欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B568-1998(2014) Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry《用X射线光度法测量镀层厚度的标准试验方法》.pdf

    • 资源ID:461592       资源大小:124.90KB        全文页数:8页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B568-1998(2014) Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry《用X射线光度法测量镀层厚度的标准试验方法》.pdf

    1、Designation: B568 98 (Reapproved 2014)Standard Test Method forMeasurement of Coating Thickness by X-Ray Spectrometry1This standard is issued under the fixed designation B568; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

    2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test method covers the

    3、use of X-ray spectrometry todetermine thickness of metallic and some nonmetallic coatings.1.2 The maximum measurable thickness for a given coatingis that thickness beyond which the intensity of the character-istic secondary X radiation from the coating or the substrate isno longer sensitive to small

    4、 changes in thickness.1.3 This test method measures the mass of coating per unitarea, which can also be expressed in units of linear thicknessprovided that the density of the coating is known.1.4 Problems of personnel protection against radiation gen-erated in an X-ray tube or emanating from a radio

    5、isotopesource are not covered by this test method. For information onthis important aspect, reference should be made to currentdocuments of the National Committee on Radiation Protectionand Measurement, Federal Register, Nuclear RegulatoryCommission, National Institute of Standards and Technology(fo

    6、rmerly the National Bureau of Standards), and to state andlocal codes if such exist.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and

    7、 determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E135 Terminology Relating to Analytical Chemistry forMetals, Ores, and Related Materials2.2 International Standard:ISO 3497 Metallic CoatingsMeasurement of CoatingThicknessX-ray Spectromet

    8、ric Methods3. Terminology3.1 Definitions of technical terms used in this test methodmay be found in Terminology E135.4. Summary of Test Method4.1 ExcitationThe measurement of the thickness of coat-ings by X-ray spectrometric methods is based on the combinedinteraction of the coating and substrate wi

    9、th incident radiationof sufficient energy to cause the emission of secondary radia-tions characteristic of the elements composing the coating andsubstrate. The exciting radiation may be generated by an X-raytube or by certain radioisotopes.4.1.1 Excitation by an X-Ray TubeSuitable exciting radia-tio

    10、n will be produced by an X-ray tube if sufficient potential isapplied to the tube. This is on the order of 35 to 50 kV for mostthickness-measurement applications. The chief advantage ofX-ray tube excitation is the high intensity provided.4.1.2 Excitation by a Radioisotope Of the many availableradioi

    11、sotopes, only a few emit gamma radiations in the energyrange suitable for coating-thickness measurement. Ideally, theexciting radiation is slightly more energetic (shorter in wave-length) than the desired characteristic X rays. The advantagesof radioisotope excitation include more compact instrument

    12、a-tion essentially monochromatic radiation, and very low back-ground intensity. The major disadvantage of radioisotopeexcitation is the much lower intensities available as comparedwith X-ray tube sources. X-ray tubes typically have intensitiesthat are several orders of magnitude greater than radiois

    13、otopesources. Due to the low intensity of radioisotopes, they areunsuitable for measurements on small areas (less than 0.3 mmin diameter). Other disadvantages include the limited numberof suitable radioisotopes, their rather short useful lifetimes, andthe personnel protection problems associated wit

    14、h high-intensity radioactive sources.4.2 DispersionThe secondary radiation resulting from theexposure of an electroplated surface to X radiation usuallycontains many components in addition to those characteristicof the coating metal(s) and the substrate. It is necessary,therefore, to have a means of

    15、 separating the desired compo-nents so that their intensities can be measured. This can bedone either by diffraction (wavelength dispersion) or byelectronic discrimination (energy dispersion).1This test method is under the jurisdiction ofASTM Committee B08 on Metallicand Inorganic Coatings and is th

    16、e direct responsibility of Subcommittee B08.10 onTest Methods.Current edition approved May 1, 2014. Published May 2014. Originallyapproved in 1972. Last previous edition approved in 2009 as B568 98(2009). DOI:10.1520/B0568-98R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, o

    17、rcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.2.1 Wavelength D

    18、ispersionBy means of a single-crystalspectrogoniometer, wavelengths characteristic of either thecoating or the substrate may be selected for measurement.Published data in tabular form are available that relate spec-trogoniometer settings to the characteristic emissions of ele-ments for each of the c

