欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B394-2009 Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes.pdf

    • 资源ID:461124       资源大小:82.52KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B394-2009 Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes.pdf

    1、Designation: B394 09Standard Specification forNiobium and Niobium Alloy Seamless and Welded Tubes1This standard is issued under the fixed designation B394; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

    2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers wrought niobium and niobiumalloy seamless and welded tubes as follows:1.1.1 R04200-Type 1Reactor grade unal

    3、loyed niobium,1.1.2 R04210-Type 2Commercial grade unalloyed nio-bium,1.1.3 R04251-Type 3Reactor grade niobium alloy con-taining 1 % zirconium, and1.1.4 R04261-Type 4Commercial grade niobium alloycontaining 1 % zirconium.1.2 The values stated in inch-pound units are to be regardedas standard. The val

    4、ues given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following precautionary caveat pertains only to thetest methods portion of this specification. This standard doesnot purport to address all of the safety con

    5、cerns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2B391 Specification for Niobium and Niobium

    6、Alloy IngotsE8 Test Methods for Tension Testing of Metallic MaterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE2626 Guide for Spectrometric Analysis of Reactive andRefractory Metals3. Terminology3.1 Definitions of Terms Specific to This Standa

    7、rd:3.1.1 lot, na lot shall consist of all material produced fromthe same ingot at one time, with the same cross section,processed with the same nominal metallurgical parameters andheat treated at the same conditions.4. Ordering Information4.1 Orders for materials under this specification shall in-cl

    8、ude the following information as applicable:4.1.1 Type and grade (Section 1),4.1.2 ASTM designation and year of issue,4.1.3 Welding (Section 5),4.1.4 Quantity in weight, number of pieces, and dimensions,4.1.5 Chemistry (6.3),4.1.6 Temper designation (Section 8),4.1.7 Permissible variations in length

    9、 and quantity or weight(9.2, 9.4, and Table 1B),4.1.8 Quality and finish (10.4),4.1.9 Sampling (11.2),4.1.10 Hydrostatic or pneumatic test (14.2),4.1.11 Inspection (Section 15),4.1.12 Required reports (Section 17), and4.1.13 Additions to the specification and supplementaryrequirements, as required.5

    10、. Materials and Manufacture5.1 Material covered by this specification shall be madefrom ingots that conform to Specification B391 and that areproduced by vacuum or plasma arc melting, vacuum electron-beam melting, or a combination of these three methods.5.2 Seamless tubes may be made by any seamless

    11、 methodthat will yield a product meeting the requirements of thisspecification, such as, but not limited to, extrusion of billetswith subsequent cold working by drawing, swaging, or pilger-ing, with intermediate anneals, until the final dimensions arereached.5.3 Welded tubing shall be made from flat

    12、-rolled productsby an automatic or semiautomatic welding process with noaddition of filler metal in the welding operation. Other methodsof welding, such as the addition of filler metal or hand welding,may be employed if approved by the purchaser and tested bymethods agreed upon between the manufactu

    13、rer and the1This specification is under the jurisdiction of ASTM Committee B10 onReactive and Refractory Metals and Alloys and is the direct responsibility ofSubcommittee B10.03 on Niobium and Tantalum.Current edition approved Oct. 1, 2009. Published December 2009. Originallyapproved in 1989. Last p

    14、revious edition approved in 2003 as B394 - 03. DOI:10.1520/B0394-09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM w

    15、ebsite.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.purchaser. The manufacturer must use proper precautions toprevent contamination during welding.6. Chemical Requirements6.1 The niobium and niobium alloy ingots and billets forcon

    16、version to finished products covered by this specificationshall conform to the requirements for chemical composition asprescribed in Table 2.6.2 The manufacturers ingot analysis shall be consideredthe chemical analysis for products supplied under this specifi-cation, except for interstitials as spec

    17、ified in 6.3.Alternately, ananalysis of a representative sample of in process or finalproduct from the same ingot may be substituted.6.3 When requested by the purchaser at the time of pur-chase, the manufacturer shall furnish a report certifying thevalues of the interstitial elements (C, O, N, H) on

    18、 end productas prescribed in Table 3 for each lot of material supplied. Endproduct interstitial samples must be taken after all thermal andchemical processing.6.4 Guide E2626 is recommended as a guide, where appli-cable.7. Mechanical Requirements7.1 The annealed materials supplied under this specifi

    19、cationshall conform to the requirements for mechanical properties asspecified in Table 4.8. Temper Designations8.1 Unless otherwise stated, the materials supplied underthese specifications shall be in the fully annealed condition,that is, at least 90 % recrystallized.8.2 Other temper designations, s

    20、uch as cold-worked temperor stress-relieved temper, can be specified as agreed uponbetween the purchaser and the manufacturer at the time ofpurchase.TABLE 1 Permissible Variations in Diameter and Wall ThicknessMeasured at any LocationANominal Outside Diameter,in. (mm)BVariation inOutsideDiameter,Ove

