欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D2803-2009(2015) Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal《金属有机涂层耐丝状锈蚀的试验用标准指南》.pdf

    • 资源ID:513533       资源大小:69.65KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D2803-2009(2015) Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal《金属有机涂层耐丝状锈蚀的试验用标准指南》.pdf

    1、Designation: D2803 09 (Reapproved 2015)Standard Guide for TestingFiliform Corrosion Resistance of Organic Coatings onMetal1This standard is issued under the fixed designation D2803; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

    2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This guide covers thr

    3、ee procedures for determining thesusceptibility of organic-coated metal substrates to formationof filiform corrosion.1.2 This guide is limited to the determination of whetherfiliform corrosion will occur between the organic coating andsubstrate.1.3 The values stated in SI units are to be regarded as

    4、 thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the

    5、 applica-bility of regulatory limitations prior to use.NOTE 1Procedure B of this standard is equivalent to ISO 4623.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusD609 Practice for Preparation of Cold-Rolled Steel Panelsfor Testing Paint, Varnish, Co

    6、nversion Coatings, andRelated Coating ProductsD823 Practices for Producing Films of Uniform Thicknessof Paint, Varnish, and Related Products on Test PanelsD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD1654 Test Method for Evaluation of Painted or Coat

    7、edSpecimens Subjected to Corrosive EnvironmentsD1730 Practices for Preparation of Aluminum andAluminum-Alloy Surfaces for PaintingD7091 Practice for Nondestructive Measurement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic, Nonconductive Coat-ings Applied to No

    8、n-Ferrous MetalsE104 Practice for Maintaining Constant Relative Humidityby Means of Aqueous Solutions2.2 International Standard:3ISO 46231 Paints and VarnishesDetermination of resis-tance to filiform corrosionPart 1: On steelISO 46232 Paints and VarnishesDetermination of resis-tance to filiform corr

    9、osionPart 2: On aluminumISO 462810 Paints and VarnishesEvaluation of degrada-tion of coatingsDesignation of quantity and size ofdefects and of intensity of changesPart 10:Assessment offiliform corrosion3. Terminology3.1 Definitions:3.1.1 filiform corrosion, na special type of corrosion thatoccurs un

    10、der coatings on metal substrates that is characterizedby a definite threadlike structure and directional growth.3.1.1.1 DiscussionFiliform corrosion usually occurs be-tween 20 and 35C (70 and 95F), with a correspondingrelative humidity range of 60 to 95 %; above 95 % humidity,blistering rather than

    11、filiform corrosion may occur.4. Summary of Method4.1 Coated metal specimens are scribed and placed in acorrosive atmosphere to initiate corrosion. The specimens arethen exposed to controlled temperature and humidity condi-tions known to be conducive to filiform corrosion.4.2 In Procedure A, panels a

    12、re subjected to a preliminaryexposure in the salt spray cabinet to initiate corrosion, rinsed,and placed in a humidity cabinet. In Procedure B, based on ISO4623, panels are either exposed to salt spray or dipped in a saltsolution but not rinsed before placing in the humidity cabinetoperated at a hig

    13、her temperature than in Procedure A. In1This guide is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.27 on Accelerated Testing.Current edition approved June 1, 2015. Published June 2015. Origi

    14、nallyapproved in 1969. Last previous addition approved in 2009 as D2803 09. DOI:10.1520/D2803-09R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Do

    15、cument Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, Wes

    16、t Conshohocken, PA 19428-2959. United States1Procedure C, specimens are exposed as in Procedure A exceptthe humidity cabinet is operated at a higher temperature.4.3 The procedures contained in this guide differ signifi-cantly in method of initiation, and or temperature, or both, andhumidity of expos

    17、ure and therefore may not yield comparableresults.5. Significance and Use5.1 Some organic coatings applied to metal substrates ex-hibit filiform corrosion when there is a break in the coating filmand the relative humidity is in the 70 to 95 % range.5.2 This guide can be used to determine the suscept

    18、ibility oforganic coated metal substrates to the formation of filiformcorrosion.6. Apparatus6.1 Salt-Spray Chamber as described in Practice B117, forsalt-spray (fog) testing.NOTE 2The preferred initiator of corrosion at the scribe is the salt-fogatmosphere described in Practice B117. Exposure of the

    19、 specimens for 2to4hinaclosed cabinet to the atmosphere above a 1 % acetic acidsolution is an acceptable alternative.6.2 Humidity CabinetAny cabinet with suitable tempera-ture and humidity controls with air circulation may be used.The size and detailed construction of the apparatus areoptional, prov

    20、ided the conditions meet the requirements of thismethod.7. Test Specimen7.1 The composition, surface preparation, and number oftest specimens shall be agreed upon between the producer andthe user. Steel is the preferred substrate, but other metals suchas aluminum, copper magnesium, and stainless ste

    21、el may beused. Zinc and zinc-coated steel are not recommended becausefiliform corrosion generally does not occur on zinc.NOTE 3Applicable test panel description and surface preparationmethods are given in Practice D609 and Practices D1730.7.2 Preparation of Test SpecimensThe method ofapplication, fi

    22、lm thickness, curing, and conditioning shall beagreed upon between the producer and user.NOTE 4Practices D823 gives application methods that can be used toproduce films of uniform film thickness.NOTE 5Test Method D1005 and Practice D7091 give procedures thatcan be used for measurement of dry film th

    23、ickness.7.3 Scribe the test specimen in accordance with Test MethodD1654 or as agreed upon between the producer and user.7.4 The back and edges of the panel should be protectedwith an anti-corrosion coating or tape, unless edge failure isbeing evaluated.8. Use of Control or Reference Materials8.1 Wh

    24、en several coatings are being compared, select acoating as a control. Apply the control coating to the samesubstrate as the test coatings. For best results there should betwo controls, one known to perform well and one known toperform poorly.9. Procedure A9.1 Expose the test specimens to the salt-fo

    25、g atmosphere inaccordance with Practice B117 for at least 4 h and not morethan 24 h, or as agreed upon between the producer and user.9.2 Remove from the salt-fog cabinet and thoroughly rinsewith distilled or demineralized water. Do not permit specimensto dry before placing in the humidity cabinet.9.

