欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C142-1997(2004) Standard Test Method for Clay Lumps and Friable Particles in Aggregates《集料中的土块和易碎颗粒含量的标准试验方法》.pdf

    • 资源ID:464583       资源大小:24.62KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C142-1997(2004) Standard Test Method for Clay Lumps and Friable Particles in Aggregates《集料中的土块和易碎颗粒含量的标准试验方法》.pdf

    1、Designation: C 142 97 (Reapproved 2004)American Association of StateHighway and Transportation Officials StandardAASHTO No. T112Standard Test Method forClay Lumps and Friable Particles in Aggregates1This standard is issued under the fixed designation C 142; the number immediately following the desig

    2、nation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by

    3、 agencies of the Department of Defense.1. Scope1.1 This test method covers the approximate determinationof clay lumps and friable particles in aggregates.1.2 The values given in SI units are to be regarded as thestandard. The values given in parentheses are provided forinformation purposes only.1.3

    4、This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Docum

    5、ents2.1 ASTM Standards:2C 33 Specification for Concrete AggregatesC 117 Test Method for Materials Finer Than 75-m (No.200) Sieve in Mineral Aggregates by WashingC 125 Terminology Relating to Concrete and ConcreteAggregatesC 1005 Specification for Reference Masses and Devices forDetermining Mass for

    6、Use in the Physical Testing ofHydraulic CementsE 11 Specification for Wire Cloth and Sieves for TestingPurposes3. Significance and Use3.1 This test method is of primary significance in determin-ing the acceptability of aggregate with respect to the require-ments of Specification C 33.4. Apparatus4.1

    7、 BalanceA balance or scale accurate to within 0.1 % ofthe mass of the test sample at any point within the range of use.Balances shall conform to the accuracy of the applicablesections of Specification C 1005.4.2 ContainersRust-resistant containers of a size andshape that will permit the spreading of

    8、 the sample on thebottom in a thin layer.4.3 SievesSieves conforming to Specification E 11.4.4 Drying OvenAn oven providing free circulation of airand capable of maintaining a temperature of 110 6 5C (230 69F).5. Samples5.1 Aggregate for this test method shall consist of thematerial remaining after

    9、completion of testing in accordancewith Test Method C 117. To provide the quantities designatedin 5.3 and 5.4, it may be necessary to combine material frommore than one test by Test Method C 117.5.2 Dry the aggregate to substantially constant mass at atemperature of 110 6 5C (230 6 9F).5.3 Test samp

    10、les of fine aggregate shall consist of theparticles coarser than a 1.18-mm (No. 16) sieve and shall havea mass not less than 25 g.5.4 Separate the test samples of coarse aggregate intodifferent sizes, using the following sieves: 4.75-mm (No. 4),9.5-mm (38-in.), 19.0-mm (34-in.), and 37.5-mm (112-in.

    11、). Thetest sample shall have a mass not less than indicated in thefollowing table:Size of Particles Making UpTest SampleMass of Test Sample,min, g4.75 to 9.5-mm (No. 4 to38-in.) 10009.5 to 19.0-mm (38 to34-in.) 200019.0 to 37.5-mm (34 to 112-in.) 3000Over 37.5-mm (112-in.) 50001This test method is u

    12、nder the jurisdiction of ASTM Committee C09 onConcrete and Concrete Aggregates and is the direct responsibility of SubcommitteeC09.20 on Normal Weight Aggregates.Current edition approved Aug. 1, 2004. Published August 2004. Originallyapproved in 1938. Last previous edition approved in 1997 as C 142

    13、97.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO B

    14、ox C700, West Conshohocken, PA 19428-2959, United States.5.5 In the case of mixtures of fine and coarse aggregates,separate the material on the 4.75-mm (No. 4) sieve, andprepare the samples of fine and coarse aggregates in accor-dance with 5.3 and 5.4.6. Procedure6.1 Determine the mass of the test s

    15、ample to the accuracyspecified in 4.1 and spread it in a thin layer on the bottom of thecontainer, cover it with distilled water, and soak it for a periodof 24 6 4 h. Roll and squeeze particles individually betweenthe thumb and forefinger to attempt to break the particle intosmaller sizes. Do not us

    16、e the fingernails to break up particles,or press particles against a hard surface or each other. Classifyany particles that can be broken with the fingers into finesremovable by wet sieving as clay lumps or friable particles.After all discernible clay lumps and friable particles have beenbroken, sep

    17、arate the detritus from the remainder of the sampleby wet sieving over the sieve prescribed in the following table:Size of Sieve for RemovingSize of Particles Making Up Residue of Clay Lumps andSample Friable ParticlesFine aggregate (retained on1.18-mm (No. 16) sieve)850-m (No. 20)4.75 to 9.5-mm (No

    18、. 4 to38-in.) 2.36-mm (No. 8)9.5 to 19.0-mm (38 to34-in.) 4.75-mm (No. 4)19.0 to 37.5-mm (34 to 112-in.) 4.75-mm (No. 4)Over 37.5-mm (112-in.) 4.75-mm (No. 4)Perform the wet sieving by passing water over the samplethrough the sieve while manually agitating the sieve, until allundersize material has

    19、been removed.6.2 Remove the retained particles carefully from the sieve,dry to substantially constant mass at a temperature of 110 65C (230 6 9F), allow to cool, and determine the mass to thenearest 0.1 % of the mass of the test sample as defined in 5.3or 5.4.7. Calculation7.1 Calculate the percent

    20、of clay lumps and friable particlesin fine aggregate or individual sizes of coarse aggregate asfollows:P 5 M 2 R!/M 3 100 (1)where:P = percent of clay lumps and friable particles,M = mass of test sample (for fine aggregate the mass of theportion coarser than the 1.18-mm (No. 16) sieve asdescribed in

    21、 5.3), andR = mass of particles retained on designated sieve asdetermined in accordance with 6.2.7.2 For coarse aggregates, the percent of clay lumps andfriable particles shall be an average based on the percent ofclay lumps and friable particles in each sieve size fractionweighted in accordance wit

    22、h the grading of the original samplebefore separation or, preferably, the average grading of thesupply represented by the sample. Should the aggregate con-tain less than 5 % of any of the sizes specified in 6.1, that sizeshall not be tested but, for the purpose of calculating theweighted average, sh

    23、all be considered to contain the samepercent of clay lumps and friable particles as the next larger ornext smaller size, whichever is present.8. Precision and Bias8.1 Precision3The estimate of the precision of this testmethod is provisional and is based on samples of one fineaggregate that was teste

    24、d by ten different operators at ninedifferent laboratories. For that sample, the average “percent ofclay lumps and friable particles” in the aggregate was 1.2 %,and the standard deviation was 0.6 %. Based on this standarddeviation, the acceptable range of two test results on samplesfrom the same agg

    25、regate sent to different laboratories is 1.7 %.8.2 BiasSince there is no acceptable reference materialfor determining the bias for the procedure in this test method,no statement is being made.9. Keywords9.1 aggregates; clay lumps; friable particlesASTM International takes no position respecting the

    26、validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

    27、subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Head

    28、quarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This sta

    29、ndard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).3Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR: C09-1016.C 142 97 (2004)2


    注意事项

    本文(ASTM C142-1997(2004) Standard Test Method for Clay Lumps and Friable Particles in Aggregates《集料中的土块和易碎颗粒含量的标准试验方法》.pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开