欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D2416-1984(2009) Standard Test Method for Coking Value of Tar and Pitch (Modified Conradson)《煤焦油和硬沥青的焦化值(改进的残碳)标准试验方法》.pdf

    • 资源ID:512843       资源大小:74.45KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D2416-1984(2009) Standard Test Method for Coking Value of Tar and Pitch (Modified Conradson)《煤焦油和硬沥青的焦化值(改进的残碳)标准试验方法》.pdf

    1、Designation: D2416 84 (Reapproved 2009)Standard Test Method forCoking Value of Tar and Pitch (Modified Conradson)1This standard is issued under the fixed designation D2416; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

    2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the cokingvalue of tar and pitch having an ash content not over 0.5 % a

    3、sdetermined by Test Method D2415.1.2 Coking values by this test method are practically thesame as those obtained by Test Method D189, but results aremore reproducible. The apparatus used is identical, except thatan electric furnace is substituted for the gas flame.1.3 This standard does not purport

    4、to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D140 Pr

    5、actice for Sampling Bituminous MaterialsD189 Test Method for Conradson Carbon Residue of Pe-troleum ProductsD370 Practice for Dehydration of Oil-Type PreservativesD2415 Test Method for Ash in Coal Tar and PitchE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3. Summary of Test Method3

    6、.1 A sample of the tar or pitch is vaporized and pyrolizedfor a specified time at a specified temperature in specialstandardized equipment that limits the available oxygen sup-ply. The percentage of residue is reported as the coking value.4. Significance and Use4.1 This test method is useful for ind

    7、icating the relativecoke-forming propensities and for evaluating and characteriz-ing tars and pitches. This test method can also be used as oneelement in establishing the uniformity of shipments or sourcesof supply.5. Apparatus (see Fig. 1)5.1 CrucibleWide-form, a, either porcelain, glazedthroughout

    8、, or silica, a; 29 to 31-mL capacity, 46 to 49 mm inrim diameter.5.2 Skidmore CrucibleIron crucible, b, flanged andringed, 65 to 82-mL capacity, 53 to 57 mm inside and 60 to 67mm outside diameter of flange, 37 to 39 mm in height, suppliedwith a cover without delivery tubes and having the verticalope

    9、ning closed. The horizontal opening of about 6.5 mm shallbe kept clean. The outside diameter of the flat bottom shall be30 to 32 mm.5.3 Metal Crucible Spun sheet-iron or nickel crucible, c,with cover; 78 to 82 mm in outside diameter at the top, 58 to60 mm in height, and approximately 0.8 mm in thick

    10、ness. Atthe bottom of this crucible, and level before each test, shall bea layer of about 25 mL of sand, or enough to bring theSkidmore crucible, with cover on, nearly to the top of thesheet-iron crucible. The sand shall be dry and screened to passthrough a 65-mesh screen and to be retained on a 200

    11、-meshscreen.5.4 Wire SupportTriangle (65 mm) of bare Nichrome wire1.5 to 2.0 mm in cross section, having an opening small enoughto support the bottom of the metal crucible (see 5.3). Thetriangle, d, shall have its arms bent to form a cradle that willsupport the metal crucible with its bottom level w

    12、ith the bottomof the insulator (see 5.6).5.5 HoodCircular, sheet-iron, e, from 120 to 130 mm indiameter, the height of the lower perpendicular side to be from50 to 53 mm; provided at the top with a chimney 50 to 60 mmin height and 50 to 56 mm in inside diameter, which is attachedto the lower part ha

    13、ving the perpendicular sides by a cone-shaped member, bringing the total height of the complete hoodto 125 to 130 mm. The hood may be made from a single pieceof metal, providing it conforms to foregoing dimensions. Abridge, g, made of approximately 3 mm iron or nichrome wire,and having a height of 5

    14、0 mm above the top of the chimney,shall be attached to handle the chimney when positioning.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.05 on Properties of Fuels, Petroleum Coke and Carbon Ma

    15、terial.Current edition approved Oct. 1, 2009. Published November 2009. Originallyapproved in 1965. Last previous edition approved in 2004 as D241684(2004).DOI: 10.1520/D2416-84R09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org

    16、. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.6 InsulatorCeramic block or refractory ring, f, 150 to175 mm in

    17、diameter if round, or on a side if square, 32 to 38mm in thickness, provided with an inverted cone-shapedopening through the center; 83 mm in diameter at the bottomand 89 mm in diameter at the top.5.7 Vertical Electric Furnace3Bore a hole in the bottomand insert the thermocouple of the pyrometer con

    18、troller so thatits junction is centered exactly 38 mm below the furnaceopening.5.8 Pyrometer Controller4The pyrometer controllershould be checked periodically against a calibrated referencethermocouple, placed alongside but not touching, to ensure thatthe furnace is operating at the desired temperat

    19、ure.Appropriatechanges in the controller circuit should be made, when neces-sary, to maintain the required temperature.5.9 SieveU. S. Standard No. 30 (600-m), conforming toSpecification E11.6. Bulk Sampling6.1 Samples from shipments shall be taken in accordancewith Practice D140, and shall be free o

    20、f foreign substances.Thoroughly mix the sample immediately before removing arepresentative portion for the determination or for dehydration.7. Dehydration of Sample7.1 Hard PitchIf the solid bulk sample contains freewater, air-dry a representative portion.7.2 Soft PitchIf the presence of water is in

