欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf

    • 资源ID:462215       资源大小:55.05KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf

    1、Designation: B77 07 (Reapproved 2013)Standard Test Method forThermoelectric Power of Electrical-Resistance Alloys1This standard is issued under the fixed designation B77; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of

    2、last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the ther-moelectric power of a metal or alloy with respect to copperwhen

    3、the temperatures of the junctions lie between 0 and100C.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not pu

    4、rport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer

    5、, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B3 Specification for Soft or Annealed Copper Wire3. Terminology3.1 thermoelectric power, Q, nthe electromotive force inan electric c

    6、ircuit consisting of two metals when the junctionsbetween them have a difference in temperature of 1C.3.1.1 DiscussionExperimentally, it has been found thatthe thermoelectric power of two metals is not a constant butdepends on the mean temperature of the junctions. However,over a range of temperatur

    7、e from 0 to 100C it is usuallysufficient to assume that the thermoelectric power is indepen-dent of temperature so that for this range of temperature:Q 5 E/t2t!where:E = the electromotive force developed in the circuit,t = the higher temperature at one junction, C, andt = the lower temperature at th

    8、e other junction, C.4. Significance and Use4.1 The purpose of this method is to determine the suitabil-ity of different metals for use in resistance apparatus in whicha low thermoelectric power is desired. As most electric circuitsare largely composed of copper, the thermoelectric power of aresistan

    9、ce metal will generally be measured against copper.5. Test Specimen5.1 The metal or alloy to be tested shall be in the form ofsheet, ribbon, or wire and the test specimen shall be of suchlength that the two ends can be readily maintained at differenttemperatures. At each end of the specimen a copper

    10、 lead ofconvenient size shall be fastened. These leads shall make goodelectrical contact with the specimen, such as that obtained bywelding, brazing, or soldering. Slight impurities in the copperhave a negligible effect on the thermoelectric power.NOTE 1When necessary to specify the quality of the c

    11、opper leads,reference should be made to Specification B3.6. Procedure6.1 Measurement of TemperatureAs a matter ofprecaution, the average temperature used in determining thethermoelectric power shall be approximately the same as thatto which the material will be subjected in practice, and in nocase s

    12、hall the temperature difference between the two junctionsbe less than 20C. The temperature at each of two junctionsshall be measured by a device that is sufficiently accurate todetermine the temperature difference within 5 %. A convenientmethod for determining the temperatures of the junctions is to

    13、immerse each junction in separate oil baths maintained at thedesired temperatures. Baths that are stirred and the tempera-tures of which are thermostatically controlled are to bepreferred. However, beakers of oil which are supported byblocks of metal, sand baths, or other means may be used,provided

    14、the thermal capacity of these assemblies is such thatwhen the heat is cut off their temperatures will decrease at ratesless than 0.2C/min. The temperature of the oil in each bathmay be determined by a calibrated temperature measuring1This test method is under the jurisdiction of ASTM Committee B02 o

    15、nNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.10 on Thermostat Metals and Electrical Resistance Heating Materials.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1930. Last previous edition approved in 2007 as B77 07. DOI:10.1520/B0

    16、077-07R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive

    17、, PO Box C700, West Conshohocken, PA 19428-2959. United States1device of suitable precision and accuracy. If the oil is notstirred, the junctions shall be placed in close proximity to thetemperature-measuring instrument. To ensure that the tempera-tures of the junctions shall not be influenced by he

    18、at ofconduction along the specimen, the length of each specimenfrom the junction to the point where it leaves the surface of theoil shall not be less than 10 times the minimum cross-sectiondimension of the resistance material, nor less than 100 timesthe minimum cross section of the copper leads, and

    19、 in no caseless than 2 in. (50.8 mm).6.2 Measurement of Electromotive ForceThe electromo-tive force shall be determined by a method that will give thevalue correct within 5 %. Three different methods of measuringthe electromotive force are in common use, namely:6.2.1 The method in which a potentiome

    20、ter is used tocompare the unknown emf with that of a standard cell.6.2.2 The method in which the unknown emf is equated tothe difference of potential between the terminals of a standardresistor when a measured current flows through it.6.2.3 The method in which the emf is measured by thedeflection of

    21、 a suitable measuring instrument.6.2.4 In any case, precautions shall be taken to ensure thatthere are no parasitic electromotive forces in the measuringcircuit, a condition which may be determined by placing bothjunctions in the same beaker, in which case no appreciableelectromotive force shall be

    22、indicated.7. Polarity of the Metal7.1 The metal or alloy tested shall be considered to havepositive polarity when, in a circuit consisting of copper and themetal or alloy, the direction of current flow in the metal or alloyis from the junction having the higher temperature to the onehaving the lower

    23、 temperature.8. Report8.1 The report shall include the following:8.1.1 The character of the metal or alloy tested and theidentification of the specimen,8.1.2 The size, shape, and length of the specimen,8.1.3 Method of determining the temperatures of thejunctions,8.1.4 The temperature at each junctio

    24、n in degree Celsius,8.1.5 The type of apparatus used in measuring the electro-motive force,8.1.6 The observed electromotive force,8.1.7 The thermoelectric power, and8.1.8 The polarity of the metal or alloy tested.9. Precision and Bias9.1 The reproducibility of the test results depends on thecontrol

    25、used in making the connections and the control oftemperatures at the junctions. The bias will depend on theparameters listed for reproducibility and instrumentation usedto measure emf.9.2 The precision of this test method should be 1 % or less.9.3 The bias of this test method is within 6 %.10. Keywo

    26、rds10.1 copper; electrical resistant alloys; potentiometer; ther-moelectric powerASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the va

    27、lidity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your co

    28、mments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments hav

    29、e not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple

    30、 copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).B77 07 (2013)2


    注意事项

    本文(ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf)为本站会员(appealoxygen216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开