欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C425-2004(2018) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings.pdf

    • 资源ID:466558       资源大小:78.18KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C425-2004(2018) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings.pdf

    1、Designation: C425 04 (Reapproved 2018)Standard Specification forCompression Joints for Vitrified Clay Pipe and Fittings1This standard is issued under the fixed designation C425; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

    2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers

    3、 materials and test requirementsfor compression joints for vitrified clay pipe and fittings. SeeSpecification C700 for pipe specifications. The test require-ments are applicable to pipe joint assemblies prior to fieldinstallation of pipe.NOTE 1Install pipe in accordance with Practice C12.1.2 The val

    4、ues stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following precautionary caveat pertains only to theTest Requirements portion, Section 7,

    5、 of this standard. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety, health, andenvironmental practices and determine the applicability ofregulatory limitations pr

    6、ior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization Technical

    7、Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and Strip (With-drawn 2014)3A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressu

    8、reVessels and for General ApplicationsC12 Practice for Installing Vitrified Clay Pipe LinesC700 Specification for Vitrified Clay Pipe, Extra Strength,Standard Strength, and PerforatedC896 Terminology Relating to Clay ProductsD395 Test Methods for Rubber PropertyCompression SetD412 Test Methods for V

    9、ulcanized Rubber and Thermoplas-tic ElastomersTensionD471 Test Method for Rubber PropertyEffect of LiquidsD518 Test Method for Rubber DeteriorationSurfaceCracking (Withdrawn 2007)3D543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD573 Test Method for RubberDeterioration in

    10、an AirOvenD583 Methods of Test for Water Resistance of TextileFabrics (Withdrawn 1971)3D1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1566 Terminology Relating to RubberD2240 Test Method for Rubber PropertyDurometer Hard-ness3. Terminology3.1 DefinitionsTerms r

    11、elating to plastics and rubber shallbe as defined in Terminologies D583 and D1566, respectively.3.2 Terminology C896 can be used for clarification ofterminology in this specification.4. Principles of Joint Design4.1 Sealing elements shall be compressed between bearingsurfaces to assure watertight in

    12、tegrity as required in Section 7.4.2 Sealing elements shall either be bonded to bearingsurfaces or be independent elements.5. Materials and Manufacture5.1 Rubber ring-sealing elements shall conform to therequirements of Table 1.5.2 Rubber for other than ring-sealing elements shall con-form to the re

    13、quirements of Table 2.1This specification is under the jurisdiction of ASTM Committee C04 onVitrified Clay Pipe and is the direct responsibility of Subcommittee C04.20 onMethods of Test and Specifications.Current edition approved Sept. 1, 2018. Published September 2018. Originallyapproved in 1958. L

    14、ast previous edition approved in 2013 as C425 04(2013). DOI:10.1520/C0425-04R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page

    15、onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recogni

    16、zed principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.3 Plastic components shall conform to the requirements ofTable 3

    17、.5.4 Metallic components shall be of corrosion-resistantmetal conforming to Specifications A167 and A240/A240M.5.5 If any of the test specimens fail to meet the chemicalresistance requirements, the manufacturer will be allowed aretest of two additional specimens, representative of theoriginal materi

    18、al tested, for each one that failed. The jointingmaterial will be acceptable if all retest specimens meet the testrequirements.5.6 Joints complying with this standard are suitable for mostdomestic and commercial applications. However, attention iscalled to the fact that industrial effluents vary in

    19、content,concentration, duration of discharge and temperature; andspecific evaluations of joint performance in such environmentsare necessary. In those instances, consult the manufacturer.6. Joint Specimen Preparation6.1 When required, assembled joints representative of thepipe and joints to be used,

    20、 shall be selected from the suppliersstock by the purchaser or his representative.6.2 Specimens selected for the test shall be up to 0.25 % ofthe number of joints to be furnished. No fewer than twoassembled joints shall be tested for each diameter of pipefurnished.6.3 Test specimens shall not be tak

    21、en from damaged jointsor pipe.7. Test Requirements for Joints7.1 Joints shall meet the requirements of 7.1.1 and 7.1.2 or7.1.1 and 7.1.3, when subjected to an internal 10-ft (3.1-m)head of water pressure (4.3 psi (30 kPa), for a total test periodof 1 h. The recommended temperature of the water, pipe

    22、, andatmosphere is 60 to 75F (16 to 24C).7.1.1 Joints shall not leak when tested in the straightposition and when deflected to amounts shown in Table 4. TheTABLE 1 Tests for RubberRing-Sealing ElementsNOTE 1Except for the water absorption test (Test Method D471), the tests shall be run on specimens

    23、cut from rubber test slabs representative of thefinished product.Test Test Requirement ASTM StandardChemical resistance: D543 (48 h at 23 2C)1N sulfuric acid no weight loss1N hydrochloric acid no weight lossTensile strength 1500 psi (10.4 MPa) min; 500 % min elongation at break D412Hardness Shore A