    19、ommonly used analyzing crystals.4.2.2 Energy DispersionX-ray quanta are usually speci-fied in terms of their wavelengths, in angstroms (), or theirequivalent energies in kiloelectron volts (keV). The relation-ship between these units is as follows:keV!A! 5 12.396where:keV = the quantum energy in tho

    20、usands of electron volts, and = the equivalent wavelength in angstroms (10-10m).In a suitable detector (see 4.3.2), X rays of different energieswill produce output pulses of different amplitudes. Aftersuitable amplification, these pulses can be sorted on the basisof their amplitudes and stored in ce

    21、rtain designated channels ofa multichannel analyzer, each adjacent channel representing anincrement of energy. Typically, a channel may represent a spanof 20 eV for a lithium-drifted silicon detector or 150 to 200 eVfor a proportional counter. From six to sixty adjacent channelscan be used to store

    22、the pulses representing a selectedcharacteristic emission of one element, the number of channelsdepending on the width of the emission peak (usually displayedon the face of a cathode ray tube). The adjacent channels usedto store the pulses from the material under analysis are calledthe “region of in

    23、terest” or ROI.4.3 Detection:4.3.1 Wavelength Dispersive SystemsThe intensity of awavelength is measured by means of an appropriate radiationdetector in conjunction with electronic pulse-countingcircuitry, that is, a scaler. With wavelength dispersive systems,the types of detectors commonly used as

    24、the gas-filled typesand the scintillation detector coupled to a photomultiplier tube.4.3.2 Energy-Dispersive SystemsFor the highest energyresolution with energy dispersive systems, a solid-state devicesuch as the lithium-drifted silicon detector must be used. Thistype of detector is maintained at a

    25、very low temperature in aliquid-nitrogen cryostat (77K). Acceptable energy resolutionfor most thickness measurement requirements can be realizedwith proportional counters, and these detectors are being usedon most of the commercially available thickness gages basedon X-ray spectrometry. In setting u

    26、p a procedure for coating-thickness measurement using an energy-dispersive system,consideration should be given to the fact that the detector“sees” and must process not only those pulses of interest butalso those emanating from the substrate and from supportingand masking materials in the excitation

    27、 enclosure. Therefore,consideration should be given to restricting the radiation to thearea of interest by masking or collimation at the radiationsource. Similarly, the detector may also be masked so that itwill see only that area of the specimen on which the coatingthickness is to be determined.4.4

    28、 Basic PrincipleA relationship exists between coatingthickness and secondary radiation intensity up to the limitingthickness mentioned in 1.2. Both of the techniques describedbelow are based on the use of primary standards of knowncoating thicknesses which serve to correlate quantitatively theradiat

    29、ion intensity and thickness.4.5 Thickness Measurement by X-Ray EmissionIn thistechnique, the spectrogoniometer is positioned to record theintensity of a prominent wavelength characteristic of thecoating metal or, in the case of an energy-dispersive system,the multichannel analyzer is set to accept t

    30、he range of energiescomprising the desired characteristic emission. The intensity ofthe coatings X-ray emission (coating ROI) will be at aminimum for a sample of the bare substrate where it willconsist of that portion of the substrate fluorescence which mayoverlap the ROI of the coating and a contri

    31、bution due tobackground radiation. This background radiation is due to theportion of the X-ray tubes output which is the same energy asthe coatings X-ray emission. The sample will always scattersome of these X rays into the detector. If the characteristicemission energies of the coating and substrat

    32、e are sufficientlydifferent, the only contribution of the substrate will be due tobackground. For a thick sample of the solid coating metal orfor an electroplated specimen having an “infinitely thick”coating, the intensity will have its maximum value for a givenset of conditions. For a sample having

    33、 a coating of less than“infinite” thickness, the intensity will have an intermediatevalue. The intensity of the emitted secondary X radiationdepends, in general, upon the excitation energy, the atomicnumbers of the coating and substrate, the area of the specimenexposed to the primary radiation, the

    34、power of the X-ray tube,and the thickness of the coating. If all of the other variables arefixed, the intensity of the characteristic secondary radiation isa function of the thickness or mass per unit area of the coating.The exact relationship between the measured intensity and thecoating thickness