    21、dicated bysurface foam on heating, maintain a representative portion ofthe bulk sample at a temperature between 125 and 150C in anopen container until the surface is free from foam. Take carenot to overheat, and remove heat source immediately whenfoam subsides.7.3 TarDehydrate a representative porti

    22、on of the bulksample in accordance with Test Method D370, but stop thedistillation when the temperature reaches 170C. Separate anyoil from the water that has distilled over (if crystals are present,warm sufficiently to ensure their solution), and thoroughly mixthe oil with the residual tar in the st

    23、ill after the latter has cooledto a moderate temperature.8. Preparation of Working Sample8.1 Hard PitchIf the pitch can be crushed at roomtemperature, prepare a 20-g working sample by suitablecrushing, mixing, and quartering of a representative portion ofthe dry sample. The crushing can be done with

    24、 a small jawcrusher and a mortar and pestle. No particle in the representa-tive sample should be larger than 5 mm in any dimension.Crush this sample so that all of it will pass the No. 30 (600-m)sieve but have a minimum of fine particles.8.2 Soft PitchIf the pitch is too soft to grind and to stickyt

    25、o mix, heat a representative portion of the dry sample to thelowest temperature that will permit passage through the No. 30(600-m) sieve, taking care to avoid excessive loss of volatilematter. Do not exceed 10 min for this melting period. Pass theheated sample through the No. 30 (600-m) sieve to rem

    26、oveforeign matter.8.3 TarHeat a representative portion of the dry tar rapidlyto the lowest temperature that will permit passage through theNo. 30 (600-m) sieve, then filter through this sieve to removeforeign matter.8.4 Preservation of SamplesStore samples as large lumpsor as solidified melts in clo

    27、sed containers. Do not save crushedsamples for future analyses since changes in compositionsometimes occur in pulverized pitch.9. Procedure9.1 Ignite a clean porcelain or silica crucible in a mufflefurnace at 900C or over a gas flame for 1 h. Cool in adesiccator and weigh to the nearest 1 mg.9.2 Tra

    28、nsfer a 3-g representative portion of the dry tar orpitch to the tared crucible and weigh to the nearest 5 mg. Placethis crucible in the center of the Skidmore crucible. Level thesand in the metal crucible and place the Skidmore crucible inthe exact center. Apply covers to both the Skidmore and meta

    29、lcrucibles, the one on the latter fitting loosely to allow free exitto the vapors as formed.9.3 Place the triangle on the insulator, center the metalcrucible in the insulator with its bottom resting on top of thetriangle, and cover the whole with the sheet-iron hood andchimney in order to distribute

    30、 the heat uniformly during thecoking process. The assembly, including the insulator ring willbe at approximately room temperature.3The sole source of supply of a Crucible furnace, Hoskins No. FD104, orequivalent, known to the committee at this time is National Element, Inc., 422Oliver Street, Troy,

    31、MI 48084. If you are aware of alternative suppliers, pleaseprovide this information to ASTM International Headquarters. Your comments willreceive careful consideration at a meeting of the responsible technical committee,1which you may attend.4Omega Model D921 Digital Controller with 15 amp relay, av

    32、ailable fromOmega Engineering, Inc., Stamford, CT; or Thermo Electric Model 700, availablefrom Thermo Electric, Saddle Brook, NJ; or equivalent. Minimum line voltagerequired for 220 V furnace is 205 V. If you are aware of alternative suppliers, pleaseprovide this information to ASTM International He

    33、adquarters. Your comments willreceive careful consideration at a meeting of the responsible technical committee,1which you may attend.FIG. 1 Apparatus for Determining Carbon ResidueD2416 84 (2009)29.4 Cover the opening of the furnace with the furnace lidand set the controller to maintain a temperatu

    34、re of 900 6 10C(see 5.8). With the furnace at this temperature, remove the lid,immediately center the assembly (see 9.3) over the furnaceopening and start timing the test period. The positioning of theassembly must be done quickly to avoid excessive loss of heat.Apply heat to the sample for exactly

    35、30 min without changingthe setting of the controller. The temperature should recover to900C in 15 min. At the end of 30 min, remove the assemblyfrom the heat source and allow to cool for about 15 min.Remove the porcelain crucible with heated tongs, place in adesiccator, cool, and weigh.10. Calculati

    36、on10.1 Calculate the coking value of the sample as follows:Coking value, wt. % 5 100A/B (1)where:A = weight of residue, andB = weight of sample.11. Report11.1 Report the coking value to the nearest 0.1 wt %.12. Precision12.1 The following criteria shall be used for judging theacceptability of result

    37、s (95 % probability):12.1.1 Repeatability Duplicate values by the same opera-tor shall not be considered suspect unless the determinedpercentages differ by more than 1.0.12.1.2 Reproducibility The values reported by each oftwo laboratories, representing the arithmetic average of dupli-cate determina

    38、tions, shall not be considered suspect unless thereported percentages differ by more than 2.0.13. Keywords13.1 coking value; ConradsonASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standa

    39、rd are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif

    40、 not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, whi

    41、ch you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D2416 84 (2009)3


    注意事项

    本文(ASTM D2416-1984(2009) Standard Test Method for Coking Value of Tar and Pitch (Modified Conradson)《煤焦油和硬沥青的焦化值(改进的残碳)标准试验方法》.pdf)为本站会员(orderah291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开