sanitary Tee and 45 Wyes, in. (mm)Nominal Pipe Size, in.Sanitary Tee Reducing 45 Wye Reducing Single and DoubleG1,min G2,min G3,min G1,min G2,min G3,min3.25 by 3.25 by112-in. IPS1516 (23.8


    注意事项

    本文(ASTM D2949-2001a(2008)e1 Standard Specification for 3 25-in Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings《外径3 25 in的聚化乙烯(PVC)塑料排水 排污管和配.pdf)为本站会员(赵齐羽)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开