欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B653 B653M-2006 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接锆及锆合金锻造配件标准规范》.pdf

    • 资源ID:461876       资源大小:72.93KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B653 B653M-2006 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接锆及锆合金锻造配件标准规范》.pdf

    1、Designation: B 653/B 653M 06Standard Specification forSeamless and Welded Zirconium and Zirconium AlloyWelding Fittings1This standard is issued under the fixed designation B 653/B 653M; the number immediately following the designation indicates the yearof original adoption or, in the case of revisio

    2、n, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers fittings, factory made fromthree grades of zirconium and zirconium alloys. T

    3、he termwelding fittings applies to butt-welding parts such as 45 and90 elbows, 180 returns, caps, tees, reducers, lap-joint stubends, and other types.1.2 The values stated in either inch-pound units or SI unitsare to be regarded separately as the standard. Within the text,the SI units are shown in b

    4、rackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.1.3 This standard does not purport to address all of thesafety concerns, if any

    5、, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B 493 Specification for Zirconium and Zirconium All

    6、oyForgingsB 523/B 523M Specification for Seamless and Welded Zir-conium and Zirconium Alloy TubesB 550/B 550M Specification for Zirconium and ZirconiumAlloy Bar and WireB 551/B 551M Specification for Zirconium and ZirconiumAlloy Strip, Sheet, and PlateB 614 Practice for Descaling and Cleaning Zircon

    7、ium andZirconium Alloy SurfacesB 658/B 658M Specification for Seamless and Welded Zir-conium and Zirconium Alloy Pipe2.2 ANSI Standards:B16.9 Wrought Steel Butt-Welding Fittings3B36.19 Stainless Steel Pipe32.3 Manufacturers Standardization Society of the Valveand Fittings Industry Standards:SP-25 St

    8、andard Marking System for Valves, Fittings,Flanges, and Unions4SP-43 Standard Practice for Light Weight Stainless SteelFittings42.4 American Society of Mechanical Engineers:ASME Boiler and Pressure Vessel Code, Sections VIII andIX53. Terminology3.1 Lot Definitions:3.1.1 weld fittings, ndefinition is

    9、 to be mutually agreedupon between manufacturer and the purchaser.4. Classification4.1 The fittings are furnished in three grades as follows:4.1.1 Grade R60702 (PZ 2)Unalloyed zirconium.4.1.2 Grade R60704 (PZ 4)Zirconium-tin.4.1.3 Grade R60705 (PZ 5)Zirconium-niobium.5. Ordering Information5.1 Order

    10、s for materials under this specification shall in-clude the following information:5.1.1 Quantity,5.1.2 Name of material (zirconium fittings),5.1.3 Grade number (see 4.1),5.1.4 ASTM designation and year of issue,5.1.5 Hydrostatic test requirements (see 10.2),5.1.6 Inspection requirements (see 11.1),5

    11、.1.7 Finish (see Section 9), and5.1.8 Additions to the specification and supplementary re-quirements, if required.NOTE 1A typical ordering description is as follows: 15 pieces,1This specification is under the jurisdiction of ASTM Committee B10 onReactive and Refractory Metals and Alloys and is the d

    12、irect responsibility ofSubcommittee B10.02 on Zirconium and Hafnium.Current edition approved Sept. 1, 2006. Published September 2006. Originallyapproved in 1979. Last previous edition approved in 2002 as B 653/B 653M 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact

    13、ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.4Available from Manufacturers Stan

    14、dardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.5Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box

    15、C700, West Conshohocken, PA 19428-2959, United States.zirconium, 4-in. 100 mm, Schedule 40, 90 long radius elbows, descaled,ASTM B 653 - 01, Grade R60702. Supplementary Requirement S3, StressRelief Heat Treatment.6. Materials and Manufacture6.1 Forging, forming, or shaping operations may be per-form

    16、ed by hammering, pressing, piercing, extruding, upsetting,rolling, bending, fusion welding, machining, or by a combina-tion of these operations. The forming procedure shall be soapplied that it will not produce injurious defects in the fittings.6.2 Fittings containing welded seams or other joints ma

    17、deby welding shall comply with the following provisions:6.2.1 Welded by welders, welding operators, and weldingprocedures qualified under the provisions of Section IX of theASME Boiler and Pressure Vessel Code.6.2.2 Filler metal, when used, shall be the same grade as thebase metal.6.2.3 All welds on

    18、 grade R60705 shall be stress reliefannealed within 14 days after welding to prevent delayedhydride cracking, in accordance with Supplementary Require-ments Section S3, Stress Relief Heat Treatment.7. Chemical Composition7.1 The material shall conform to the requirements as tochemical composition pr

    19、escribed in Table 1.8. Tensile Requirements8.1 The material shall conform to the requirements as to thetensile properties prescribed in Table 1.9. Workmanship, Finish, and Appearance9.1 For fittings covered by ANSI B16.9 or MSS SP-43,orfor fittings to be used with pipe ordered to ANSI B36.19, thesiz

    20、es, shapes, and dimensions of the fittings shall be asspecified in those standards.9.2 The fittings shall be free of injurious external andinternal imperfections of a nature that will interfere with thepurpose for which the fittings are intended. Minor defects maybe removed by grinding, providing th

