欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B946-2006(2010) Standard Test Method for Surface Finish of Powder Metallurgy (P M) Products《粉末冶金(P M)产品的表面抛光的标准试验方法》.pdf

    • 资源ID:462873       资源大小:78.76KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B946-2006(2010) Standard Test Method for Surface Finish of Powder Metallurgy (P M) Products《粉末冶金(P M)产品的表面抛光的标准试验方法》.pdf

    1、Designation: B946 06 (Reapproved 2010)Standard Test Method forSurface Finish of Powder Metallurgy (PM) Products1This standard is issued under the fixed designation B946; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l

    2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers measuring the surface finish ofpowder metallurgy (PM) products at all stages of manufactur-ing

    3、from green compact to fully hardened finished component.1.2 This test method provides the definition and schematicof some common surface finish parameters (Ra,Rt, and Rz ISO)1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconve

    4、rsions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practice

    5、s and to determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 MPIF Standard:2MPIF Standard 58 Method for Determination of SurfaceFinish of Powder Metallurgy Products3. Significance and Use3.1 The surface finish of a component may be critical forcertain applica

    6、tions, affecting properties such as wear resis-tance, fatigue strength, and coefficient of friction.3.2 Surface finish may also be critical for componentassembly or system performance. Dimensional fit and matingsurface interaction may require certain surface finish require-ments to meet performance

    7、specifications.4. Interferences4.1 Because many conventional PM materials contain openporosity at the surface, special consideration should be takenwhen measuring surface finish.4.2 The use of a conical point stylus may result in inaccurateor inconsistent surface finish results because the sharper p

    8、ointof the stylus may drop into open porosity on the surface of thecomponent.4.3 A chisel point stylus may be used for better accuracyand consistency.4.4 Because the direction of pressing may cause direction-ality in surface finish values, the direction of measurementshould be specified and reported

    9、.5. Apparatus5.1 Surface finish measuring instrument.5.2 StylusChisel point, 0.050 in. (1.27 mm) length and0.0004 in. 6 30 % (0.010 mm 6 30 %) tip radius as shown inFig. 1. To limit the possibility of the stylus dropping into opensurface porosity, a chisel point stylus is recommended. If acone stylu

    10、s is used, filtering software shall also be used toremove the influence of open surface porosity.6. Sampling, Test Specimens, and Test Units6.1 The test surface shall be clean and free of any oil, dirt,debris, or foreign material.6.2 Sufficient surface area shall be available to permitmultiple trave

    11、rses by the measuring instrument.6.3 The test surface shall be flat over a sufficient length (inaccordance with instrument instructions) to allow propermovement of the stylus.7. Procedure7.1 The PM parts manufacturer and purchaser shall agree onthe desired location and direction for surface finish m

    12、easure-ment.7.2 Place the surface finish instrument in a position suitablefor measuring the test sample.7.3 Zero and verify the instrument over the surface finishrange expected for the test sample.7.4 Place the test sample under the stylus and then lower thestylus to the measuring position in accord

    13、ance with theinstrument instructions.7.5 Measure the surface finish of the test surface. A mini-mum of three traverses at different locations is recommended.1This test method is under the jurisdiction of ASTM Committee B09 on MetalPowders and Metal Powder Products and is the direct responsibility of

    14、 Subcom-mittee B09.05 on Structural Parts.Current edition approved Dec. 1, 2010. Published December 2010. Originallypublished 2006. DOI: 10.1520/B0946-06R10.2Metal Powder Industries Federation, 105 College Rd. East, Princeton, NJ08540-6692 U.S.A.1Copyright ASTM International, 100 Barr Harbor Drive,

    15、PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Report8.1 Report the surface finish to the nearest whole number inmicroinches (micrometres). Unless otherwise indicated, thesurface finish shall be Ra(average surface roughness) (see Fig.2). Depending on the type of instrument being use

    16、d, othersurface finish measures may also be reported.NOTE 1Rtis the maximum peak-to-valley height over the testedlength (absolute value between the highest and lowest peaks) as shown inFig. 3. Rzis the ten-point height or the absolute value of the five highestpeaks and five lowest valleys over the e

    17、valuation length as shown in Fig.4. Rzis also known as the ISO ten-point height parameter.8.2 If it has been specified, report the direction of measure-ment with respect to the pressing direction.9. Precision and Bias9.1 PrecisionAn interlaboratory study to determine theprecision of this test method

    18、 is currently under development.9.2 BiasNo information can be presented on the bias ofthe procedure in Test Method B946 for measuring surfacefinish because no material having an accepted reference valueis available.10. Keywords10.1 PM; powder metallurgy; powder metallurgy parts;stylus; surface finis

    19、h; surface roughnessNote 1The stylus is chisel shaped and has a standard radius on the edge andis 0.050 in. (1.27 mm) wide so that it will not drop into the porosity of the P/Msurface and give a false reading by measuring the cavities.FIG. 1 Chisel Stylus for Surface Finish MeasurementNote 2The arit

    20、hmetic average value of filtered roughness profile determinedfrom deviations about the centerline within the evaluation length lm.FIG. 2 RaArithmetic Mean Roughness ValueNote 3The maximum peak-to-valley height of the filtered profile over theevaluation length lm, irrespective of the sampling lengths

    21、 le.FIG. 3 RtMaximum Peak-to-Valley HeightB946 06 (2010)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such paten

    22、t rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited eithe

    23、r for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair he

    24、aring you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standar

    25、d may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).Note 4The average height difference between the five highest peaks and five lowest valleys contained within a chosen evaluation length.FIG. 4 RzISOTen-Point HeightB946 06 (2010)3


    注意事项

    本文(ASTM B946-2006(2010) Standard Test Method for Surface Finish of Powder Metallurgy (P M) Products《粉末冶金(P M)产品的表面抛光的标准试验方法》.pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开