欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D1582-1998(2017) Standard Test Method for Nonvolatile Content of Liquid Phenol Resorcinol and Melamine Adhesives《液体酚 间苯二酚和三聚氰胺胶粘剂非挥发性含量的标准试验方法》.pdf

    • 资源ID:510091       资源大小:57.87KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D1582-1998(2017) Standard Test Method for Nonvolatile Content of Liquid Phenol Resorcinol and Melamine Adhesives《液体酚 间苯二酚和三聚氰胺胶粘剂非挥发性含量的标准试验方法》.pdf

    1、Designation: D1582 98 (Reapproved 2017)Standard Test Method forNonvolatile Content of Liquid Phenol, Resorcinol, andMelamine Adhesives1This standard is issued under the fixed designation D1582; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

    2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of nonvolatilecontent or total solids of liquid pheno

    3、l, resorcinol, andmelamine adhesives with or without hardener (Note 1) addedand containing high-boiling and low-boiling volatile organicsolvents or water, or both.NOTE 1Some low molecular weight materials in the adhesive may belost if hardener is not used. When a hardener is used, it must be mixed i

    4、naccordance with the manufacturers instructions.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibilit

    5、y of the user of this standard to establish appro-priate safety, health and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific precautions, see 5.2.1.4 This international standard was developed in accor-dance with internationally recognized p

    6、rinciples on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D907 Terminology of Adhesive

    7、s3. Terminology3.1 DefinitionsMany of the terms in this test method aredefined in Terminology D907.4. Summary of Test Method4.1 Without HardenerA weighed amount of adhesive andquartz sand are oven-dried, cooled in a desiccator, andweighed. The percent nonvolatile content is calculated basedon the am

    8、ount remaining.4.2 With HardenerA weighed amount of mixed adhesiveis oven dried, cooled in a desiccator, and weighed. The percentnonvolatile content is calculated based on the amount remain-ing.5. Apparatus5.1 Petri Dish, 00 by 22 mm or its equivalent.5.2 Circulating-Air Oven, capable of maintaining

    9、 tempera-tures of 70 6 1C, 105 6 1C, and 150 6 1C. (Warning Asafety (explosion-proof) oven should be used when volatilematerials are likely to burn or explode.)5.3 Desiccator, with drying agent and tray.5.4 Analytical Balance, accurate to 1 mg.6. Sampling6.1 Except in special cases, take a composite

    10、 sample fromthree or more separate containers chosen at random. Also, takesamples from containers which appear to be nonrepresentativeand test such samples separately. Place the samples immedi-ately in airtight containers, filled to prevent excessive air spaceabove the adhesive, and take precautions

    11、 to reduce evaporationor drying to a minimum. Mix the adhesive in the containerthoroughly if there is a tendency for the materials to separate.6.2 Test three specimens of each sample.7. Procedure7.1 70C Drying Temperature Without Hardener:7.1.1 Place approximately 20 g of the adhesive in a coveredwe

    12、ighing bottle.7.1.2 Place approximately 10 g of fine, oven-dried quartzsand in an open Petri dish, together with a small glass stirringrod, and weigh the dish, rod, and contents to the nearest 1 mgon the analytical balance. Weigh out to the nearest 1 mgapproximately2goftheadhesive by difference from

    13、 theweighing bottle, keeping the bottle covered as much as1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved Aug. 1, 2017. Published August 2017. Originallyapproved in 1958. L

    14、ast previous edition approved in 2011 as D1582 98 (2011).DOI: 10.1520/D1582-98R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary pag

    15、e onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for th

    16、eDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1possible. Mix the adhesive and quartz sand intimately bymeans of the stirring rod and distribute uniformly over thebottom of the dish in as thin a l

    17、ayer as possible. Condition thespecimen at 23 6 1C for at least 16 h.7.1.3 Place the dish with the rod and contents in the oven at70 6 1C until a constant weight is reached.7.1.4 Place the warm dish immediately in the desiccator andallow to cool to room temperature before weighing to thenearest 1 mg

    18、.7.2 70C Drying Temperature With Hardener:7.2.1 Mix approximately 100 g of the adhesive in accor-dance with the manufacturers directions, weighing compo-nents to the nearest 0.01 g.7.2.2 Proceed as in 7.1.2, 7.1.3, and 7.1.4.7.3 105C Drying Temperature Without HardenerProceedas in 7.1 except to plac

    19、e the sample in the oven at 105 6 1C.7.4 105C Drying Temperature With HardenerProceed asin 7.2 except to place the sample in the oven at 105 6 1C.7.5 150C Drying Temperature Without HardenerProceedas in 7.1 except to place the sample in the oven at 150 6 1C.7.6 150C Drying Temperature With HardenerP

    20、roceed asin 7.2 except to place the sample in the oven at 150 6 1C.8. Calculation8.1 Calculate the percent nonvolatile content or total solidsas follows:Nonvolatile content, % 5 wt of residue/wt of specimen! 3100 (1)The weight of the residue is the difference in the weight ofthe dish, rod, and conte

    21、nts before and after heating.8.2 Repeat the test if the results for the three specimens ofa sample do not agree with 60.5 percentage units of oneanother.9. Report9.1 Report the following information:9.1.1 Complete identification of the adhesive tested, includ-ing type, lot number, and source,9.1.2 P

    22、rocedure used,9.1.3 Catalyst or hardener, mixing proportions, and condi-tions used, where applicable,9.1.4 Total drying time to reach constant weight,9.1.5 Number of specimens tested, and9.1.6 Individual nonvolatile content of the three specimensand the average nonvolatile content of the sample.10.

    23、Precision and Bias10.1 A precision and bias statement does not exist for thistest method because resources necessary for round-robin test-ing have not been forthcoming.11. Keywords11.1 adhesives; melamine; nonvolatile content; phenol; re-sorcinolASTM International takes no position respecting the va

    24、lidity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is su

    25、bject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqu

    26、arters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This stand

    27、ard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 98 (2017)2


    注意事项

    本文(ASTM D1582-1998(2017) Standard Test Method for Nonvolatile Content of Liquid Phenol Resorcinol and Melamine Adhesives《液体酚 间苯二酚和三聚氰胺胶粘剂非挥发性含量的标准试验方法》.pdf)为本站会员(proposalcash356)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开