欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C208-2008a Standard Specification for Cellulosic Fiber Insulating Board《纤维质纤维隔热板的标准规范》.pdf

    • 资源ID:466014       资源大小:79.84KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C208-2008a Standard Specification for Cellulosic Fiber Insulating Board《纤维质纤维隔热板的标准规范》.pdf

    1、Designation: C 208 08aStandard Specification forCellulosic Fiber Insulating Board1This standard is issued under the fixed designation C 208; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in par

    2、entheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the principal cellulosic fiberinsulating

    3、board types, grades, and sizes. Requirements arespecified for composition, construction, physical properties,tolerances, sampling procedures, and test methods.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI un

    4、its that are provided for information onlyand are not considered standard.1.3 When the installation or use of thermal insulationmaterials, accessories, and systems may pose safety or healthproblems, the manufacturer shall provide the user appropriatecurrent information regarding any known problems a

    5、ssociatedwith the recommended use of the companys products and shallalso recommend protective measures to be employed in theirsafe utilization. The user shall establish appropriate safety andhealth practices and determine the applicability of regulatoryrequirements prior to use.2. Referenced Documen

    6、ts2.1 ASTM Standards:2C 168 Terminology Relating to Thermal InsulationC 209 Test Methods for Cellulosic Fiber Insulating BoardC 390 Practice for Sampling and Acceptance of ThermalInsulation LotsC 846 Practice for Application of Cellulosic Fiber Insulat-ing Board for Wall SheathingD 1037 Test Methods

    7、 for Evaluating Properties of Wood-Base Fiber and Particle Panel MaterialsD 1554 Terminology Relating to Wood-Base Fiber andParticle Panel MaterialsD 2164 Methods of Testing Structural Insulating RoofDeck3E72 Test Methods of Conducting Strength Tests of Panelsfor Building Construction2.2 Federal Sta

    8、ndard:4900.1 Rev-1 U.S. Dept. of Housing and Urban Develop-ment Minimum Property Standards, One and Two FamilyDwellings43. Terminology3.1 For definitions of terms used in this specification, seeTerminology C 168 and Definitions D 1554.3.2 Definitions of Terms Specific to This Standard:3.2.1 cellulos

    9、ic fiber insulating boarda fibrous-felted,homogeneous panel made from ligno-cellulosic fibers (usuallywood or cane) and having a density of less than 31 lb/ft3(497kg/m3) but more than 10 lb/ft3(160 kg/m3).3.2.1.1 DiscussionCellulosic fiber insulating board ischaracterized by an integral bond which i

    10、s produced byinterfelting of the fibers, but which has not been consolidatedunder heat and pressure as a separate stage in manufacture.Other materials may be added during manufacture to improvecertain properties.4. Classification4.1 Insulating board covered by this specification consists ofsix types

    11、:4.1.1 Type ISound deadening board, for use in wallassemblies to control sound transmissions.4.1.2 Type IIRoof insulation board, for use in variousroofing systems.4.1.2.1 Grade 1Primarily for use under built-up, andmodified bitumen roof systems.4.1.2.2 Grade 2Primarily for use under single-ply, buil

    12、t-up, and modified bitumen roofing systems.4.1.3 Type IIICeiling tiles and panels.4.1.3.1 Grade 1Nonacoustical, for use as decorative walland ceiling coverings.4.1.3.2 Grade 2Acoustical, for use as decorative, soundabsorbing wall and ceiling coverings.4.1.4 Type IVWall Sheathing.1This specification

    13、is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.22 onOrganic and Nonhomogeneous Inorganic Thermal Insulations.Current edition approved Dec. 1, 2008. Published December 2008. Originallyapproved in 1946 . Last previous edition a

    14、pproved in 2008 as C 208 081.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved ve

    15、rsion of this historical standard is referencedon www.astm.org.4Available from the U.S. Department of Housing and Urban Development,Construction Standards Division, HUD Building, Washington, DC 20410.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,

    16、 United States.4.1.4.1 Grade 1Regular, for use as wall sheathing inframe construction.4.1.4.2 Grade 2Structural, for use as wall sheathing inframe construction. When installed in accordance with PracticeC 846, structural wall sheathing provides adequate rackingresistance for use as exterior wall bra

    17、cing.4.1.5 Type VBacker board, for use behind exterior finishin wall assemblies where there are no structural requirements.4.1.6 Type VIRoof deck, for use as roof decking for flat,pitched, or shed-type, open-beamed, ceiling-roof construction.4.2 On occasion these products are used for other applica-

    18、tions. The manufacturer and the purchaser shall agree upon anyspecial requirements for such end uses.5. Materials and Manufacture5.1 Cellulosic fiber insulating board shall be manufacturedfrom refined or partially refined ligno-cellulosic (wood or cane)fibers, by a felting or molding process, into h

