欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C1110-2003 Standard Practice for Sample Preparation for X-Ray Emission Spectrometric Analysis of Uranium in Ores Using the Glass Fusion or Pressed Powder Method《使用玻璃熔化或压制粉末法制备.pdf

    • 资源ID:463414       资源大小:27.25KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C1110-2003 Standard Practice for Sample Preparation for X-Ray Emission Spectrometric Analysis of Uranium in Ores Using the Glass Fusion or Pressed Powder Method《使用玻璃熔化或压制粉末法制备.pdf

    1、Designation: C 1110 03Standard Practice forSample Preparation for X-Ray Emission SpectrometricAnalysis of Uranium in Ores Using the Glass Fusion orPressed Powder Method1This standard is issued under the fixed designation C 1110; the number immediately following the designation indicates the year ofo

    2、riginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the preparation of uranium oresamples

    3、to be analyzed by X-ray emission. Two separatetechniques, the glass fusion method or the pressed powdermethod, may be used.1.2 The values stated in SI (metric) units are to be regardedas the standard.1.3 This standard does not purport to address all of thesafety problems, if any, associated with its

    4、 use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:E 50 Practices for Apparatus, Reagents, and Safety Precau-tions for Chemi

    5、cal Analysis of Metals2E 135 Terminology Relating to Analytical Chemistry forMetals, Ores, and Related Materials23. Terminology3.1 DefinitionsRefer to Terminology E 135 for terms usedin this practice.4. Summary of Practice4.1 Two types of specimen preparation methods are offered.These are the glass

    6、fusion technique and the pressed powdertechnique. The glass fusion specimens are fused and cast intodisks in a platimum-gold alloy crucible in the presence of anoxidizing agent at a preset temperature and time. The pressedpowder specimens are ground in a mill to a specified particlesize and briquett

    7、ed into a solid specimen possessing a flathomogeneous surface to be analyzed.5. Significance and Use5.1 This practice is useful for the preparation of specimensof ore bodies for the analysis of uranium by X-ray emission.Two separate preparation techniques are described.6. Apparatus6.1 Platimum-Gold

    8、Crucible, 95 % platinum 5 % gold, withflat 32-mm diameter bottom.6.2 Muffle Furnace, 1200C capacity with controller of610C resolution, or fusion apparatus with similar capabili-ties.NOTE 1A fusion apparatus may be substituted for the muffle furnacethroughout this practice. If such is used, follow th

    9、e manufacturersoperating instructions.6.3 Rotary Swing Mill, with tungsten or boron carbide vials.6.4 Pellet Die, 32-mm diameter.6.5 Hydraulic Press, 25-ton capacity.6.6 Crucible, porcelain, Coors, 30-mL capacity.6.7 Refractory Brick, 60 to 70 % alumina firebrick.6.8 Analytical Balance, accurate to

    10、60.001 g.7. Reagents and Materials7.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents conform to the specifications of the Committee onAnalytical Reagents of the American Chemical Society, wheresuch specifications are a

    11、vailable.3Other grades may be used,provided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination (see Practices E 50).7.2 Lithium Tetraborate(Li2B4O7), anhydrous, spectro-graphic grade.7.3 Oxidizing Agent, ammoniu

    12、m nitrate (NH4NO3).7.4 Ethanol, anhydrous.1This practice is under the jurisdiction of ASTM Committee C26 on NuclearFuel Cycle and is the direct responsibility of Subcommittee C26.05 on Methods ofTest.Current edition approved July 10, 2003. Published September 2003. Origianllyapproved in 1988. Last p

    13、revious edition approved in 1997 as C111088(1997)e1.2Annual Book of ASTM Standards, Vol 03.05.3“Reagent Chemicals, American Chemical Society Specifications,” Am. Chemi-cal Soc., Washington, DC. For suggestions on the testing of reagents not listed bythe American Chemical Society, see “Reagent Chemic

    14、als and Standards,” by JosephRosin, D. Van Nostrand Co., Inc., New York, NY, and the “United StatesPharmacopeia.”1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.5 Binding Agent, for example, pelletizing grade graphitepowder, cellul

    15、ose powder, “Somar Mix,” or equivalent.7.6 Boric Acid, 99.9 % pure.8. Preparation of Standards and Specimens8.1 Glass Fusion Method:8.1.1 Ignition Loss of Lithium Tetraborate:NOTE 2Commercially availabe fused and ground lithium tetraboratemay be used, and only the 105C drying step is required.8.1.1.

