欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D1752-2004a(2013) Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction《混凝土铺面和结构建筑用预.pdf

    • 资源ID:510409       资源大小:61.11KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D1752-2004a(2013) Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction《混凝土铺面和结构建筑用预.pdf

    1、Designation: D1752 04a (Reapproved 2013)Standard Specification forPreformed Sponge Rubber Cork and Recycled PVCExpansion Joint Fillers for Concrete Paving and StructuralConstruction1This standard is issued under the fixed designation D1752; the number immediately following the designation indicates

    2、the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the D

    3、epartment of Defense.1. Scope1.1 This specification covers preformed expansion jointfillers of the following four types for use in concrete, brick, orstone construction.1.1.1 Type ISponge rubber.1.1.2 Type IICork.1.1.3 Type IIISelf-expanding cork.1.1.4 Type IVRecycled PVC.1.2 The values stated in in

    4、ch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.NOTE 1Attention is called to Specification D994 and D1751.2. Referenced Documents2.1 ASTM Standards:2D545 Test M

    5、ethods for Preformed Expansion Joint Fillersfor Concrete Construction (Nonextruding and ResilientTypes)D994 Specification for Preformed Expansion Joint Filler forConcrete (Bituminous Type)D1751 Specification for Preformed Expansion Joint Fillerfor Concrete Paving and Structural Construction (Nonex-t

    6、ruding and Resilient Bituminous Types)3. Ordering Information3.1 Products conforming to this specification are manufac-tured in sheet form to a range of thicknesses:14 in.,38 in.,12in.,34 in., and 1 in. Sheet sizes may be 3 or 4 ft in width andlengths of 3, 5, 6, 10, or 12 ft. Purchaser must specify

    7、 sheetsizes when ordering (excluding Type IVRecycled PVC).3.2 Joint filler in strip form is cut from the sheets asmanufactured. When ordering joint filler strips the purchasermust specify thickness, widths, and length; strip widths areavailable from 2 in. (50 mm) in increments of12 in. (13 mm).3.3 T

    8、ype IV joint filler is available in strip form, cut fromthe sheets as manufactured, and available in a range ofthicknesses:14 in.,38 in.,12 in., or34 in. When ordering jointfiller strips, the purchaser must specify thickness, widths, andlength; strip widths are available from 2 in. (50 mm) inincreme

    9、nts of12 in. (13 mm).4. Materials4.1 Sponge RubberThe joint filler shall consist of pre-formed strips of a durable, elastic sponge rubber compound,using synthetic rubber or natural rubber as a base and contain-ing no reclaim rubber or factice. Unless otherwise specified,the sponge rubber shall have

    10、a cement gray color to blend withconcrete in appearance.4.2 Cork and Self-Expanding CorkThe joint filler shallconsist of preformed strips that have been formed from cleangranulated cork particles securely bound together by a syn-thetic resin of an insoluble nature.4.3 Recycled PVCThe joint filler sh

    11、all consist of pre-formed strips that have been extruded using scrap PVCmaterial and using either no binder or a synthetic resin of aninsoluble nature to securely bind it together. Unless otherwisespecified, the recycled PVC should have a cement gray color toblend with concrete in appearance.4.4 Pre

    12、formed strips of expansion joint fillers shall be ofsuch character as not to be deformed or broken by ordinaryhandling when exposed to atmospheric conditions. Pieces ofthe joint filler which have been damaged shall be rejected.5. Requirements5.1 Test SpecimenThe sample to be tested shall be cutfrom

    13、the sheet, as manufactured, and shall be representative ofthe sheet stock.1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.34 onPreformed Joint Fillers, Sealers and Sealing Systems.Current edition app

    14、roved Sept. 1, 2013. Published November 2013. Originallyapproved in 1960. Last previous edition approved in 2008 as D1752 04a (2008).DOI: 10.1520/D1752-04AR13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of

    15、ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.2 RecoveryThe test specimen shall be compressed to50 % of its thickness before test. T

    16、he load shall be releasedimmediately after application. At the end of 10 min afterrelease of application of the load, the specimen shall haverecovered to at least 90 % of its thickness before test.5.2.1 In case of failure to comply with the aboverequirements, the test specimen shall be given three a

