欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D358-1998(2006) Standard Specification for Wood to Be Used as Panels in Weathering Tests of Coatings《涂料耐大气老试验用木片的标准规范》.pdf

    • 资源ID:511587       资源大小:64.23KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D358-1998(2006) Standard Specification for Wood to Be Used as Panels in Weathering Tests of Coatings《涂料耐大气老试验用木片的标准规范》.pdf

    1、Designation: D 358 98 (Reapproved 2006)Standard Specification forWood to Be Used as Panels in Weathering Tests ofCoatings1This standard is issued under the fixed designation D 358; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

    2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification designa

    3、tes woods for weathering testsof exterior solvent-borne or water-borne paints and othermaterials of similar purpose. Such tests may include eitheroutdoor exposure tests or accelerated laboratory tests. It is thepurpose of this specification to minimize the influence ofvariation of wood of a given sp

    4、ecies on test results.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2D 3924 Specification for Environment for Conditioning andTesting Paint, Varnish, Lacquer, and Related Material

    5、s3. General Considerations3.1 A variety of different species should be used for testingfinishes because of the wide variations in the anatomy and thedensity between wood species. The factors have tremendousinfluences on finish performance. Latewood band width anddensity are especially important to f

    6、inish performance, andthese parameters vary significantly between wood species.Cedar and redwood have relatively low proportions of hardsummerwood distributed in narrow bands and contain extrac-tives that discolor some paint films. Southern pine has a largeproportion of hard summerwood in wide bands

    7、.3.2 The angle between the growth rings and the surface ofthe specimen is very critical to finish performance. Commer-cial practice utilizes the following classification system.Boards in which growth form an angle of less than 30 with thewide surface of the piece are said to be flat-sawn or flat-gra

    8、ined; those with the rings intersecting at angles between 30and 60 are termed bastard-sawn; and those with angles greaterthan 60 are termed quarter-sawn, edge grain, or vertical grain.3.3 Some industrial processors of wood products may uti-lize wood at moisture levels significantly higher than theeq

    9、uilibrium moistures cited in this specification. In thesespecific cases, appropriately higher moisture content panelsmay be prepared for testing of factory applied finishes.WESTERN RED CEDAR4. Species4.1 The material for test panels shall be western red cedar(Thuja plicata).5. Weight per Volume5.1 W

    10、hen the wood is in equilibrium with air at 60 to 65 %relative humidity and 21 6 0.5C (70 6 1F) it shall weigh 350to 370 kg/m3(22 to 23 lb/ft3)orat506 5 % relative humidityand 23 6 2C (73.5 6 3.5F), which are specified inSpecification D 3924 as standard conditions for testing paintand related coating

    11、s, it shall weigh 343 to 359 kg/m3(21.4 to22.4 lb/ft3).NOTE 1The density requirement is to eliminate wood specimens thatvary greatly from the average for that species. Either set of conditions maybe used to establish the density. At 60 to 65 % relative humidity wood hasa moisture content of approxim

    12、ately 12 % while at 45 to 55 % relativehumidity it contains 9 to 10 %. The former is closer to the moisturecontent of wood exposed to most exterior climatic conditions.6. Character of Wood6.1 The wood shall be heartwood having edge grain andshall be free of knots and other defects. The color of the

    13、woodshall be uniform across each panel with no streaks that areexcessively light or dark. The number of annual growth ringsper inch along the radius of the log from which the wood wasobtained shall not be less than ten. The surfaces shall be1This specification is under the jurisdiction of ASTM Commi

    14、ttee D01 on Paintand Related Coatings, Materials and Applications and is the direct responsibilityD01.42 on Architectural Coatings.Current edition approved Aug. 1, 2006. Published August 2006. Originallyapproved in 1933. Last previous edition approved in 1998 as D 358 98.2For referenced ASTM standar

    15、ds, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

    16、19428-2959, United States.smoothly planed and sanded thoroughly with 150 grit sandpa-per within two weeks of testing.7. Thickness of Panels7.1 The minimum thicknesses (Note 2) in proportion towidth (across the grain) shall be as follows:Panel Width, mm (in.)Minimum Thickness, mm(in.)Less than 75 (le

    17、ss than 3) 10 (38)75 to 150 (3 to 6 ) 11 (716)Over 150 (over 6) 19 (34)NOTE 2 Minimum thicknesses in proportion to width (across thegrain) do not apply to panels made of clapboard or siding of commercialtypes, which shall be used as regularly marketed.WHITE PINE AND PONDEROSA PINE8. Species8.1 White

    18、 pine wood shall be northern white pine (Pinusstrobus). Western white pine (Pinus monticola), or sugar pine(Pinus lambertiana). Western white pine is sometimes calledIdaho white pine. Ponderosa pine wood shall be Pinus ponde-rosa.9. Weight per Volume9.1 When the wood is in equilibrium with air at 60

    19、 to 65 %relative humidity and 21 6 0.5C (70 6 1F) it shall weigh 370to 430 kg/m3(23 to 27 lb/ft3)orat506 5 % relative humidityand 23 6 2C (73.5 6 3.5F) it shall weigh 359 to 423kg/m3(22.4 to 26.4 lb/ft3). (See Note 1.)10. Character of Wood10.1 The wood shall be free of knots, pitch pockets, andother