    16、1 Heat a 95 % platinum/5 % gold crucible in a mufflefurnace at 1100C for at least 10 min and cool to roomtemperature in a dessicator.8.1.1.2 Weigh the cooled crucible on an analytical balanceto 60.001 g (W1).8.1.1.3 Add to the tared crucible approximately5goflithium tetraborate weighed to the neares

    17、t 60.001 g ( W2).8.1.1.4 Heat the crucible plus lithium tetraborate in themuffle furnace at 1100C for 15 min.8.1.1.5 Remove the crucible from the furnace, cool, andstore in a desiccator.8.1.1.6 Weigh the crucible plus the ignited lithium tetrabo-rate on an analytical balance to 60.001 g (W3).8.1.1.7

    18、 Calculate the ignition factor in accordance withSection 9.8.1.1.8 Remove the lithium tetraborate glass by invertingthe crucible and tapping lightly on the bottom. Save this pelletto use as a blank in future calibrations.8.1.1.9 Clean the platinum crucible.8.1.1.10 Determine the loss on ignition for

    19、 samples byfollowing 8.1.1.1 through 8.1.1.7, except ignite 2.0 g of samplein a porcelain crucible.NOTE 3Moist specimens should be previously dried at 105C for 1 h,and the loss on drying should be recorded.8.1.2 Specimen Fusion:NOTE 4Numerous ores contain sulfide minerals which at high tem-peratures

    20、 will attack the platinum/gold crucible. For specimens thatcontain sulfide minerals, pre-oxidize a 2-g specimen plus 1.000 g ofammonium nitrate in a porcelain crucible for 15 min at 1100C. Cool theporcelain crucible, and then use the pre-oxidized material as the specimenand proceed with 8.1.2.1. Ore

    21、s that contain high concentrations of alkalielements may attack porcelain crucibles; therefore, graphite crucibles arerecommended for this pre-oxidation step.8.1.2.1 Weigh 2.000 g of the specimen into a tared porcelaincrucible and ignite at 1100C for 15 min. Cool and reweigh thecrucible and specimen

    22、.8.1.2.2 Weigh 5.000 g of loss-free equivalent lithium tet-raborate (determined from igniting the lithium tetraborate),1.000 g of ignited specimen, and 0.5000 g of ammoniumnitrate, all to the nearest 0.001 g.8.1.2.3 Transfer all three components into a 95 % platinum/5 % gold crucible and briefly mix

    23、.8.1.2.4 Place the crucible and contents in a muffle furnace at1100C and fuse for 5 min.8.1.2.5 Remove the crucible from the furnace with longcrucible tongs and swirl the molten material to ensure completesolution and eliminate bubbles.8.1.2.6 Replace the crucible in the furnace for another 5min.8.1

    24、.2.7 Repeat 8.1.2.5 and 8.1.2.6 until all of the specimenis dissolved.8.1.2.8 Remove the crucible from the furnace, place on arefractory brick, and allow it to cool to room temperature.8.1.2.9 When the crucible is cool, invert and lightly tap it tofree the glass disk.8.1.2.10 Clean the crucible.8.2

    25、Pressed Powder Method:8.2.1 Grind a representative portion of the specimen weigh-ing at least5gto44m(325 mesh).4Mix the resultingpowdered specimen if necessary.NOTE 5Grinding aids may improve grinding time and efficiency.58.2.2 Press5goftheground specimen at 25 tons for 30 s.Use a suitable pelletizi

    26、ng agent, if necessary.8.2.3 Clean the mill and die to avoid contaminating the nextspecimen. Brush any remaining powder residue from the milland wipe out remaining traces with a paper towel wetted witha suitable solvent such as ethanol. Clean the die assembly in asimilar manner.8.3 Prepare all calib

    27、ration standards using the same methodas used for specimen preparation.9. Calculation9.1 Ignition Factor Calculate the ignition factor as fol-lows:IF 5 W32 W1!/W22 W1! (1)where:IF = ignition factor,W1= weight of crucible, g,W2= weight of crucible and fusion powder before igni-tion, g, andW3= weight

    28、of crucible and fusion powder after ignition,g.10. Precision and Bias10.1 No statement is made about the precision or the bias ofthis practice since this practice addresses only preparation forspecimen analysis, and therefore no data are generated.11. Keywords11.1 glass fusion; pressed powders; samp

    29、le preparation;uranium ores; x-ray fluorescence4Wheeler, B., “Particle Size Effects in X-ray Fluorescence Analysis,” Advancesin X-ray Analysis, Proceedings of the 32nd Annual Conference on Application ofX-ray Analysis, Vol 27, Denver, CO, Aug 1984.5Berstein, F., “Particle Size and Mineralogical Effe

    30、cts in Mining Applications,”11th Annual Conference on Application of X-ray Analysis, Denver ResearchInstitute, University of Denver, Denver, CO, 1962.C1110032ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standa

    31、rd. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewe

    32、d every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible

    33、technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C1110033


    注意事项

    本文(ASTM C1110-2003 Standard Practice for Sample Preparation for X-Ray Emission Spectrometric Analysis of Uranium in Ores Using the Glass Fusion or Pressed Powder Method《使用玻璃熔化或压制粉末法制备.pdf)为本站会员(progressking105)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开