欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM A874 A874M-1998(2004) Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-Temperature Service.pdf

    • 资源ID:459800       资源大小:27.40KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM A874 A874M-1998(2004) Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-Temperature Service.pdf

    1、Designation: A 874/A 874M 98 (Reapproved 2004)Standard Specification forFerritic Ductile Iron Castings Suitable for Low-TemperatureService1This standard is issued under the fixed designation A 874/A 874M; the number immediately following the designation indicates the yearof original adoption or, in

    2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers ductile iron castings suitablefor service at temperatures

    3、 of 40F 40C and above.1.2 The values stated in either inch-pound or SI units are tobe regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each system are notexact equivalents; therefore, each system shall be used inde-pendently of the other. Comb

    4、ining values from the two systemsmay result in nonconformance with the specification.1.3 The following precautionary statement pertains only tothe test methods portion, Section 11, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its

    5、use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2A 247 Test Method for Evaluating the Microstructure ofGraphite in Iron Cast

    6、ingsE 8 Test Methods for Tension Testing of Metallic MaterialsE 30 Test Methods for Chemical Analysis of Steel, CastIron, Open-Hearth Iron, and Wrought Iron3E 59 Practice for Sampling Steel and Iron for Determinationof Chemical Composition3E 94 Guide for Radiographic ExaminationE 165 Test Method for

    7、 Liquid Penetrant ExaminationE 351 Test Methods for Chemical Analysis of Cast IronAll TypesE 562 Test Method for Determining Volume Fraction bySystematic Manual Point CountE 689 Reference Radiographs for Ductile Iron CastingsE 709 Guide for Magnetic Particle Examination3. Ordering Information3.1 Ord

    8、ers for material under this specification shall includethe following applicable information:3.1.1 Drawing, catalog number, or part identification,3.1.2 Quantity (weight or number of pieces),3.1.3 ASTM designation and year of issue,3.1.4 Marking instructions (see Section 15),3.1.5 Place of inspection

    9、 (see 13.1),3.1.6 Limits on residual elements (see 5.2),3.1.7 Visual and dimensional acceptance standard (see 7.1),3.1.8 Sampling plan (see Section 9), and3.1.9 Supplementary requirements.4. Materials and Manufacture4.1 Castings may be supplied either as cast or heat treatedand shall have essentiall

    10、y a ferritic structure that contains nomassive carbides.5. Chemical Composition5.1 The iron shall conform to the requirements for chemicalcomposition shown in Table 1.5.2 By agreement between the manufacturer and purchaser,analysis may be required and limits established for elementsnot specified in

    11、Table 1.6. Mechanical and Microstructural Properties6.1 Tensile PropertiesThe iron shall conform to the re-quirements for tensile properties shown in Table 2.6.2 MicrostructureGraphite contained in the microstruc-ture shall be evaluated in accordance with Test Method A 247.The percent of each graphi

    12、te type shall be estimated, and thetotal of all estimates shall equal 100 %. The total percent ofTypes 1 and 2 graphite shall be a minimum of 90 %.1This specification is under the jurisdiction of ASTM Committee A04 on IronCastings and is the direct responsibility of Subcommittee A04.02 on Malleable

    13、andDuctile Iron Castings.Current edition approved Oct. 1, 2004. Published October 2004. Originallyapproved in 1989. Last previous edition approved in 1998 as A 874/A 874M - 98.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. Fo

    14、r Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Workmanship, Finish, and Appearance7.1 The surface of th

    15、e casting shall be examined visuallyand shall be free from adhering sand, scale, cracks, and hottears. Other surface discontinuities shall meet visual anddimensional acceptance standards specified in the order.7.2 Conditioning of castings is permitted to the extent thatthe removal of metal does not

    16、extend into the envelope of thefinished container and does not alter the properties of the metalremaining in the finished container.8. Repair8.1 Castings shall not be repaired by plugging, welding,brazing, impregnation, or any other means.9. Sampling9.1 Test coupons will be obtained from the casting

    17、. Thelocation in the casting from which the test coupons areobtained and the number obtained from each location shall beagreed upon between the manufacturer and purchaser.9.2 Metallographic samples shall be obtained from the samelocation as the mechanical test coupons.9.3 Nondestructive examination

    18、methods for estimating mi-crostructure may be used to supplement the destructive exami-nation sampling plan.9.4 Sampling for chemical analysis shall be in accordancewith Practice E 59.9.4.1 The chemical analysis for total carbon shall be madeon either chilled cast pencil-type specimens or thin wafer

    19、sapproximately132 in. 0.8 mm thick cut from test coupons.10. Number of Tests and Retests10.1 The number of tension tests and the number of micro-structural examinations shall be agreed upon between themanufacturer and purchaser.10.2 If any tension test specimen shows obvious defects, itmay be discar

    20、ded and another from the same coupon may betested.11. Test Methods11.1 Conduct the tension test in accordance with TestMethods E 8.11.2 Determine the yield strength using one of the followingmethods:11.2.1 The 0.2 % offset method, or11.2.2 Extension under load method where the yieldstrength may be d