    21、r andUnder, in.(mm)BVariation inInsideDiameter,Over andUnder, in.(mm)CVariation inWall Thickness,Over andUnder, %C,D0.187 to 0.625 (4.7 to 15.9), excl 0.004 (0.010) 0.004 (0.010) 100.625 to 1.000 (15.9 to 25.4), excl 0.005 (0.13) 0.005 (0.13) 101.000 to 2.000 (25.4 to 50.8), excl 0.0075 (0.19) 0.007

    22、5 (0.19) 102.000 to 3.000 (50.8 to 76.2), excl 0.010 (0.25) 0.010 (0.25) 103.000 to 4.000 (76.2 to 101.6), excl 0.0125 (0.32) 0.0125 (0.32) 10AThese tolerances are applicable to only two dimensions, such as outsidediameter and wall, or inside diameter and wall, or outside diameter and insidediameter

    23、.BFor applicable tolerances for very small tubes, less than 0.187 in. (4.9 mm) inoutside diameter, or very thin wall tubes, less than 0.010 in. (0.25 mm), theproducer should be consulted.CWhen tubes as ordered require wall thicknesses34 in. (19.05 mm) or over, oran inside diameter 60 % or less of th

    24、e outside diameter, a wider variation in wallthickness is required. On such sizes, a variation in wall thickness of 12.5 % overand under will be permitted.DOvality measured at any cross section: For tubes with nominal wall thicknessless than 3 % of the nominal outside diameter, the ovality tolerance

    25、 is double thetolerance shown in the second and third columns.TABLE 2 Chemical RequirementsElementType 1(ReactorGradeUnalloyedNiobium)R04200Type 2(CommercialGradeUnalloyedNiobium)R04210Type 3(Reactor GradeNiobium1 %Zirconium)R04251Type 4(CommercialGradeNiobium1 %Zirconium)R04261Max Weight % (Except

    26、Where Otherwise Specified)Each ingot:Carbon 0.01 0.01 0.01 0.01Nitrogen 0.01 0.01 0.01 0.01Oxygen 0.015 0.025 0.015 0.025Hydrogen 0.0015 0.0015 0.0015 0.0015Zirconium 0.02 0.02 0.8 to 1.2(range)0.8to1.2(range)Tantalum 0.1 0.3 0.1 0.5Iron 0.005 0.01 0.005 0.01Silicon 0.005 0.005 0.005 0.005Tungsten 0

    27、.03 0.05 0.03 0.05Nickel 0.005 0.005 0.005 0.005Molybdenum 0.010 0.020 0.010 0.050Hafnium 0.02 0.02 0.02 0.02Titanium 0.02 0.03 0.02 0.03When specified:Boron 2 ppm . 2 ppm .Aluminum 0.002 0.005 0.002 0.005Beryllium 0.005 . 0.005 .Chromium 0.002 . 0.002 .Cobalt 0.002 . 0.002 .TABLE 3 Additional Chemi

    28、cal Requirements for FinishedProduct (When Specified by Purchaser)ElementType 1(Reactor GradeUnalloyedNiobium)R04200Type 2(CommercialGradeUnalloyedNiobium)R04210Type 3(Reactor GradeNiobium1 %Zirconium)R04251Type 4(CommercialGradeNiobium1 %Zirconium)R04261Max Weight %Oxygen 0.0250 0.0400 0.0250 0.040

    29、0Carbon 0.0100 0.0150 0.0100 0.0150Nitrogen 0.0100 0.0100 0.0100 0.0100Hydrogen 0.0015 0.0015 0.0015 0.0015B394 0929. Permissible Variations in Dimensions and Weight9.1 Diameter and Wall ThicknessThe permissible varia-tions in diameter and wall thickness of the tubes shall notexceed those prescribed

    30、 in Table 1.9.2 LengthWhen tube is ordered cut to length, the useablelength shall not be less than that specified, but a variation of+18 in. (3.18 mm) will be permitted for lengths up to 6 ft (1.8m). For lengths over 6 ft, a variation of +14 in. (6.4 mm) willbe permitted, unless otherwise specified

    31、at the time of pur-chase.9.3 StraightnessThe tube shall be free of bends or kinks,and the maximum bow shall not exceed values shown in Table5.9.4 Quantity or WeightFor orders requiring up to 100 ft(30.5 m) of finished tubing, the manufacturer may overship by20 %. When the order is for quantities up

    32、to 1000 ft (305 m) or1000 lb (453.6 kg), the manufacturer may overship by 10 %.The permissible overshipment shall be negotiated for orderslarger than this quantity.10. Quality and Finish10.1 Finished niobium and niobium alloy tubes shall be freeof injurious internal and external imperfections of a n

    33、ature thatwill interfere with the purpose for which it was intended.10.2 The finished tubes shall be visibly free of oxide,grease, oil, residual lubricants, and other extraneous materials.10.3 The finished tubes shall be free of cracks, seams,slivers, burrs, blisters, and other injurious imperfectio

