欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C1104 C1104M-2013a Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation《测定未覆面矿物纤维绝缘材料水蒸汽吸收性的标准试验方法》.pdf

    • 资源ID:463394       资源大小:72.58KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C1104 C1104M-2013a Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation《测定未覆面矿物纤维绝缘材料水蒸汽吸收性的标准试验方法》.pdf

    1、Designation: C1104/C1104M 13C1104/C1104M 13aStandard Test Method forDetermining the Water Vapor Sorption of Unfaced MineralFiber Insulation1This standard is issued under the fixed designation C1104/C1104M; the number immediately following the designation indicates the yearof original adoption or, in

    2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the amount of water vapor sorbed by mi

    3、neral fiber insulation exposed to ahigh-humidity atmosphere. This test method is applicable only to fibrous base material and binder. The results obtained by this testmethod cannot be used in describing faced products, since the facing is not tested by using this test method.1.2 The water vapor sorp

    4、tion characteristics of materials may be affected by conditions such as elevated temperatures orchemical exposures. Values obtained as a result of this test method may not adequately describe the water vapor sorptioncharacteristics of materials subjected to these conditions.1.3 The values stated in

    5、either SI units or inch-pound units are to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.4 This

    6、standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1

    7、 ASTM Standards:2C167 Test Methods for Thickness and Density of Blanket or Batt Thermal InsulationsC302 Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal InsulationC303 Test Method for Dimensions and Density of Preformed Block and BoardType Thermal InsulationC390 Practic

    8、e for Sampling and Acceptance of Thermal Insulation LotsE177 Practice for Use of the Terms Precision and Bias in ASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Th

    9、e term sorption has been adopted for this test method, since mineral fiber insulation may absorb water within its bulkwhen viewed macroscopically, while it adsorbs water onto individual fibers on a microscopic scale.(1) sorptionrefers to the taking up and holding of matter by other matter by various

    10、 processes such as absorption andadsorption.(2) absorptionrefers to the taking up of matter in-bulk by other matter; for example, the penetration of substances into thebulk of another solid or liquid.(3) adsorptionrefers to surface retention or adhesion of an extremely thin layer of molecules to the

    11、 surfaces of solids orliquids with which they are in contact.4. Summary of Test Method4.1 The insulation is dried to a constant weight and exposed to a high-humidity atmosphere for 96 h. The amount of watersorbed from the vapor phase is the difference in specimen weights, and is expressed in either

    12、weight or volume percent.1 This test method is under the jurisdiction of Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation Finishes andMoisture.Current edition approved Jan. 15, 2013Nov. 1, 2013. Published January 2013December 2013. Originally

    13、approved in 1988. Last previous edition approved in 20062013as C1104/C1104M 00C1104/C1104M 13.(2006). DOI: 10.1520/C1104_C1104M-13.10.1520/C1104_C1104M-13A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM

    14、 Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically pos

    15、sible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, W

    16、est Conshohocken, PA 19428-2959. United States15. Significance and Use5.1 The sorption of water can result in an increase in weight and a resultant potential degradation of the properties of theinsulation.6. Apparatus6.1 Air-circulating oven, capable of maintaining a temperature between 102 and 121C

    17、 215 and 250F.6.2 Desiccator, with calcium chloride as a desiccant.6.3 Scale, accurate to 60.1 % of specimen weight.6.4 Environmental test chamber, capable of maintaining a temperature of 49 6 2C 120 6 3F and a relative humidity of 956 3 %.6.5 Steel rule, graduated in 1 mm or 0.05 in. intervals with

    18、 depth gauge as described in Test Methods C167.6.6 Sealable polyethylene sample bags of a size large enough to accommodate the test specimens (for blanket, board, or pipethermal insulations).6.7 Non-water-sorbing, non-corrosive tray with tight-fitting lid measuring at least 15 by 15 cm 6 by 6 in. (f

    19、or loose-fillinsulations).7. Sampling and Test Specimens7.1 Three specimens shall be tested, unless otherwise stated in the appropriate material specification. These are to be obtainedfrom one representative package of insulation. Sampling techniques should be in accordance with Practice C390.7.2 Fo

    20、r blanket and board products, the test specimen shall be of a size that can be conveniently tested in the environmentalchamber, but not smaller than 15 by 15 cm 6 by 6 in. by the full sample thickness. For pipe insulation products, use a 15 cm6 in. length and as much of the circumference as can be c

