欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D2835-1989(2003) Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements《混凝土铺面用预制压缩密封物安装用润滑剂的标准规范》.pdf

    • 资源ID:513591       资源大小:26.68KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D2835-1989(2003) Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements《混凝土铺面用预制压缩密封物安装用润滑剂的标准规范》.pdf

    1、Designation: D 2835 89 (Reapproved 2003)Standard Specification forLubricant for Installation of Preformed Compression Sealsin Concrete Pavements1This standard is issued under the fixed designation D 2835; the number immediately following the designation indicates the year oforiginal adoption or, in

    2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 T

    3、his specification covers a lubricant suitable for facili-tating the insertion and positioning of preformed elastomericcompression seals in prepared voids (usually contractionjoints) in concrete pavement. For changes to this Standardsince the last issue, refer to the Summary of Changes Sectionat the

    4、end of the Standard.1.2 The requirements of the lubricant are based on theperformance of the lubricant as measured by its solids content,homogeneity, consistency and drying rate.1.3 The values stated in inch-pound units are to be regardedas the standard. The metric equivalents of U.S customary units

    5、may be approximate.1.4 The following precautionary caveat pertains only to thetest method portion, Section 7 of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish a

    6、ppropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1084 Test Methods for Viscosity of AdhesivesD 1644 Test Methods for Nonvolatile Content of Varnishes3. Classification3.1 The lubricant shall be b

    7、ased on polychloroprene, con-taining only soluble phenolic resins blended together withantioxidants and acid acceptors in a suitable mixture of organicsolvents.4. Requirements4.1 Homogeneity The lubricant shall be uniform andcontain no lumps or agglomerates.4.2 Solids Content The nonvolatile content

    8、 of the lubri-cant shall be no less than 24.0 weight %.4.3 Consistency The lubricant shall exhibit a viscosity inone of the following ranges:4.3.1 Type Ifor hand or machine application, 3000 to8000 cP.4.3.2 Type IIfor machine application, 8000 to 15 000 cP.4.4 Drying Rate A bond between lubricant-co

    9、ated papersprepared after 8-min drying time shall separate completely inless than 10 s when a 50-g load is applied in shear. A similarbond prepared after 20-min drying time shall remain unsepa-rated for a minimum of 10 s when a 50-g load is applied inshear.5. Basis of Purchase5.1 Each lot of lubrica

    10、nt shall be accompanied by themanufacturers certified test results attesting compliance withthis specification, unless an alternative agreement is concludedby the manufacturer and the purchaser.6. Sampling6.1 The lubricant samples shall be a 1-quart (1-litre) aliquotconsisting of a composite taken w

    11、hen possible from three ormore separate containers chosen at random. Samples also shallbe taken from containers which appear to be nonrepresentativeand shall be tested separately. Before a sample is withdrawn,the contents in the container shall be mixed to uniformconsistency. The sample shall be pla

    12、ced immediately in anairtight-glass jar or metal can until tested.7. Test Methods7.1 Homogeneity Stir the test sample by hand for 2 minwith a spatula. Withdraw the spatula and examine the lubricantas it flows from the spatula for lumps or agglomerates.Particles smaller in diameter than 0.015 in. (0.

    13、38 mm) shall notbe considered cause for rejection.1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.34 onPreformed Joint Fillers, Sealers, and Sealing Systems.Current edition approved Oct. 27, 1989. Pu

    14、blished March 1990. Originallyapproved in 1969. Last previous edition approved in 1998 as D 2835 89 (1998).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stand

    15、ards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTE 1At the consumers request, compliance with the 0.015-in.(0.38-mm) re

    16、quirement shall be determined by a sample diluted 1 + 4 withXylene through a 40-mesh sieve.7.2 Solids Content Determine in accordance with MethodA of Test Methods D 1644.7.3 Consistency Determine in accordance with Method Bof Test Methods D 1084. Use a No. 4 spindle at 20 rpm at a testtemperature of

    17、 77 6 0.9F (25 6 0.5C).7.4 Drying Rate:7.4.1 Apparatus:7.4.1.1 Film Applicator3, 2-in. (50-mm) wide, 5 to 25-mils(0.127 to 0.635-mm) clearance set at 14 mils (0.356 mm).7.4.1.2 Nonabsorbent Stiff Paper Surface4,312 by 6-in. (100by 150-mm).7.4.1.3 Brush-Out Panels4.7.4.1.4 Stop Watch.7.4.1.5 Wire.7.4

    18、.1.6 Weights, 50-g, and 500-g.7.4.1.7 Aluminum Plate,18 by 1 by 2-in. (3 by 25 by50-mm).7.4.2 Procedure:7.4.2.1 Condition the lubricant for at least3hat73.463.6F (23 6 2C). Apply a series of 2 in. wide (wet thickness)(14 6 2.5-mils) 0.356 6 0.064-mm films of the lubricant tofour separate nonabsorben

    19、t paper surfaces. A film applicator asspecified in 7.4.1.1 has been found to produce a wet film in thespecified range with this class of materials, but the depositedfilm thickness from any specific spreader and lubricant systemshould be checked to determine the conformance to thespecified thickness.