    26、3 Place the specimens in the humidity cabinet so that theyare no closer together than 40 mm (1.5 in.) and not in contactwith any metal. Set the cabinet to operate at 25C (77F) and85 % relative humidity unless otherwise agreed upon betweenthe producer and user. The allowed operational limits are 62C(

    27、63.5F) and 610 % relative humidity.NOTE 6The recommended means of maintaining the specified relativehumidity is to utilize trays of saturated potassium chromate solution (650g/L). Practice E104 describes other methods for maintaining relativehumidity, but they may affect the degree and rate of filif

    28、orm corrosion.9.4 Inspect the specimens at intervals of approximately 168h for development of threadlike filaments from the scribe.Exercise care to maintain wetness of specimens duringinspection, since drying stops the original pattern of filiformcorrosion. New filiform may develop on continued expo

    29、surebut at different points.9.4.1 Filiform corrosion will be noted as threadlike fila-ments (see Note 7), initiating at the scribe. A standard methodof rating failure due to filiform is not available. The uniformityof filament growth in direction, width, height and frequencyprecludes a precise ratin

    30、g system. Photographs of filiformfailure are preferred for recording test results. Otherwise, abrief description of the filament growth and their frequency canbe made. ISO 462810 provides a method for the measurementof filiform filaments. Filiform corrosion may continue todevelop after specimens are

    31、 removed from the humiditycabinet.NOTE 7The nature of grinding and grain direction on panels caninfluence the direction of filiform growth.9.5 The normal test period is 6 weeks (1008 h). Otherperiods may be used at the option of the producer and user.10. Procedure B (ISO 4623)10.1 Two alternative in

    32、itiations of corrosion are available,based on initiation by dipping in sodium chloride solution (seeNote 8) or exposure to salt fog. The dipping technique isgenerally preferable for air drying and low-durability materi-als. For high-durability systems such as automotive finishesapplied to phosphated

    33、 steel, the dipping technique may notproduce filiform corrosion and for these systems, it is prefer-able to adopt the salt-fog technique. In such cases, thenecessary period of exposure to salt fog depends on thedurability of the material under test but should rarely need toexceed 24 h.NOTE 8Sodium c

    34、hloride 0.1 % (w/v) solution (for dipping technique)is prepared by dissolving1gofreagent grade sodium chloride (NaCl) in1 L of distilled or demineralized water. Place this solution in a vesselsuitable for complete immersion of the test panel.10.2 Dipping Technique:D2803 09 (2015)210.2.1 Immerse the

    35、scribed specimen for 30 to 60 s in thesodium chloride solution (see Note 8).10.2.2 Take the specimen out of the solution and removeany drops of liquid adhering to it, taking care not to remove thesolution from the scribed marks.10.2.3 Place the specimen in a humidity cabinet set tooperate at 40C (10

    36、4F) and 80 % relative humidity. Theallowed operational limits are 62C (63.5F) and 610 %relative humidity.10.2.4 Repeat the immersion procedure every 3 or 4 daysuntil the end of the test cycle (21 days) or as agreed uponbetween the producer and the user.10.3 Salt-Fog Technique:10.3.1 Expose the scrib

    37、ed test specimen to the salt-fogatmosphere in accordance with Practice B117 for at least4hornot more than 24 h or as agreed upon between the producer andthe user.10.3.2 Remove the test specimen from the salt-fog cabinetand remove any drops of liquid adhering to it, taking care notto remove the solut

    38、ion from the scribed marks.10.3.3 Place the specimen in a humidity cabinet set tooperate at 40C (104F) and 80 % relative humidity for thespecified period agreed upon between the producer and theuser. The allowed operational limits are 62C (63.5F) and610 % relative humidity.10.4 Follow the procedures

    39、 in 9.4 and 9.4.1.11. Procedure C11.1 Expose the test specimens to the salt-fog atmospherein accordance with Practice B117 for at least 4 h and not morethan 24 h, or as agreed upon between the producer and user.11.2 Remove from the salt-fog cabinet and thoroughly rinsewith distilled or demineralized

    40、 water. Do not permit specimensto dry before placing in the humidity cabinet.11.3 Place the specimens in the humidity cabinet so theyare no closer together than 1.5 in. (40 mm) and not in contactwith any metal. Set the cabinet to operate at 40C (104F) and80 % relative humidity. The allowed operation

    41、al limits are62C (63.5F) and 610 % relative humidity.11.4 Follow the procedures in 9.4 and 9.4.1.12. Report12.1 The report shall include the following:12.1.1 Initiation procedure,12.1.2 Humidity cabinet operating temperature,12.1.3 Exposure period, and12.1.4 Rating of coatings as described in 9.4.1.

    42、13. Keywords13.1 filiformASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infring

    43、ement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard

    44、or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views

    45、known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting

    46、ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 09 (2015)3


    注意事项

    本文(ASTM D2803-2009(2015) Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal《金属有机涂层耐丝状锈蚀的试验用标准指南》.pdf)为本站会员(sumcourage256)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开