    34、ns ex-ceeding 10 % of the nominal wall thickness.10.4 Methods of testing for these defects and standards ofacceptability shall be as agreed upon between the manufacturerand the purchaser.11. Sampling11.1 Samples for chemical and mechanical testing shall betaken from the finished material after all m

    35、etallurgical process-ing to determine conformity to this specification. The samplesmay be taken prior to final inspection and minor surfaceconditioning by abrasion and pickling, and shall be represen-tative of the finished product.11.2 Care shall be exercised to ensure that the sampleselected for te

    36、sting is representative of the material and that itis not contaminated by the sampling procedure. If there is anyquestion relating to the sampling technique or the analysisthereof, the methods of sampling and analysis shall be asagreed upon between the purchaser and the manufacturer.12. Number of Te

    37、sts and Retests12.1 Two samples from each lot of tubes shall be tested forflare and tensile properties in the longitudinal direction.12.2 When hydrostatic or pneumatic testing is required, alltubes in the lot shall be tested.12.3 If end-product chemical tests are required (6.3), onechemical test sha

    38、ll be made from each lot of finished product.12.4 RetestsIf any sample or specimen exhibits obvioussurface contamination or improper preparation, disqualifying itas a truly representative sample, it shall be discarded and a newsample or specimen substituted.12.4.1 In case of a failure, retest two ad

    39、ditional specimens.If both retest specimens conform to this specification, discardthe original values and consider the material acceptable;otherwise, the lot shall be rejected or reworked and tested.12.5 If the results of the final tube inspections are not inconformance with the requirements of this

    40、 specification, the lotmay be reworked at the option of the manufacturer. The lotshall be acceptable if results of all tests, after reworking,conform to this specification.13. Significance of Numerical Limits13.1 For the purposes of determining compliance with thespecified limits for requirements of

    41、 the properties listed in thisspecification, an observed value or a calculated value shall berounded as indicated in accordance with the rounding methodof Practice E29.14. Test Methods14.1 Tension TestConduct tension tests in accordancewith Test Methods E8. Determine the yield strength by the0.2 % o

    42、ffset method. Small size, 1-in. (25.4-mm) gage lengthspecimens proportional to the standard specimen can be used.Determine tensile properties using a strain rate of 0.003 to0.007 in./in.min (mm/mmmin) through the yield point. Afterthe yield strength has been exceeded, increase the cross-headspeed to

    43、 approximately 0.05 in./in.min (mm/mmmin) tofailure.14.2 Hydrostatic and Pneumatic TestThese tests are op-tional. Should the purchaser require either or both of these testson finished tubular product, the requirement must be agreedupon at the time of purchase. The cost of this special provisionwill

    44、be negotiated between the purchaser and the manufacturerat the time of purchase. The procedure for the hydrostatic testis outlined in 14.2.1, and the procedure for the pneumatic testis outlined in 14.2.2. If both tests are specified by thepurchaser, the hydrostatic test will be done first.TABLE 4 Me

    45、chanical Properties for Material, Annealed Condition(90 % Minimum Recrystallized)GradeUltimateTensileStrength, min,psi (MPa)Yield Strength(0.2 % offset),min,psi (MPa)Elongation in1-in. (25-mm)gage length,min, %Type1welded18 000 (125) 10 500 (73) 25Type1seamless18 000 (125) 8500 (59) 25Type2welded18

    46、000 (125) 10 500 (73) 25Type2seamless18 000 (125) 8500 (59) 25Type 3 28 000 (195) 18 000 (125) 20Type 4 28 000 (195) 18 000 (125) 20TABLE 5 StraightnessLength, ft (m) Maximum Curvature Depth of ArcOver 3 to 6 (0.91 to 1.83), incl18 in. (3.2 mm)Over 6 to 8 (1.83 to 2.44), incl316 in. (4.8 mm)Over 8 t

    47、o 10 (2.44 to 3.05), incl14 in. (6.4 mm)Over 10 (3.05)14 in./any 10 ft (2.1 mm/m)B394 09314.2.1 Hydrostatic TestEach tube so tested shall with-stand without showing bulges, leaks, or other defects, aninternal hydrostatic pressure that will produce in the tube walla stress of 75 % of the minimum spec

    48、ified yield strength atroom temperature. This pressure shall be determined by thefollowing equation:P 5 2St/D(1)where:P = minimum hydrostatic pressure, psi (or MPa),S = allowable fiber stress of 75 % of the minimum yieldstrength, psi (or MPa),t = average wall thickness of the tube, in. (or mm), andD

    49、 = outside diameter of the tube, in. (or mm).Maintain the test pressure for at least 10 s.14.2.2 Pneumatic TestEach tube so tested shall withstandan internal air pressure of 100 psi (.7 MPa) minimum for aminimum of 5 s without showing evidence of leakage. The testmethod used, for example, placing the tube under water orusing the pressure differential method, shall permit easy visualdetection of any leakage. Any evidence of leakage shall because for rejection of that tube.14.3 FlareA section of the finished tube shall be capableof being flared witho


    注意事项

    本文(ASTM B394-2009 Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes.pdf)为本站会员(赵齐羽)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开