    17、pplica-tions of a load sufficient to compress the material to 50 % of itsthickness before test. The load shall be released immediatelyafter each application. At the end of 1 h after the thirdapplication, the specimen shall have recovered to at least 90 %of its thickness before test.5.3 CompressionTh

    18、e load required to compress the testspecimen to 50 % of its thickness before test shall be not lessthan 50 nor greater than 1500 psi (0.34 to 10.35 MPa).5.4 ExtrusionThe test specimen shall be compressed to50 % of its thickness before test with three of the edgesrestrained. The amount of extrusion o

    19、f the free edge shall notexceed 0.25 in. (6.4 mm).5.5 ExpansionIn the case of self-expanding cork (TypeIII) expansion joint filler only, the test specimen after beingimmersed in boiling water for 1 h, shall have a final thicknessnot less than 140 % of the thickness before test. Discolorationof the w

    20、ater shall not be considered an indication of failure.5.6 Boiling in Hydrochloric AcidIn the case of cork andself-expanding cork (Types II and III) expansion joint fillersonly, the test specimen shall show no evidence of seriousdisintegration. Discoloration, or a small amount of swelling,shall not b

    21、e considered as failure. The test specimens shall beexamined immediately after the end of the boiling period andshall be rejected for any of the following evidences ofdisintegration: (1) particles of cork dislodged during theboiling period, (2) specimen lacks resiliency, is very friable,and easily b

    22、roken to pieces, or (3) surface of specimen appearsporous and particles of cork are easily dislodged by rubbingwith fingers. Particles of cork dislodged from edges cut duringpreparation of the specimen should not be considered asconstituting failure under this requirement.5.7 DensityIn the case of s

    23、ponge rubber (Type I) expan-sion joint filler only, the density of the air dry filler shall not beless than 30 lb/ft3(480 kg/m3).5.7.1 In the case of recycled PVC (Type IV) expansion jointfiller only, the density by the dry unit weight test should not beless than 50 lb/ft3.6. Dimensions and Permissi

    24、ble Variations6.1 The preformed strips shall conform to the dimensionsspecified or shown on the plans. Strips of the joint filler whichdo not conform to the specified dimensions, within the permis-sible variations of +116 in. (1.6 mm) in thickness, 618 in. (3.2mm) in depth, and 614 in. (6.4 mm) in l

    25、ength shall be rejected.7. Sampling7.1 Size and Number of SamplesEach sample shall consistof sufficient material to provide at least five test specimensmeasuring 412 by 412 in. (114 by 114 mm). One representativesample, approximately 2 ft2, shall be selected from eachshipment of 1000 ft2or fraction

    26、thereof.7.2 For self-expanding cork joint filler, a minimum of five412 by 412 in. (114 by 114 mm) square specimens properlybanded and plastic wrapped at the point of manufacture shallbe submitted for testing.7.3 Samples shall be packaged for safe transportation to thetesting agency in such a manner

    27、that there will be no danger ofdistortion or breakage.8. Test Methods8.1 Determine the properties prescribed in this specificationin accordance with Test Methods D545.9. Rejection and Retest9.1 Material that fails to conform to the requirements of thisspecification may be rejected. Rejection should

    28、be reported tothe manufacturer or supplier promptly and in writing. In caseof dissatisfaction with the results of the test, the manufactureror supplier may request retesting.10. Packaging10.1 Preformed expansion joint filler in sheets or stripsshould be stored and transported on pallets or suitable

    29、flatsurface to prevent breakage and permanent deformation due toweather conditions.10.2 Self-expanding cork filler shall be wrapped in water-proof paper, sealed in a manner that will prevent the entranceof moisture, and packaged in sizes convenient for handling onthe job.11. Keywords11.1 constructio

    30、n; cork; expansion; joint; paving; pre-formed; PVC; recycled; rubber; sponge; structuralD1752 04a (2013)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

    31、 determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprov

    32、ed or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fee

    33、l that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual repr

    34、ints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1752 04a (2013)3


    注意事项

    本文(ASTM D1752-2004a(2013) Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction《混凝土铺面和结构建筑用预.pdf)为本站会员(unhappyhay135)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开