    19、omogeneouspanels. Other ingredients may be added to provide or improvecertain properties such as strength and water resistance, inaddition to surface finishes for decorative products and specialcoatings which impart resistance to flame spread. The materialis subjected to such drying temperatures as

    20、to effect completedestruction of rot producing fungi.5.2 The finished board may be either single or multiple ply.When multiple-ply boards are supplied, a suitable moisture-resistant adhesive shall be used to join the plies.6. Physical Properties6.1 The insulating board shall conform to the physicalp

    21、roperties in Table 1.6.2 Roof products with a thickness of 112 in., 212 in., orgreater, are post-laminated using thinner board stock whoseproperties are covered in Table 1.7. Dimensions, Mass, and Permissible Variations7.1 The materials covered by this specification are availablein the sizes shown i

    22、n Table 2.7.2 Length and Width TolerancesUnless otherwise speci-fied, the tolerance for length and width of any size panel shallby+0,116 in. per ft ( + 0, 5.2 mm/m), but the totaltolerance in any dimension shall not exceed + 0, 38 in. ( + 0mm, 10 mm).7.3 Thickness ToleranceThe thickness tolerances a

    23、reshown in Table 3.8. Workmanship, Finish, and Appearance8.1 DefectsThe insulating board shall have no defects thatwill adversely affect its service qualities. The surface shall befree of cracks, lumps, excessive departure from planeness, orother defects that affect performance or appearance.8.2 Sur

    24、face FinishThe surface finishes of the board shallbe as specified in Table 2.8.3 Edge DetailsThe edge details of the board shall be asspecified in Table 2.9. Sampling9.1 Unless otherwise specified in the purchase order orcontract, the material shall be sampled in accordance withPractice C 390.TABLE

    25、1 Physical Property Requirements for Cellulosic Fiber Insulating BoardPhysicalRequirementsSound DeadeningBoard12 in.(13 mm)thickRoof Insulation BoardGrade 1 Grade 2716 in.(11 mm)thick12 in.(13 mm)thick1in.(25 mm)thick2in.(51 mm)thick12 in.(13 mm)thick1in.(25 mm)thick2in.(51 mm)thickThermal conductiv

    26、ity (k), max, 0.38 0.38 0.38 0.38 0.38 0.50 0.40 0.40Btu in./h ft2F (W/mK) at meantemperature of 756 5F (24 6 3C)(0.055) (0.055) (0.055) (0.055) (0.055) (0.072) (0.058) (0.058)Transverse strength either direction,min, lbf (N)12(53.4)7(31.1)7(31.1)14(62.3)28(124.6)12(53.4)24(107)36(160)Tensile streng

    27、th parallel to surface, min,lbf/in.2(kPa)B150(1034)50(345)50(345)50(345). 150(1034)150(1034).Tensile strength perpendicular tosurface, min, lbf/ft2(kPa)600(28.7)500(23.9)500(23.9)500(23.9)500(23.9)600(28.7)600(28.7)600(28.7)Water absorption by volume, max,% 7 10 10 10 10 7 7 7Linear expansion, 5090

    28、% RH, max,% 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5Flame Spread Index, finish surface,max. . . . . . . .Vapor permeance, grains/hft2in. Hgpressure differential, (mg/sm2kPa) min5(0.287). . . . . . .Modulus of rupture, min, lbf/in.2(kPa) 240(1655)140(965)140(965)80(552)40(276)275(1896)140(965)70(483)Deflectio

    29、n at specified min load, max,in. (mm)0.85(22)1.25(32)1.25(32)0.62(16)0.31(8)0.75(19)0.42(11)0.21(5)Modulus of Elasticity, min, lbf/in.23 103(mPa)F. . . . . . . .Deflection Span Ratio, maxF. . . . . . . .Moisture content by weight, max,% 10 10 10 10 10 10 10 10Racking LoadG, min plf (N/m) . . . . . .

    30、 . .C 208 08a210. Test Methods10.1 Unless otherwise specified in Table 1, determine theproperties enumerated in this specification in accordance withTest Methods C 209.11. Inspection and Resubmittal11.1 The following requirements are generally employed forpurposes of acceptance sampling of lots or s

    31、hipments ofqualified material:11.1.1 Surface finish,11.1.2 Edge detail,11.1.3 Dimensional tolerances, and11.1.4 Workmanship.11.2 When agreed upon between the purchaser and themanufacturer or supplier, the inspection of the material shall bemade at either the point of shipment or point of delivery.11

    32、.3 In case of rejection, the manufacturer or supplier shallhave the right to reinspect the rejected shipment and resubmitthe lot after removal of the portion of the shipment notconforming to the specified requirements.12. Product Marking12.1 When specified, each panel or unit shall be labeledwith th

    33、e manufacturers name or trademark, the designation ofthis specification, and type and grade. The label may alsoinclude the mark of a third party certification organization.13. Keywords13.1 backer board; ceiling tiles and panels; cellulosic fiberinsulating board; decorative insulating board; fiberboa

