欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C325-2007 Standard Guide for Wet Sieve Analysis of Ceramic Whiteware Clays《白坯细陶瓷制品粘土的湿筛分析用标准指南》.pdf

    • 资源ID:466292       资源大小:51.13KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C325-2007 Standard Guide for Wet Sieve Analysis of Ceramic Whiteware Clays《白坯细陶瓷制品粘土的湿筛分析用标准指南》.pdf

    1、Designation: C 325 07Standard Guide forWet Sieve Analysis of Ceramic Whiteware Clays1This standard is issued under the fixed designation C 325; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

    2、parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide covers the wet sieve analysis of ceramicwhiteware clays. This guide is intended for use in testingshipments of clay as well as for pl

    3、ant control tests.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety conc

    4、erns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 322 Practice for Sampling Ceramic Whi

    5、teware ClaysE11 Specification for Wire Cloth and Sieves for TestingPurposes3. Apparatus3.1 Stirring DeviceA mechanical stirrer with a three-bladed propeller 2 in. (51 mm) in diameter and having a speedof approximately 1700 r/min, or the equivalent, shall beprovided.3.2 SievesThe sieves shall conform

    6、 to Specification E11and shall include the No. 100 (150-m), No. 140 (106-m), No.200 (75-m) and No. 325 (45-m) sieves (Note 1). The wirecloth for these sieves shall be woven (not twilled) and shall bemounted in circular metal frames 8 in. (203 mm) in diameter,which shall be so constructed as to permi

    7、t nesting of two ormore sieves. A pan and cover for the sieves shall be provided.NOTE 1Equivalent sieves from other standard series, such as the Tylerseries, may also be used. If results are to be compared with those obtainedwith sieves from the ASTM series, it is important that the openings of thes

    8、ieves used fall within the tolerances specified in Specification E11for thecorresponding ASTM sieves.4. Sampling4.1 The sample shall be obtained in accordance with Prac-tice C 322.4.2 The sample as received shall be placed in a drying ovenat 100 to 110C for a period of not less than 5 h prior to tes

    9、ting.5. Procedure5.1 Transfer duplicate portions, of approximately 250 g ofthe dried clay sample, weighed to the nearest 0.1 g, tocontainers of at least 2-L capacity. Wet the clay with 1 L ofwater and allow to slake for 2 h. If a free-flowing slurry is notproduced by this treatment, add another 500

    10、mL of water.5.2 To ensure complete separation of clay from nonplasticimpurities, agitate the slurry by means of a mechanical stirrer(3.1). Continue the stirring between 5 and 10 min.5.3 Transfer the slaked and stirred sample, without loss, tothe finest sieve to be employed in the test, and wash by m

    11、eansof a small jet of water from a14-in. (6.4-mm) soft rubber hoseattached to a water supply having a pressure not in excess ofthat of an ordinary city main. The force of the jet may becontrolled by compressing the end of the hose between thethumb and forefinger. Take care to avoid loss of sample fr

    12、omsplashing. Continue washing until water passing through thesieve shows only traces of sample. Should lumpy materialremain on the screen, return the residue to the stirrer containerby careful washing with a gentle jet of water, and agitate inapproximately 1 L of water for 10 min, then wash the slur

    13、ry aspreviously described.5.4 Wash the residue remaining on the finest sieve into thepan. Thoroughly wet the remaining sieves to be used in the testwith clear water, and nest them in the proper sequence on thefinest sieve. Wash the residue in the pan quantitatively onto thetop sieve, and give the st

    14、ack a preliminary washing.5.5 Nest the top sieve on the pan, which shall contain about12 in. (12.7 mm) of clear water. Wash the residue by holdingthe pan and sieve firmly in the hands, and by a sidewise1This guide is under the jurisdiction of ASTM Committee C21 on CeramicWhitewares and Related Produ

    15、cts and is the direct responsibility of SubcommitteeC21.04 on Raw Materials.Current edition approved Nov. 1, 2007. Published November 2007. Originallyapproved in 1953. Last previous edition approved in 2007 as C 325 81(2007).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon

    16、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.movement, causing wat

    17、er to splash up through the sieve andinto the residue. This movement, coupled with interspersedcircular motions, allows thorough washing. Wash the residueand water remaining in the pan onto the top sieve of the stack.5.6 Again fill the pan with the proper amount of water, nestthe top sieve and its r

    18、esidue on the pan, and repeat theoperation. Continue this until the finest sieve has been washed.Carefully blot each sieve on its underside with a soft, dampsponge, and place the sieve either in a drying oven at 100 to110C or under infrared lamps until thoroughly dry. Approxi-mately2hisrequired with

    19、 a drying oven, but only about 30min with an infrared lamp set 12 in. (305 mm) above the sieve.5.7 Nest the dried residues and sieves in the proper order,with due care to prevent dusting of the residues. Close the stackof sieves with a dry pan and cover, and tap the assembly lightlyfor 1 min on a ta

    20、ble top.5.8 Separate the nested sieves and carefully brush theresidue from each onto a weighing paper. Weigh the residues tothe nearest 0.001 g on an analytical balance.6. Calculation and Report6.1 Calculate the sieve analysis for test sample on the dryweight basis, and report the results to the nea

    21、rest 0.01 % of thematerial retained on each sieve. Report the percentage passingthe finest sieve as the difference between 100 % and the sum ofthe percentages retained on the various sieves.7. Keywords7.1 clay; sieve analysis; wet sieveASTM International takes no position respecting the validity of

    22、any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to r

    23、evision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Yo

    24、ur comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is cop

    25、yrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C325072


    注意事项

    本文(ASTM C325-2007 Standard Guide for Wet Sieve Analysis of Ceramic Whiteware Clays《白坯细陶瓷制品粘土的湿筛分析用标准指南》.pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开