欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C782-2003 Standard Test Method for Softness of Preformed Tape Sealants《预制封缝带柔软性的标准试验方法》.pdf

    • 资源ID:508356       资源大小:23.11KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C782-2003 Standard Test Method for Softness of Preformed Tape Sealants《预制封缝带柔软性的标准试验方法》.pdf

    1、Designation: C 782 03Standard Test Method forSoftness of Preformed Tape Sealants1This standard is issued under the fixed designation C 782; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pare

    2、ntheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes a laboratory procedure fordetermining the softness of preformed tape sealants.NOTE 1Cone penetration methods applicable t

    3、o greases and topetrolatum are described in Test Methods D 217 and D 937. Test MethodD 2451 also uses a penetration technique for determining the degree of setin sash glazing compounds.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parenthesis are for inform

    4、ationonly.1.3 The subcommittee with jurisdiction is not aware of anysimilar ISO standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practice

    5、s and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:C 717 Terminology of Building Seals and Sealants2D 5 Test Method for Penetration of Bituminous Materials3D 217 Test Method for Cone Penetration of LubricatingGrease4D 937 Test Method f

    6、or Cone Penetration of Petrolatum3D 1321 Test Method for Needle Penetration of PetroleumWaxes4D 2451 Test Method for Degree of Set for Glazing Com-pounds on Metal Sash2E 1 Specification for ASTM Thermometers53. Terminology3.1 DefinitionsThe definition of the following term usedin this test method is

    7、 found in Terminology C 717: preformedtape sealant.4. Summary of Test Method4.1 The preformed tape sealant specimen is allowed toequilibrate at standard conditions. A standard needle under adefined load is placed on the specimen for 5 s. The penetrationof the needle into the preformed tape sealant i

    8、s measured.Multiple readings are recorded and averaged.5. Significance and Use5.1 Preformed tape sealants are tacky, deformable solidsthat are used under compression between two substrates in avariety of sealing applications. This procedure measures thesoftness of a preformed tape sealant and gives

    9、an indication ofthe preformed tape sealants ease of compression duringinstallation. The resistance to penetration may also give anindication of the toughness of the preformed tape sealant.6. Apparatus6.1 Needle Penetrometer, as described in Test Method D 5,with a certified needle.NOTE 2Test Method D

    10、 5 describes the needle method for determiningthe penetration of bituminous material; Test Method D 1321 describes asimilar method for use with petroleum waxes, but a different needle isused.6.2 Stop Watch or Timing Mechanism, for the penetrometer.6.3 Thermometer, to measure the temperature of the t

    11、estspecimen in the vicinity of the temperature of the test. For testsat 23 6 0.5C (73 6 1F) a thermometer conforming to therequirements prescribed in Specification E 1 is recommended,such as ASTM Saybolt Viscosity Thermometer 17C (or 17F)having a range from 19 to 27C (66 to 80F).7. Sampling7.1 Sampl

    12、es to be tested shall be taken from a fresh roll ofpreformed tape sealant, after first removing and discardingapproximately the first 600 mm (2 ft) of the roll.7.2 Remove release paper as required in order to fashion asuitable test specimen.8. Test Specimen8.1 Prepare a test specimen by cutting shor

    13、t lengths ofpreformed tape sealant and plying them together to form a solidblock no smaller than 13 mm (0.5 in) wide by 13 mm (0.5 in)by 25 mm (1.0 in) long.1This test method is under the jurisdiction of ASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommitte

    14、e C24.20 onGeneral Sealant Standards.Current editon approved May 10, 2003. Published June 2003. Originallyapproved in 1986. Last previous edition approved in 1999 as C 782 99.2Annual Book of ASTM Standards, Vol 04.07.3Annual Book of ASTM Standards, Vol 04.03.4Annual Book of ASTM Standards, Vol 05.01

    15、.5Annual Book of ASTM Standards, Vol 14.03.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9. Conditioning9.1 Condition the test specimen and the penetrometer,including the needle, for at least2hat236 2C (73 6 3.6F).NOTE 3Other test

    16、temperatures may be used, provided that thespecimen and the penetrometer, including the needle, are conditioned forat least2hatsuch temperature and maintained at that temperature duringthe test. For low temperature testing, for example, both conditioning andtesting must be done in a cold box.10. Pro

    17、cedure10.1 Place the penetrometer in a level position with the shaftset up so that there is a total moving load of 100 g. This loadis comprised of the 2.5-g needle, the 47.5-g shaft, and an extraweight of 50 g placed atop the shaft.10.2 Raise the penetrometer shaft until the pointer on thedial reads

    18、 exactly zero. Lightly tap the indicator dial controllever to ensure that this reading is maintained.10.3 Position the test specimen on the penetrometer so thatit is approximately centered under the needle. Then lower thatpart of the apparatus consisting of the dial gage and shaft withthe needle poi

    19、nt until the needle point just makes contact withthe top surface of the specimen.NOTE 4If the specimen is made from preformed tape sealant less than13 mm (0.5 in.) wide, care should be taken to see that the needle is notplaced in the joint between two abutting strips of preformed tape sealant.10.4 Q

    20、uickly release the needle for 5 s.10.5 Adjust the apparatus to measure the distance throughwhich the needle penetrated the specimen. Record the amountof penetration to the nearest 0.1 mm.10.6 Wipe the penetrometer needle clean. Following thesame procedure, take at least two additional penetration re

    21、ad-ings for the same preformed tape sealant specimen. If readingsare taken on the same specimen surface, the penetration shouldbe made at points at least 7 mm (0.25 in.) from other readings.The amount of penetration for each reading should be recordedseparately and the needle should be wiped clean a

    22、fter eachreading.NOTE 5Unusually low readings, caused by the needle striking anembedded core or other hard material, and unusually high readings causedby penetrating a void or air pocket shall be considered invalid anddisregarded.11. Report11.1 Report the following information:11.1.1 Identification

    23、of the preformed tape sealant, that is,the name, lot number, and any other identifying characteristics.11.1.2 Actual temperature of the test specimen and appara-tus at the time of the test.11.1.3 At least three valid penetration readings and theiraverage.12. Precision and Bias12.1 Interlaboratory ro

    24、und-robin testing of the preformedtape sealant softness has determined the 2s or 95 % confidencelevel of precision for the needle penetrometer test of preformedtape sealant softness at 23 6 0.5C (73 6 1F).12.2 The single-operator-penetrometer-day precision is 0.3mm.12.3 The interlaboratory or multio

    25、perator precision is 1.0mm.NOTE 6The single-operator and interlaboratory precision statementsfor needle penetrometer testing of preformed tape sealant softness at 23C(73F) have been found to hold for tests run at lower tape temperatures,for example, 17.8C (0F). At elevated test temperatures, for exa

    26、mple,70C (158F) penetrometer readings and interlaboratory agreement issomewhat less precise.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determinatio

    27、n of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdra

    28、wn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your c

    29、omments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C782032


    注意事项

    本文(ASTM C782-2003 Standard Test Method for Softness of Preformed Tape Sealants《预制封缝带柔软性的标准试验方法》.pdf)为本站会员(sofeeling205)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开