    34、rd; roofdeck; roof insulation board; sound deadening board; thermalinsulation; wall sheathingTABLE 1 Physical Property Requirements for Cellulosic Fiber Insulating Board (continued)PhysicalRequirementsCeiling Tiles and Panels (BothGrades)A12 in.(13 mm)916 in.(14 mm)58 in.(16 mm)Wall SheathingBacker

    35、Board716 in.(11 mm)38 in.(9 mm)thickRoof Deck112 in.(38 mm)2in.(51 mm)3in.(76 mm)thickRegular Structural12 in.(13 mm)thick12 in.(13 mm)thick2532 in.(20 mm)thickThermal conductivity (k), max, 0.38 0.40 0.44 0.40 0.40 0.40Btu in./h ft2F (W/mK) at meantemperature of 756 5F (24 6 3C)(0.055) (0.058) (0.0

    36、63) (0.058) (0.058) (0.058)Transverse strength either direction,min, lbf (N)10(44.5)14(62.3)20(89.0)25(111.2)6(27).Tensile strength parallel to surface,min, lbf/in.2(kPa)B150(1034)150(1034)200(1379)150(1034)150(1034).Tensile strength perpendicular tosurface, min, lbf/ft2(kPa)600(28.7)600(28.7)800(38

    37、.3)600(28.7)600(28.7)600(28.7)Water absorption by volume, max,% . 7C7710Linear expansion, 5090 % RH,max,%0.5 0.5 0.6 0.50.50.5Flame Spread Index, finish surface,max200 . . .200Vapor permeance, grains/hft2in. Hgpressure differential, (mg/sm2kPa)min. 5(0.287)5(0.287)5(0.287)5(0.287)DModulus of rupture

    38、, min, lbf/in.2(kPa). 275(1896)400(2758)200(1379)200(1379)EDeflection at specified min load,max, in. (mm). 0.75(19)0.75(19)0.56(14)1.18(30).Modulus of Elasticity, min, lbf/in.23 103(mPa)F. . . .40(276)Deflection Span Ratio, maxF. . . . . 1/240Moisture content by weight, max,% 10 10 10 10 10 10Rackin

    39、g LoadG, min plf (N/m) . . 650(500)650(500).APhysical properties listed in this column, except flame spread index, apply to the base material before punching, drilling, perforating, or embossing.BTensile strength requirements shall be applicable only on thicknesses up to and including 1 in. (25 mm).

    40、CWater absorption for12 in. structural wall sheathing is determined by the 24-h test in accordance with Test Methods D 1037 using 15 % as the maximum. Waterabsorption for all other products is determined by the 2-h test in accordance with Test Methods C 209.DFor roof deck products with a vapor retar

    41、der, the maximum should be 0.5 (0.029). For roof deck products manufactured without a vapor retarder, there is no requirementfor permeance.EFor roof decking, MOR is determined using Methods D 2164. Matched samples are to be tested before and after accelerated aging. Minimum MOR for unaged samplessha

    42、ll be 225 lbf/in.2(155 kPa). For aged samples, the minimum shall be no less than 50 % of the unaged test result.FUsing Methods D 2164.GThe specified racking results are as tested in accordance with Test Methods E72when the product is applied vertically and fastened 6 in. (152 mm) apart tointermediat

    43、e framing and 3 in. (76 mm) apart around the edges of the sheets using Number 11 gage galvanized roofing nails with716 in. head diameters 114 in. long for12 in. and 112 in. for2532 in The panels shall be tightly butted. Nails shall be38 in. from the edges along the center stud and shall be moved to

    44、the centerline of otherframing. Alternative installation methods as specified by the manufacturer shall be permitted provided the alternative methods achieve a minimum of 650 plf (9500 N/m).C 208 08a3ASTM International takes no position respecting the validity of any patent rights asserted in connec

    45、tion with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsib

    46、le technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful con

    47、sideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100

    48、Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM web

    49、site(www.astm.org).TABLE 2 Nominal Dimensions of Cellulosic Fiber Insulating BoardNominal DimensionsSurface Finish Edge DetailsWidthin. (mm)Lengthin. (mm)Thicknessin. (mm)Sound Deadening Board 48 (1219)48 (1219)96 (2438)108 (2743)12 (13)12 (13)naturalAsquareRoof Insulation 23 (584) 47 (1194)12 (13), 1 (25), 112 (38)2 (51), 212 (64), 3 (76)naturalAor factory surfaceBsquare, offset, or shiplappedGrade 1 and Grade 2 24 (610) 48 (1219)12 (13), 1 (25), 112 (38)2 (51), 212 (64), 3 (76)48 (1219) 48 (1


    注意事项

    本文(ASTM C208-2008a Standard Specification for Cellulosic Fiber Insulating Board《纤维质纤维隔热板的标准规范》.pdf)为本站会员(tireattitude366)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开