欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C734-2015 Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering《胶乳密封料受人工气候影响后的低温柔韧性的标准试验方法》.pdf

    • 资源ID:508165       资源大小:55.76KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C734-2015 Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering《胶乳密封料受人工气候影响后的低温柔韧性的标准试验方法》.pdf

    1、Designation: C734 15Standard Test Method forLow-Temperature Flexibility of Latex Sealants After ArtificialWeathering1This standard is issued under the fixed designation C734; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

    2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a laboratory procedure for thedetermination of low-temperature flexibility of latex sealan

    3、tsafter 500 h artificial weathering.1.2 The values stated in metric (SI) units are to be regardedas the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility

    4、of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 1Currently there is no ISO standard similar to this test method.2. Referenced Documents2.1 ASTM Standards:2C717 Terminology of Building Seal

    5、s and SealantsC1442 Practice for Conducting Tests on Sealants UsingArtificial Weathering Apparatus3. Terminology3.1 DefinitionsRefer to Terminology C717 for definitionsof the following terms used in this test method: adhesivefailure, latex sealant, sealant, substrate, and standard condi-tions.4. Sum

    6、mary of Test Method4.1 A slab of the sealant is exposed, after drying, for aminimum of 500 h in an artificial weathering unit, after whichit is conditioned and flexed at 17 6 1C (0 6 2F).5. Significance and Use5.1 This test evaluates the flexibility of artificially weath-ered latex sealants in a low

    7、-temperature environment.6. Apparatus6.1 T3 Temper Alclad Aluminum Panels, three, each 76 by153-mm (3 by 6-in.) of 16 to 24 gage (1.29 to 0.511 mm).6.2 Accelerated Weathering DeviceOne of the units asdescribed in Practice C1442. Because of differences in spectralpower distributions of the exposure s

    8、ources and exposureparameters used in the different types of devices described inPractice C1442, test results may differ with the type ofaccelerated weathering device. Choice of type of device shallbe by mutual agreement among the interested parties.6.3 Cold Box or Freezer.6.4 Mandrel, Wood or Metal

    9、, 25 mm (1 in.) in diameter.6.5 Template, consisting of a 3.2-mm (18-in.) thick brassplate with a rectangular opening 38 by 127 mm (112 by 5 in.).6.6 Spatula, metal.7. Sampling7.1 Take the sealant to be tested directly from the containeras commercially supplied by the manufacturer.8. Test Specimens8

    10、.1 Prepare three test specimens as follows:8.1.1 Center the template on an aluminum panel, fill it toexcess with the sealant, and strike the excess off flush with thesurface of the template with the metal spatula.8.1.2 Cut around the perimeter of the sealant, next to thetemplate, with the spatula, a

    11、nd carefully remove template.9. Conditioning9.1 Condition the three specimens for 2 days at standardconditions.10. Procedure10.1 Place the conditioned specimens in the artificial weath-ering unit and cycle them for a minimum of 500 h, beginningwith the start of the light cycle. Refer to Practice C14

    12、42 for the1This test method is under the jurisdiction ofASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.40 onWeathering.Current edition approved June 1, 2015. Published July 2015. Originally approvedin 1972. Last previous edition approved in 2012

    13、 as C732 06(2012). DOI:10.1520/C0734-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Intern

    14、ational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1artificial weathering unit operating conditions. Expose speci-mens in the xenon arc device for a minimum of 500 h at anirradiance level of 0.51 W(m2 nm) at 340 nm. The radiantexposure for this is 918 kJ/(m2

    15、nm) at 340 nm. To determinethe exposure time required to obtain the same radiant exposureat other irradiance levels specified in Practice C1442, seeAnnex A1 in C1442.10.2 Following artificial weathering exposure, place thespecimens and the mandrel in a cold box maintained at 17 61C (0 6 2F) for 4 h.

    16、10.3 While still in the cold box, place each specimen in turnon the mandrel, with the aluminum plate next to the mandrel,and, without holding the sealant, bend the specimen 90 aroundthe mandrel within 1 s.10.4 Visually examine the specimens after bending, forcracking of the sealant or adhesive failu

    17、re to the aluminum, orboth.11. Report11.1 Report the type and description of the laboratoryaccelerated weathering device, the length of time the testspecimens were exposed in the artificial weathering device andwhether the sealant cracks through to the substrate, or failsadhesively to the aluminum p

    18、anel.12. Precision and Bias12.1 No statement is made about either the precision or biasof this test method for measuring low temperature flexibilitysince the result states merely whether there is conformance tothe criteria for success specified in the procedure.13. Keywords13.1 artificial weathering

    19、; flexibility; latex sealantASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infr

    20、ingement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standa

    21、rd or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your vie

    22、ws known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacti

    23、ng ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 152


    注意事项

    本文(ASTM C734-2015 Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering《胶乳密封料受人工气候影响后的低温柔韧性的标准试验方法》.pdf)为本站会员(terrorscript155)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开