    21、etermined as the stress producing an elonga-tion under load of 0.330 %, that is, 0.0066 in. 0.165 mm in agage length of 2 in. 50 mm.11.3 Determine the percent of each graphite nodule type bymanual coating, semi-automatic, or automatic image analysismethods. The manual count method shall prevail when

    22、 theresults of other methods differ. Magnification shall be at 100 3.11.4 Spectrometric methods may be used for chemicalanalysis. Should a dispute arise concerning chemical compo-sition, use Test Methods E 351 and E 30 for referee methods.12. Records12.1 Records of the chemical composition, mechanic

    23、alproperties, and the metallographic examination shall be sys-tematically made and maintained.13. Inspection13.1 Unless otherwise specified in the contract or purchaseorder, the manufacturer shall perform all of the tests andinspections required by the specification.13.2 All tests and inspections sh

    24、all be made at the place ofmanufacture or a mutually agreed upon location.13.3 The inspector representing the purchaser shall haveentry at all times, while work on the contract of the purchaseris being performed, to all parts of the manufacturers worksthat concern the manufacture of the material ord

    25、ered. Themanufacturer shall afford the inspector all reasonable facilitiesto satisfy that the material is being furnished in accordancewith these specifications. The inspector representing the pur-chaser shall not interfere unnecessarily with the operation ofthe works.14. Certification14.1 The manuf

    26、acturers certification shall be furnished tothe purchaser stating the material was manufactured, sampled,tested, and inspected in accordance with this specification(including the year of issue) and was found to meet therequirement(s). In addition, a test report shall be included withthe certificatio

    27、n giving the results of all tests performedincluding chemical analysis.15. Product Marking15.1 The casting shall be identified and shall be marked inaccordance with instructions issued by the purchaser.TABLE 1 Chemical CompositionElement Minimum, % Maximum, %Total carbon 3.0 3.7Carbon equivalent (ca

    28、rbon +13 silicon) . . . 4.5Silicon 1.2 2.3Phosphorous . . . 0.03Magnesium . . . 0.07Manganese . . . 0.25Copper . . . 0.1Nickel . . . 1.0Chromium . . . 0.07TABLE 2 Tensile PropertiesTensile Strength,min, psi MPaYield Strength,min, psi MPaElongation in 2 in. 50 mm,min, %45 000 300 30 000 200 12 12A 87

    29、4/A 874M 98 (2004)2SUPPLEMENTARY REQUIREMENTSSupplementary requirements shall be applied only when specified by the purchaser. Details of thesupplementary requirements shall be agreed upon by the manufacturer and purchaser. The specifiedtests shall be performed by the manufacturer prior to shipment

    30、of the castings.S1. Magnetic Particle ExaminationS1.1 Castings shall be examined for surface discontinuitiesby magnetic particle examination. The examination shall be inaccordance with Guide E 709. The extent of examination andthe basis for acceptance shall be agreed upon between themanufacturer and

    31、 purchaser.S2. Ultrasonic ExaminationS2.1 Castings shall be examined for internal defects byultrasonic examination. The examination procedures and ac-ceptance criteria shall be agreed upon between the manufac-turer and purchaser.S3. Liquid Penetrant ExaminationS3.1 Castings shall be examined for sur

    32、face discontinuitiesby means of liquid penetrant examination. The examinationshall be in accordance with Test Method E 165. Areas to beinspected, methods and types of liquid penetrants to be used,developing procedure, and basis for acceptance shall be agreedupon between the manufacturer and purchase

    33、r.S4. Radiographic ExaminationS4.1 Castings shall be examined for internal defects bymeans of X rays or gamma rays. The procedure shall be inaccordance with Guide E 94, and types and degrees of discon-tinuities considered shall be judged by Reference RadiographsE 689. The extent of examination and b

    34、asis for acceptanceshall be agreed upon between the manufacturer and purchaser.S5. Fracture ToughnessS5.1 Fracture toughness testing shall be performed onsamples removed from the casting. The method of fracturetoughness testing, the location from which the samples areremoved, the number of tests per

    35、formed, and the acceptancerequirements shall be agreed upon between the manufacturerand purchaser.S6. Nodule CountS6.1 The nodule count per unit area shall be determined byexamining 100 3 micrographs.4The samples for the micro-graphs shall be removed from the casting at locations agreedupon. The ins

    36、pection method and the acceptance requirementsshall be agreed upon between the manufacturer and purchaser.Test Method E 562 may be used for guidance.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users

    37、 of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every f

    38、ive years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical

    39、 committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,

    40、PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).4Electric Power Research Institute Project 2813-1, “Relationships BetweenDuctile Iron Fracture Toughness and Microstructure, December 1986, providesbackground information.A 874/A 874M 98 (2004)3


    注意事项

    本文(ASTM A874 A874M-1998(2004) Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-Temperature Service.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开