    20、 Films should be at least 4 in. (100 mm)long, centered on the paper and parallel to the long axis of thesheet. Allow to dry in a horizontal position in a draft-free area.The time upon completion of the casting of the second film ofeach pair cast is recorded as the initial drying time for that pairof

    21、 films.7.4.2.2 After several minutes drying, cut off at least 112 in.(40 mm) from the bottom of the cast films and discard. Afterdrying 8 min overlap the cut edges of the first pair 1 in. andplace face-to-face to forma1by2-in. area lap shear bond.Take care to align the two films so that a force appl

    22、ied alongtheir center lines will impose a direct shear force without atwisting movement. Form the bond by placing the overlappedpapers on a horizontal smooth surface, placing a18-in. thick, 1by 2-in. aluminum plate over the bond area, and placing a 500g laboratory weight on this plate for 10 s. Hang

    23、 the bondedpieces immediately in a vertical position and attach a 50-gweight with a small loop of wire, weighing less than 1 g, to thelower piece of paperboard forming the bond. Align the point ofsupport and the point of attachment for the weight on the centerlines of the cast films.7.4.2.3 Record t

    24、he time needed for the 50-g load to com-pletely separate the bonded pieces with the aid of a stop watch.If separation is not complete in 1 min, discontinue the test andrecord the separation time as more than 1 min.7.4.2.4 Repeat the above procedure with a pair of cast filmswhich are allowed to dry f

    25、or 20 min before forming a bond.7.4.2.5 Testing should be conducted at 73.4 6 3.6F (23 61C) and at a relative humidity of 50 6 5%.8. Precision and Bias8.1 No statement is made about either the precision or biasof the Test Method in Specification D 2835 for measuringHomogeneity and Drying Rate, since

    26、 the result merely stateswhether there is conformance to the criteria for successspecificed in the procedure.9. Packaging and Package Marking9.1 PackagingThe material shall be packaged in standardcommercial containers, so constructed as to ensure acceptanceby common or other carrier for safe transpo

    27、rtation at the lowestrate to the point of delivery, unless otherwise specified in thecontract or order.9.2 MarkingShipping containers shall be marked with thefollowing information:9.2.1 Manufacturers name or trademark, product code, andbatch or lot number,9.2.2 Date of manufacture and recommended ti

    28、me limit ofstorage before use,9.2.3 Weight per gallon of lubricant to the nearest110 lb(0.05 kg)/gal,9.2.4 Special handling instructions during product transfer,and9.2.5 Special precautions required because of product tox-icity, flammability, or other such information pertinent to theproper storage

    29、and use of the product.3The Gardner Ultra Applicator, available from Gardner Laboratories, Inc., P.O.Box 5728, Bethesda, MD, Catalog No. Ag 3816J, has been found suitable for thispurpose.4Available from the Morest Co., Inc., 211 Center St., New York, NY 10013.D 2835 89 (2003)2SUMMARY OF CHANGESThis

    30、section identifies the location of changes to this standardwhich have been incorporated since the last issue. The Tech-nical Committee has highlighted those changes that affect thetechnical interpretation or use of this standard.(1) Section 1.2 was revised to delete “resistance to aging”.(2) Section

    31、 1.3 was added and the following section renum-bered.(3) The 10-g weight was deleted from 7.4.1.6.(4) The temperature range was broadened in 7.4.2.1 and7.4.2.5.(5) The 4th sentence in Section 7.4.2.2 was revised to correctan omission in the previous published issues.(6) Section 8 on Precision and Bi

    32、as was added.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of suc

    33、h rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for addit

    34、ional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the

    35、 ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 2835 89 (2003)3


    注意事项

    本文(ASTM D2835-1989(2003) Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements《混凝土铺面用预制压缩密封物安装用润滑剂的标准规范》.pdf)为本站会员(livefirmly316)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开