欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D451 D451M-2017 Standard Test Method for Sieve Analysis of Granular Mineral Surfacing For Asphalt Roofing Products《沥青屋顶制品用粒状矿物铺面材料筛分分析的标准试验方法》.pdf

    • 资源ID:511735       资源大小:60.61KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D451 D451M-2017 Standard Test Method for Sieve Analysis of Granular Mineral Surfacing For Asphalt Roofing Products《沥青屋顶制品用粒状矿物铺面材料筛分分析的标准试验方法》.pdf

    1、Designation: D451/D451M 91 (Reapproved 2013)1D451/D451M 17Standard Test Method forSieve Analysis of Granular Mineral Surfacing For AsphaltRoofing Products1This standard is issued under the fixed designation D451/D451M; the number immediately following the designation indicates the yearof original ad

    2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTEUnits information was editorially corrected in July 2013.1. Scope1.1 This te

    3、st method covers the determination of the particle size distribution of granular mineral surfacing material such ascrushed slate, stone, coated granules, and so forth, used on the weather surface of prepared asphalt roofing and shingles.1.2 The values stated in either SI units or inch-pound units ar

    4、e to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.3 This standard does not purport to address a

    5、ll of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use.1.4 This international standard was

    6、 developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced D

    7、ocuments2.1 ASTM Standards:2E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves3. Summary of Test Method3.1 A weighed sample of granular mineral surfacing material is separated through a series of sieves of progressively smalleropenings for the determination of particle size distributi

    8、on.4. Significance and Use4.1 This test method is used to determine the grading of materials used as granular mineral surfacing. The results are used todetermine compliance of the particle size distribution with applicable specification requirements.5. Apparatus5.1 SievesA set of the sieves listed i

    9、n Table 1, conforming to Specification E11. For routine testing, the group of sievesactually used shall include only those appropriate for the granular material being graded. Coarser or finer sieves, on which less than0.05 mass % of the specimen would be found after sieving, need not be included in

    10、the group.5.2 Sieve ShakerAmechanically operated sieve shaker thatshaker, which produces a uniform rotary motion and tapping actionwith 140 to 160 taps per minute. The sieve shaker shall be fitted with a hard maple plug to receive the impact of the tapping device.The plug shall be one of the followi

    11、ng: a hard maple plug; a #9 Black Rubber Plug; or a #22 cork plug as chosen by the user. Plugdimensions are: Top Diameter 44 6 1 mm, Bottom Diameter 37 6 1 mm, and Length of 38 6 6 mm. See Note 1. The entireapparatus shall be rigidly mounted by bolting to a solid foundation, preferably concrete.1 Th

    12、is test method is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved July 1, 2013Nov. 1, 2017. Published July 2013December 2017. Originally approved in 1973

    13、. Last previous edition approved in 20082013 asD451 91 (2008).D451/D451M 91 (2013)1. DOI: 10.1520/D0451_D0451M-91R13.10.1520/D0451_D0451M-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolum

    14、e information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequa

    15、tely depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocke

    16、n, PA 19428-2959. United States1NOTE 1Supporting data on the equivalency of the plug materials is on-file at ASTM Headquarters.5.3 Sample SplitterThe riffle sample splitter is an open V-shaped box in which a series of chutes is mounted at right anglesto the long axis to give a series of rectangular

    17、slots of equal area alternatively feeding two trays placed on either side of the trough.The sample is poured into the chute and split into equal portions by the slots, until, after repeated cycles, a sample of the desiredsize is obtained. A riffle sampler with 9.5 or 12.7-mm 38 or 12-in divisions, -

    18、in. divisions shall be used for reducing the sampleto the specimen required for sieve analysis.5.4 BalanceA laboratory balance sensitive to 0.1 g.6. Sampling6.1 Each shipment of mineral granules of a single type shall be considered a unit for sampling. If a shipment contains more thanone type of gra