    24、durometer 35 min to 50 max D2240Compression set 16 % max of original deflection D395, Method B (22 h at 70 2C)Water absorption 5 % max D471Immerse a 2-in. (51-mm) long section cutfrom a rubber-sealing element in distilled waterfor 7 days at 70 2COzone resistance no visible cracking under 2 specimen

    25、magnification us-ing D518, Procedure B, stretched 20 % and exposedto ozone concentrations of 0.5 ppm for 24 h at 40 1CD1149Accelerated oven aging 80 % min of original tensile strength D573 (7 days at 70 2C)75 % min of original elongationTABLE 2 Tests for RubberOther than Ring-Sealing ElementsNOTE 1E

    26、xcept for the water absorption test (Test Method D471), the tests shall be run on specimens cut from rubber test slabs representative of thefinished product.Test Test Requirements ASTM StandardChemical resistance: D543 (48 h at 23 2C)1N sulfuric acid no weight loss1N hydrochloric acid no weight loss

    27、Tensile strength 1000 psi (6.9 MPa) min; 250 % min elongation at break D412Hardness Shore A durometer 55 min to 70 max D2240Compression set 20 % max of original deflection D395, Method B (22 h at 70 2C)Water absorption 5 % max D471Immerse a 2-in. (51-mm) long section cutfrom a rubber coupling in dis

    28、tilled water for 7days at 70 2COzone resistance no visible cracking under 2 specimen magnification, us-ing D518, Procedure B, stretched 20 % and exposedto ozone concentrations of 0.5 ppm for 24 h at 40 1CD1149Accelerated oven aging 85 % min of original tensile strength D573 (7 days at 70 2C)85 % min

    29、 of original elongationTABLE 3 Tests for Plastic MaterialsTest Test Requirements ASTM StandardChemical resistance: D543 (48hat232C)1 N sulfuric acid no weight loss1 N hydrochloric acid no weight lossC425 04 (2018)2ends of the test line shall only be restrained the amount that isnecessary to prevent

    30、longitudinal movement. The deflectionshall be determined by measuring the distance the free end ofone pipe moves away from the center line in any directionwhile the other pipe remains fixed.7.1.2 Assembled joints shall not leak when subjected toshear. The shear load shall be a force of 150 lbf/in. (

    31、26 kN/m)of nominal diameter uniformly applied over an arc of not lessthan 120 (2.1 rad) along a longitudinal distance of not morethan 12 in. (305 mm) at the spigot end of one pipe. The load isapplied immediately adjacent to the assembled joint with theother pipe adequately secured and supported on b

    32、locks placedimmediately adjacent to the joint.7.1.3 Joints shall not leak when the jointed ends are dis-placed relative to one another in any direction perpendicular tothe pipe axis a distance of 0.04 in./in. (0.04 mm/mm) of pipediameter.8. Keywords8.1 bell; chemical resistance; clay pipe; compressi

    33、on joints;corrosion resistance; couplings; deflection; joints; sealing ele-ments; shear; testingSUPPLEMENTARY REQUIREMENTSThese requirements apply only to Federal/Military procurement, not domestic sales or transfers.S1. Government/Military ProcurementS1.1 Responsibility for InspectionUnless otherwi

    34、se speci-fied in the contract or purchase order, the producer is respon-sible for the performance of all inspection and test require-ments specified herein. The producer may use his own or anyother suitable facilities for the performance of the inspectionand test requirements specified herein, unles

    35、s the purchaserdisapproves. The purchaser shall have the right to perform anyof the inspections and tests set forth in this specification wheresuch inspections are deemed necessary to ensure that materialconforms to prescribed requirements.NOTE S1.1In U.S. Federal contracts, the contractor is respon

    36、sible forinspection.S2. Packaging and Marking for U.S. Government Procure-ment:S2.1 PackagingUnless otherwise specified in thecontract, the materials shall be packaged in accordance withthe suppliers standard practice in a manner ensuring arrival atdestination in satisfactory condition and which wil

    37、l be accept-able to the carrier at lowest rates. Containers and packing shallcomply with Uniform Freight Classification rules or NationalMotor Freight Classification rules.S2.2 MarkingMarking for shipment shall be in accordancewith Fed. Std. No. 123 for civil agencies and MIL-STD-129 formilitary age

    38、ncies.NOTE S2.1The inclusion of U.S. Government procurement require-ments should not be construed as an indication that the U.S Governmentuses or endorses the products described in this document.ASTM International takes no position respecting the validity of any patent rights asserted in connection

    39、with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible te

    40、chnical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consider

    41、ation at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr

    42、Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(

    43、www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 4 DeflectionNominal Diameter, in. (mm)Deflection of Pipe, in./linearft (mm/linear m)3 to 12 (76 to 305), incl12 (42)15 to 24 (380 to 610), incl38 (31)27 to 36 (685 to 915), incl14 (21)39 and 42 (990 and 1065)316 (16)48 (1220)18 (10)C425 04 (2018)3


    注意事项

    本文(ASTM C425-2004(2018) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings.pdf)为本站会员(orderah291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开