    21、onveniently tested. For loose-fill products, the test specimen shall consistof sufficient quantity of the material to fill a preweighed container measuring at least 15 by 15 cm 6 by 6 in., to a nominal depthat its nominal density.7.3 The insulation shall be tested without facing or jacketing, unless

    22、 otherwise agreed upon by the purchaser and supplier, orunless otherwise specified by the appropriate material specification.8. Procedure A, for Blanket, Board, and Pipe Insulation Products8.1 If it is necessary to determine volume percent, measure the dimensions and calculate the density of the spe

    23、cimens using8.1.1, 8.1.2, or 8.1.3.8.1.1 For blanket products, measure the length and width of the specimens using a steel rule. Measure the weight of thespecimens. Measure the thickness of the specimens by means of the depth gage as stated in Test Method C167. Calculate thedensity of the specimens.

    24、8.1.2 For board products, measure the dimensions of the specimens using the test methods stated in Test Method C303.8.1.3 For pipe products, measure the dimensions of the specimens using the test methods stated in Test Method C302.8.1.4 Calculate the volume of the specimens. If requested, the volume

    25、 may be based on the nominal thickness rather than themeasured thickness, but this must be included in the report.8.2 Determine the moisture-free weight of each specimen in the manner described in 8.2.1.8.2.1 Weigh the specimen. Place the specimen in an air-circulating oven at a temperature of 102 t

    26、o 121C 215 to 250F fora minimum of 2 h. (See Note 1.) Cool the specimen to room temperature in a desiccator and reweigh. Repeat the process untilsuccessive weighings agree to within 0.2 % of the specimen weight obtained in the latest weighing. Record this weight as themoisture-free weight.NOTE 1When

    27、 drying at the specified temperature has been shown to adversely affect the insulation, the specimen may be dried to moisture-freeweight in a desiccator at room temperature. However, the drying time between successive weighings should then be extended to at least 24 h.8.3 Bring the specimens to a un

    28、iform temperature in an oven of not less than 60C 140F and then transfer to theenvironmental chamber. Either suspend the specimens or place on a grid within the chamber in order to ensure air circulationaround the specimens. Protect the specimens from condensate dripping from the chamber ceiling by

    29、using a slanting false roofimmediately above the specimens.8.4 Allow the specimens to remain in the environmental chamber for 966 4 h at a temperature of 49 6 2C 1206 3F andat a relative humidity of 95 6 3 %. Then place each specimen in its own pre-weighed sample bag, seal the bag, and remove fromth

    30、e chamber. Allow the bag containing the specimens to cool to room temperature and weigh. Subtract the bag weight from theobtained weight. Record this as the specimen weight after testing.C1104/C1104M 13a29. Procedure B, for Loose-Fill Insulation Products9.1 If it is necessary to determine volume per

    31、cent, measure the length and width of the pre-weighed sample trays, using a steelrule. Apply the insulation at its nominal or requested thickness and density by pouring or blowing it into the sample tray. Measurethe thickness of the specimens by means of a depth gauge. Calculate the volume of the sp

    32、ecimens.9.2 Determine the moisture-free weight of each specimen in the manner described in 9.2.1.9.2.1 Weigh the sample tray containing the specimen. Place the specimen in an air-circulating oven at a temperature of 102to 121C 215 to 250F for a minimum of 2 h. (See Note 1.) Place the pre-weighed lid

    33、 on the sample tray, cool the specimento room temperature, and reweigh. Remove the lid and repeat the process until successive weighings agree to within 0.2 % of thespecimen weight obtained in the latest weighing. Subtract the tray weight from the total obtained weight of the tray and specimen.Recor

    34、d this weight as the moisture-free weight of the specimen.9.3 Remove the lids and bring the specimens to a uniform temperature of not less than 60C 140F, and then transfer to theenvironmental chamber. Place the trays horizontally within the chamber and place the lids next to the trays. Protect the s

    35、pecimensfrom condensate dripping from the chamber ceiling by using a slanting false roof immediately above the specimens.9.4 Allow the specimens to remain in the environmental chamber for 96 6 4 h at a temperature of 49 6 2C 120 6 3Fand at a relative humidity of 95 6 3 %. Then place the lid on each

    36、sample tray and remove from the chamber. Allow the traycontaining the specimen to cool to room temperature and weigh. Subtract the tray weight from the obtained weight. Record thisas the specimen weight after testing.10. Calculation10.1 Calculate the percentage water vapor sorption by weight and by