    19、nule, the entire quantity of each type in the vehicle shall be considered a unit for sampling.6.2 Take the sample of mineral granules shipped in bulk from the chute or conveyor while the vehicle is being loaded orunloaded. The ideal place is just where the material drops from the chute or belt. Coll

    20、ect equal portions from the full width andthickness of the stream at regular intervals with such frequency that a minimum of five samples will be taken and the total massof the sample will not be less than 7.3 kg 16 lb. Do not allow the sampling receptacle to overflow under any circumstances.Overflo

    21、w would tend to reject a higher proportion of the large particles than the small ones, and a representative sample wouldnot be obtained. The sample should not include the initial material discharge from the chute or conveyor.6.3 Take the sample from a shipment of mineral granules shipped in bags, se

    22、lected at random and equal in number to the cuberoot of the total number of bags in the vehicle. Collect equal portions of 800 to 900 g from each of the bags taken for samplingand combine.7. Test Specimen7.1 Reduce the sample by riffling to a specimen of 200 to 250 g. Use the entire specimen obtaine

    23、d from reduction of the samplefor the sieve analysis.7.2 Riffle Splitting ProcedurePlace one empty pan (A however, the entiresplit samples must be used when combining. Do not adjust a sample size by pouring, scooping, or pinching material to or fromthe sample to achieve the target weight. Also, do n

    24、ot discard any of the initial sample material until an accurate split has beencompleted.8. Procedure8.1 Assemble the group of sieves selected from Table 1 in order, with the sieve having the largest opening at the top and theone having the smallest opening at the bottom. Add a solid collecting pan b

    25、elow the bottom sieve. Weigh the test specimen towithin 60.1 g and place in the topmost sieve. Complete the assembly by placing a solid cover over the top sieve. Securely fastenthe sieve assembly in the mechanical sieve-shaking device (see 5.2).8.2 Pass the specimen through the assembled group of si

    26、eves by subjecting it to the action of the sieve shaker for a period of300 6 10 s.TABLE 1 Report FormRetained on Sieve Passing Sieve Percent3.35-mm (No. 6) . . .2.36-mm (No. 8) 3.35-mmA (No. 6) .1.70-mm (No. 12) 2.36-mm (No. 8) .1.18-mm (No. 16) 1.70-mm (No. 12) .850-m (No. 20) 1.18-mm (No. 16) .600

    27、-m (No. 30) 850-m (No. 20) .425-m (No. 40) 600-m (No. 30) .300-m (No. 50) 425-m (No. 40) .212-m (No. 70) 300-m (No. 50) .150-m (No. 100) 212-m (No. 70) .150-m (No. 100) .TotalA Designates U.S. Standard Sieve.D451/D451M 1728.3 Carefully remove the portion of the specimen retained on each of the sieve

    28、s and on the pan, and weigh each portion to within60.1 g.9. Report9.1 Report the results of the sieve analysis to the nearest 0.1 % (omitting the results for those sieves on which less than 0.05mass % of the test specimen was collected), as illustrated in Table 1.9.2 The sum of the percentages repor

    29、ted shall be 1006 100 6 0.2 %.10. Precision10.1 Aretest made after recombining a freshly screened sample by the same operator using the same sieves, should give resultswithin 61 percentage point of the results previously obtained on each sieve. For example, if 32.0 % was retained originally onthe 1.

    30、18-mm (No. 16) sieve, a retest should give between 31.0 and 33.0 %.11. Keywords11.1 asphalt roofing; mineral surfacing; particle size distribution; sieve analysisASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this st

    31、andard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be rev

    32、iewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsib

    33、le technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co

    34、nshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 173


    注意事项

    本文(ASTM D451 D451M-2017 Standard Test Method for Sieve Analysis of Granular Mineral Surfacing For Asphalt Roofing Products《沥青屋顶制品用粒状矿物铺面材料筛分分析的标准试验方法》.pdf)为本站会员(diecharacter305)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开