    20、 defects. The color of the wood shall be uniform acrosseach panel with no streaks that are excessively light or dark.The number of annual growth rings per inch along the radius ofthe log from which the wood was obtained shall be not lessthan 15. The surfaces shall be smoothly planed and sandedthorou

    21、ghly with 150 grit sandpaper within two weeks oftesting.10.2 The wood shall be selected as edge grain or flat grainas desired. The test surface of flat grain wood shall be on thebark side.11. Thickness of Panels11.1 The minimum thicknesses (see Note 2) in proportion towidth (across the grain) shall

    22、be as follows:Panel Width, mm (in.)Minimum Thickness, mm(in.)Less than 75 (less than 3) 11(716)75 to 150 (3 to 6) 11 (716)Over 150 (over 6 ) 19 (34)SOUTHERN PINE12. Species12.1 The material for test panels shall be southern pine(Pinus sp.), suitable for siding purposes. It is not to be limitedto a s

    23、ingle species, but shall conform to the requirementsprescribed in Section 13 and Section 14.13. Weight per Volume13.1 When the wood is in equilibrium with air at 60 to 65 %relative humidity and 21 6 0.5C (70 6 1F) it shall weigh 510to 610 kg/m3(32 to 38 lb/ft3)orat506 5 % relative humidityand 23 6 2

    24、C (73.5 6 3.5F) it shall weigh 500 to 590kg/m3(31 to 37 lb/ft3). (See Note 2.)14. Character of Wood14.1 The wood shall be free of knots, pitch pockets, andother defects. The color of the wood shall be uniform acrosseach panel with no streaks that are excessively light or dark.The number of annual gr

    25、owth rings per inch along the radius ofthe log from which the wood was obtained shall be not lessthan 4 nor more than 12. The surfaces shall be smoothly planedand sanded thoroughly with 150 grit sandpaper within twoweeks of testing.14.2 The wood shall be sapwood having flat grain.15. Thickness of Pa

    26、nels15.1 The minimum thicknesses (see Note 2) in proportion towidth (across the grain) shall be as follows:Panel Width, mm (in.)Minimum Thickness, mm(in.)Less than 75 (less than 3) 11(716)75 to 150 (3 to 6) 11 (716)Over 150 (over 6) 19 (34)REDWOOD16. Species16.1 The material for test panels shall be

    27、 redwood (Sequoiasempervirens).17. Weight per Volume17.1 When the wood is in equilibrium with air at 60 to 65 %relative humidity and 21 6 0.5C (70 6 1F) it shall weigh 450to 460 kg/m3(28 to 29 lb/ft3)orat506 5 % relative humidityand 23 6 2C (73.5 6 3.5F) it shall weigh 436 to 452kg/m3(27.2 to 28.2 l

    28、b/ft3). (See Note 1.)18. Character of Wood18.1 The material shall be heartwood, as nearly edge grainas possible. The number of annual growth rings per inch alongthe radius of the log from which the wood was obtained shallbe not less than 18. The wood shall be free of knots, oil streaks,and other def

    29、ects such as wavy burl grain. The color of thewood shall be uniform across each panel with no streaks thatare excessively light or dark. The surfaces shall be smoothlyplaned and sanded thoroughly with 150 grit sandpaper withintwo weeks of testing.19. Thickness of Panels19.1 The minimum thicknesses (

    30、see Note 2) in proportion towidth (across the grain) shall be as follows:Panel Width, mm (in.)Minimum Thickness, mm(in.)Less than 75 (less than 3) 10 (38)75 to 150 (3 to 6) 11 (716)Over 150 (over 6) 19 (34)D 358 98 (2006)2DOUGLAS FIR20. Species20.1 The material for test panels shall be Douglas fir(P

    31、seudotsuga menziesii).21. Weight per Volume21.1 When the wood is in equilibrium with air at 60 to 65 %relative humidity and 21 6 0.5C (70 6 1F) it shall weigh 480to 580 kg/m3(30 to 36 lb/ft3)orat506 5 % relative humidityand 23 6 2C (73.5 6 3.5F) it shall weigh 460 to 560kg/m3(29 to 35 lb/ft3). (See

    32、Note 1.)22. Character of Wood22.1 The wood shall be free of knots, pitch pockets, andother defects. The color of the wood shall be uniform acrosseach panel with no streaks that are excessively light or dark.The number of annual growth rings per inch along the radius ofthe log from which the wood was

    33、 obtained shall be not lessthan ten. The surfaces shall be smoothly planed and sandedthoroughly with 150 grit sandpaper within two weeks oftesting.22.2 The wood shall be heartwood and selected as edgegrain or flat grain as desired. The test surface of flat grain woodshall be on the bark side.23. Thi

    34、ckness of Panels23.1 The minimum thicknesses (see Note 2) in proportion towidth (across the grain) shall be as follows:Panel Width, mm (in.)Minimum Thickness, mm(in.)Less than 75 (less than 3) 11(716)75 to 150 (3 to 6) 11 (716)Over 150 (over 6) 19 (34)24. Keywords24.1 weathering; wood coatings; wood

    35、 panelsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such righ

    36、ts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional

    37、standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM

    38、Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 358 98 (2006)3


    注意事项

    本文(ASTM D358-1998(2006) Standard Specification for Wood to Be Used as Panels in Weathering Tests of Coatings《涂料耐大气老试验用木片的标准规范》.pdf)为本站会员(terrorscript155)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开