    37、volume using Eq 1, Eq 2, and Eq 3.10.1.1 Water sorbed from the vapor phase,weight percent5W22W1!W13100 (1)where:W2 = specimen weight after test, andW1 = moisture-free weight of specimen.10.1.2 Water sorbed from the vapor phase,volume percent5W22W1!31001g/cm3!3V (2)where:W2 and W1 = are in grams,V =

    38、is the samples volume in cm3, and1 g/cm3 = is the density of water.10.1.3 An alternative method of calculating volume percent is shown in Eq 3:Water sorbed from the vapor phase,volume percent (3)5Water sorption,weight percent!3Sample density!Density of waterwhere the sample density and the density o

    39、f water are in the same units, such as g/cm3, lb/ft3, or lb/in.311. Report11.1 The report shall include the following:11.1.1 Name and any additional identification of the material tested,11.1.2 Thickness of the material,11.1.3 Number of specimens tested,11.1.4 Density,11.1.4.1 Measured density (blan

    40、ket, board, and pipe product),11.1.4.2 Applied density (for loose fill only),11.1.5 The average percent water sorption by weight for the specimens, and11.1.6 The average percent water sorption by volume for the specimens, if requested.12. Precision and Bias12.1 Interlaboratory Test ProgramInterlabor

    41、atory studies were run in which randomly drawn test specimens of two materialswere tested for moisture sorption. The density of the two materials was 16 kg/m3 1 lb/ft3) and 50 kg/m3 3.2 lb/ft3. Practice E691C1104/C1104M 13a3was followed for the design and analysis of the data. all oof the test speci

    42、mens were provided by a single laboratory. the detailsare given in ASTM Research Report NO. C1610243.12.2 Test Results The precision information given below in units of measurements noted is for the comparision of test results.12.1 Precision:Interlaboratory Test ProgramLight DensityMineral FiberHeav

    43、yDensityMineral FiberNumber of Laboratories 3 3Sorption by Weight, Average Value 2.1% 0.9%95% repeatability limit (within laboratory) 0.60% 0.18%95% reproducibility limit (betweenlaboratories)0.88% 0.52%Sorption by Volume, Average Value 0.03% 0.05%95% repeatability limit (within laboratory) 0.01% 0.

    44、01%95% reproducibility limit (betweenlaboratories)0.02% 0.03%Interlaboratory studies were run in which randomly drawn test specimens of two materials were tested for moisture sorption.The density of the two materials was 16 kg/m3 1 lb/ft3) and 50 kg/m3 3.2 lb/ft3. Practice E691 was followed for the

    45、designand analysis of the data. All of the test specimens were provided by a single laboratory. The details are given in ASTM Re-search Report No. RR:C16-1024.312.1.1 Test ResultsThe precision information given below in units of measurements noted is for the comparision of testresults.12.1.2 Precisi

    46、on:Light DensityMineral FiberHeavyDensityMineral FiberNumber of Laboratories 3 3Sorption by Weight, Average Value 2.1% 0.9%95% repeatability limit (within laboratory) 0.60% 0.18%95% reproducibility limit (betweenlaboratories)0.88% 0.52%Sorption by Volume, Average Value 0.03% 0.05%95% repeatability l

    47、imit (within laboratory) 0.01% 0.01%95% reproducibility limit (betweenlaboratories)0.02% 0.03%12.2 The precision of this test method is based on an interlaboratory study of Test Method C1104/C1104M, Standard TestMethod for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation, con

    48、ducted in 2012. Six laboratoriesparticipated in the study, testing three types of fiber insulation. Every analyst was instructed to report triplicate test results in thisstudy. Practice E691 was followed for the study design; the details are given in ASTM Research Report No. RR:C16-1041.512.2.1 Repe

    49、atability limit (r)Two test results obtained within one laboratory shall be judged not equivalent if they differ bymore than the “r” value for that material; “r” is the interval representing the critical difference between two test results for the samematerial, obtained by the same operator using the same equipment on the same day in the same laboratory.12.2.1.1 Repeatability limits are listed in Tables 1-3.12.2.2 Reproducibility limit (R)Two test results shall be judged not equivalent if they differ by


    注意事项

    本文(ASTM C1104 C1104M-2013a Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation《测定未覆面矿物纤维绝缘材料水蒸汽吸收性的标准试验方法》.pdf)为本站会员(dealItalian200)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开