    35、must be established by the use of standardshaving the same coating and substrate compositions as thesamples to be measured. The maximum thickness that can bemeasured by this method is somewhat less than what is,effectively, infinite thickness. This limiting thickness depends,in general, upon the ene

    36、rgy of the characteristic X-ray and thedensity and absorption properties of the material under analy-sis. The typical relationship between a coating thickness andthe intensity of a characteristic emission from the coating metalis illustrated by the curve in the Appendix, Fig. X1.1.4.6 Thickness Meas

    37、urements by X-Ray AbsorptionIn thistechnique the spectrometer, in the case of a wavelength-dispersive system, is set to record the intensity of a selectedemission characteristic of the basis metal. In an energy-dispersive system, the multichannel analyzer is set to accumu-late the pulses comprising

    38、the same energy peak. The intensitywill be a maximum for a sample of the uncoated basis metaland will decrease with increasing coating thickness. This isbecause both the exciting and secondary characteristic radia-tions undergo attenuation in passing through the coating.Depending upon the atomic num

    39、ber of the coating, when thecoating thickness is increased to a certain value, the character-istic radiation from the substrate will disappear, although aB568 98 (2014)2certain amount of scattered radiation will still be detected. Themeasurement of a coating thickness by X-ray absorption is notappli

    40、cable if an intermediate coating is present because of theindeterminate absorption effect of intermediate layer. Thetypical relationship between coating thickness and the intensityof a characteristic emission from the substrate is shown in theAppendix, see Fig. X1.2.4.7 Thickness and Composition Mea

    41、surement by Simultane-ous X-ray Emission and Absorption (Ratio Method)It ispossible to combine the X-ray absorption and emission tech-niques when coating thicknesses and alloy composition aredetermined from the ratio of the respective intensities ofsubstrate and coating materials. Measurements by th

    42、is ratiomethod are largely independent of the distance between testspecimen and detector.4.8 Multilayer MeasurementsMany products have multi-layer coatings in which it is possible to measure each of thecoating layers by using the multiple-energy-region capabilityof the multichannel analyzer of an en

    43、ergy-dispersive system.The measuring methods permit the simultaneous measurementof coating systems with up to three layers. Or the simultaneousmeasurement of thickness and compositions of layers with upto three components. Such measurements require unique dataprocessing for each multilayer combinati

    44、on to separate thevarious characteristic emissions involved, to account for theabsorption by intermediate layers, and to allow for anysecondary excitation which may occur between layers. Typicalexamples of such combinations are gold on nickel on copperand nickel on copper on steel.4.9 Mathematical D

    45、econvolutionWhen using a multi-channel analyzer a mathematical deconvolution of the second-ary radiation spectra can be used to extract the intensities of thecharacteristic radiation. This method can be used when theenergies of the detected characteristic radiations do not differsufficiently (for ex

    46、ample, characteristic radiation from Au andBr). This method sometimes is described as numerical filteringin order to distinguish from the technique of setting fixedRegion of Interest (ROI) channel limits in the multichannelanalyzer.5. Significance and Use5.1 This is a sensitive, noncontact, and nond

    47、estructivemethod for measuring the coating thickness (and in somecases, coating composition) of metallic and some nonmetalliccoatings over a range of thicknesses from as little as 0.01 mto as much as 75 m depending on the coating and substratematerials. It can be used to measure coating and base com

    48、bi-nations that are not readily measured by other techniques.5.2 The coating thickness is an important factor in theperformance of a coating in service.6. Factors Affecting Accuracy6.1 Counting StatisticsThe production of X-ray quanta israndom with respect to time. This means that during a fixedtime

    49、 interval, the number of quanta emitted will not always bethe same. This gives rise to the statistical error which isinherent in all radiation measurements. In consequence, anestimate of the counting rate based on a short counting interval(for example, 1 or 2 s) may be appreciably different from anestimate based on a longer counting period, particularly if thecounting rate is low. This error is independent of other sourcesof error such as those arising from mistakes on the part of theoperator or from the use of inaccurate standards. To reduce thestatistica


    注意事项

    本文(ASTM B568-1998(2014) Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry《用X射线光度法测量镀层厚度的标准试验方法》.pdf)为本站会员(brainfellow396)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开