    21、e wall thickness is notdecreased to less than the minimum thickness, and furtherprovided that the ground-out area shall be faired out.10. Hydrostatic Tests10.1 All fittings shall be capable of withstanding withoutfailure, leakage, or impairment of their serviceability, a testpressure prescribed in t

    22、he applicable standards in Table 1 forthe pipe or tubing with which the fitting is planned to be used.10.2 Hydrostatic tests shall be performed when required bythe purchase order.11. Inspection11.1 The manufacturer shall inspect the material covered bythis specification prior to shipment. If so spec

    23、ified in thepurchase order, the purchaser or his representative may witnessthe testing and inspection of the material at the place ofmanufacture. In such cases the purchaser shall state in hispurchase order which tests he desires to witness. The manu-facturer shall give ample notice to the purchaser

    24、 as to the timeand place of the designated tests. If the purchasers represen-tative does not present himself at the time agreed upon for thetesting, the manufacturer shall consider the requirement for thepurchasers inspection at the place of manufacture to bewaived.11.2 The manufacturer shall afford

    25、 the inspector represent-ing the purchaser, without charge, all reasonable facilities tosatisfy him that the material is being furnished in accordancewith this specification. This inspection shall be so conducted asnot to interfere unnecessarily with the operation of the works.12. Rejection12.1 Reje

    26、ction for failure of the material to meet therequirements of this specification shall be reported to themanufacturer. Unless otherwise specified, rejected materialmay be returned to the manufacturer at the manufacturersexpense, unless the purchaser receives, within three weeks ofthe notice of reject

    27、ion, other instructions for disposition.13. Certification13.1 A producer or supplier shall furnish the purchaser witha certificate that the material was manufactured, sampled,tested, and inspected in accordance with this specification andhas been found to meet the requirements. The certificate shall

    28、include a report of the test results.13.2 All material incorporated within the fitting shall beidentified and shall be in accordance with the applicablestandards in Table 1.14. Referee14.1 In the event of disagreement between the manufacturerand the purchaser on the conformance of the material to th

    29、erequirements of this specification or any special test specifiedby the purchaser, a mutually acceptable referee shall performthe tests in question. The results of the referees testing shall beused in determining conformance of the material to thisspecification.15. Product Marking15.1 Unless otherwi

    30、se specified, the manufacturers nameor trademark, the schedule number, material, and size shall beTABLE 1 Permissible Raw MaterialsGradeAProduct and ASTM DesignationPipe Tube Plate Bar ForgingPZ 2(R60702)B 658/B 658MGrade R60702B 523/B 523MGrade R60702B 551/B 551MGrade R60702B 550/B 550MGrade R60702

    31、B 493Grade R60702PZ 4(R60704)B 658/B 658MGrade R60704B 523/B 523MGrade R60704B 551/B 551MGrade R60704B 550/B 550MGrade R60704B 493Grade R60704PZ 5(R60705)B 658/B 658MGrade R60705B 523/B 523MGrade R60705B 551/B 551MGrade R60705B 550/B 550MGrade R60705B 493Grade R60705AWhen fittings are of welded cons

    32、truction, the symbol shown shall be supplemented by the letter “W.”B 653/B 653M 062stamped (see Note 2), stenciled, electroetched, or otherwisesuitably marked on each fitting. In addition, each fitting shallbe marked with the identification grade symbol and suffix forthe respective specification lis

    33、ted in Table 1. On wall thick-nesses thinner than Schedule 40S, no stamps or other indentedmarkings shall be used. When the size does not permitcomplete marking, identification marks may be omitted in thesequence shown in MSS SP-25.NOTE 2When steel stamps are used, they should be applied prior tohea

    34、t treatment and care should be taken so that the marking is not deepenough to cause cracks or to reduce the wall thickness of the fitting belowthe minimum allowed.16. Packaging and Package Marking16.1 The fittings shall be packaged suitably in such amanner as to assure safe delivery to its destinati

    35、on whenproperly transported by common carrier.17. Keywords17.1 fitting; pipe; zirconium; zirconium alloySUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not be considered unless specified in the order, in which event thetest shall be made by the manufacturer at the purchasers expense.S1. S

    36、urface InspectionS1.1 Liquid penetrant inspection may be performed on alloutside-diameter surfaces of the fittings and inside-diametersurfaces where practicable. Acceptance shall be in accordancewith Appendix 8, Section VIII of the ASME Boiler andPressure Vessel Code.S2. Radiographic Inspections of

    37、WeldsS2.1 Radiographic inspection may be performed on allweldments of the fittings in accordance with paragraph UW-51,Section VIII, of the ASME Boiler and Pressure Vessel Code.S3. Stress-Relief Heat TreatmentS3.1 The stress-relieving treatment shall consist of holdingthe fitting at a minimum tempera

    38、ture of 1100F 600C for notless than12 h/in. 25 mm of the maximum thickness in anonreducing atmosphere.S3.2 The minimum time at this temperature is 15 min. Allstress-relieved parts shall be cleaned subsequently and shall befree of oxide scale contamination (see Practice B 614).ASTM International take

    39、s no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own res

    40、ponsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be address

    41、ed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the

    42、 address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).B 653/B 653M 063


    注意事项

    本文(ASTM B653 B653M-2006 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接锆及锆合金锻造配件标准规范》.pdf)为本站会员(brainfellow396)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开