欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM A820 A820M-2015 Standard Specification for Steel Fibers for Fiber-Reinforced Concrete《纤维增强混凝土用钢纤维的标准规格》.pdf

    • 资源ID:459669       资源大小:69.59KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM A820 A820M-2015 Standard Specification for Steel Fibers for Fiber-Reinforced Concrete《纤维增强混凝土用钢纤维的标准规格》.pdf

    1、Designation: A820/A820M 11A820/A820M 15Standard Specification forSteel Fibers for Fiber-Reinforced Concrete1This standard is issued under the fixed designation A820/A820M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of

    2、 last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers minimum requirements for steel fibers intended for use in fiber-reinforced concrete. Five

    3、types ofsteel fibers for this purpose are defined as pieces of smooth or deformed cold-drawn wire; smooth or deformed cut sheet;melt-extracted fibers; mill-cut or modified cold-drawn wire steel fibers that are sufficiently small to be dispersed at random in aconcrete mixture.1.2 This specification p

    4、rovides for measurement of dimensions, tolerances from specified dimensions, and required minimumphysical properties, and prescribes testing procedures to establish conformance to these requirements.1.3 In the case of conflict between a requirement of a product specification and a requirement of thi

    5、s specification, the productspecification shall prevail. In the case of a conflict between a requirement of the product specification or a requirement of thisspecification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase orderrequirements shall n

    6、ot take precedence if they, in any way, violate the requirements of the product specification or thisspecification; for example, by the waiving of a test requirement or by making a test requirement less stringent.1.4 The values stated in either SI units or inch-pound units are to be regarded separat

    7、ely as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.2. Referenced Documents2.1 The following documents, of the issue in eff

    8、ect on the date of material purchase, form a part of this specification to the extentreferenced herein.2.2 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA700 Guide for Packaging, Marking, and Loading Methods for Steel Products for ShipmentC1116/C1116M Spec

    9、ification for Fiber-Reinforced Concrete2.3 ACI Documents:3ACI 506.1 Guide to Fiber-Reinforced ShotcreteACI 544.1R Committee Report on Fiber-Reinforced Concrete2.4 U.S. Federal Standards:4Fed. Std. No. 123 Marking for Shipment (Civil Agencies)2.5 U.S. Military Standards:4MIL-STD-129 Marking for Shipm

    10、ent and Storage3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 deformed fiber, na fiber that is bent, flattened, or roughened to improve mechanical bond to the concrete matrix.3.1.2 modified fiber, na cold-drawn wire fiber whose cross-section has been changed from circular by

    11、shaving the wire.1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01.05on Steel Reinforcement.Current edition approved Oct. 1, 2011Dec. 1, 2015. Published October 2011 January 2015. Origi

    12、nally approved in 1985. Last previous edition approved in 20062011 asA820/A820M 06.A820/A820M 11. DOI: 10.1520/A0820_A0820M-11.10.1520/A0820_A0820M-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Stan

    13、dardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http:/www.concrete.org.4 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700

    14、Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict

    15、 all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International

    16、, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.3 nominal length, nthe length of a deformed fiber, out-to-out, after being deformed.3.1.4 range of equivalent diameter, de-r, na set of limits placed on the equivalent diameter by the specifier. See 8.1.6 and N

    17、ote3.3.2 SymbolsThe following symbols used in this specification are defined as follows:A = cross-sectional area, in.2 mm2d = diameter, in. mmfu = ultimate tensile strength, psi MPal = length, in. mm = l/ d = aspect ratio3.2.1 The subscript n on dimensional units indicates “nominal” and the subscrip

    18、t e indicates “equivalent.” “Nominal” and“equivalent” dimensions are calculated from other measurable dimensions or average weight mass.4. Classification4.1 Five general types of steel fibers are identified in this specification based upon the product or process used as a source ofthe steel fiber ma

    19、terial.4.1.1 Type I, cold-drawn wire.4.1.2 Type II, cut sheet.4.1.3 Type III, melt-extracted.4.1.4 Type IV, mill cut.4.1.5 Type V, modified cold-drawn wire.4.2 Fibers shall be straight or deformed.5. Ordering Information5.1 It shall be the responsibility of the purchaser to specify all requirements

    20、that are necessary for the product under thisspecification. Such requirements to be considered include, but are not limited to, the following:Orders for steel fibers under thisspecification shall contain the following information:5.1.1 ASTM designation and year of issue,5.1.1 Quantity in pounds or t

    21、ons kilograms,5.1.2 Type or types permissible (4.1),5.1.3 Diameter or equivalent diameter (8.1.4), or range of equivalent diameters (8.1.6),5.1.4 Length or nominal length (3.1.3),5.1.5 Deformations, if required, and5.1.6 Whether certification by the manufacturer is required including whether a repor

    22、t is to be furnished (Section 11), and5.1.7 Whether certification by the manufacturer is required including whether a report is to be furnished (Section ASTMdesignation and year of issue 11).NOTE 1For information on satisfactory sizes and aspect ratios, see ACI 544.1R and ACI 506.1, and contact the

    23、manufacturers regarding availability.6. Materials and Manufacture6.1 The materials and manufacturing methods used shall be such that the fibers produced conform to the requirements in thisspecification.7. Mechanical Properties7.1 Tensile Requirements:7.1.1 At least ten individual tensile tests of ra

    24、ndomly selected finished fibers shall be performed for each 5 tons 4 500 kg ofproduct. This is an approximate distribution of one fiber tensile test per every 0.5 ton 450 kg of finished product. The averagetensile strength, fu, of each fiber shall not be less than 50 000 psi 345 MPa. The tensile str

    25、ength of any one of the ten specimensshall not be less than 45 000 psi 310 MPa. Where the parent source material consists of sheet or wire, tensile tests by themanufacturer may be performed on larger samples of source material. One sample of each different source material used shall thenbe tested fo

    26、r each 5 tons 4 500 kg of material. The tensile strength of a single sample of source material shall not be less than50 000 psi 345 MPa.7.1.2 The cross-sectional area used to compute fu shall be carried out to five decimal places, in units of square inches squaremillimetres, and shall be: (1) for dr

    27、awn wire fibers, Type I, the area calculated from the actual diameter of the parent sourcematerial or finished fiber; (2) for cut sheet fibers, Type II, the area calculated from the actual thickness and width of the parentsource material specimen, or if fibers are tested, the area of each individual

    28、 fiber calculated from measured length and weightmass of the fiber. See 8.1.5. (3) for melt-extracted fibers, Type III,or mill-cut fibers, Type IV, specified by equivalent diameter,the area calculated from the equivalent diameter of the fibers. See 8.1.5; and (4) for modified cold drawn wire fibers,

    29、 Type V,specified by a range of equivalent diameters, the area of each individual fiber calculated from the measured length and weightA820/A820M 152mass of the fiber. See 8.1.6. The ultimate tensile load in pounds-force newtons for individual fibers shall be measured to at leastthree significant fig

    30、ures. Testing shall be in accordance with Test Methods and Definitions A370, where applicable.7.2 Bending Requirements:7.2.1 Fibers shall withstand being bent around a 0.125 in. 3.2 mm diameter pin to an angle of 90 at temperatures not less than60F 16C without breaking.NOTE 2The bending requirements

    31、 of this specification provide a general indication of fiber ductility, as may be important in resisting breakage duringhandling and mixing operations. Ductility measures of fiber-reinforced concrete are outside the scope of this specification; see ACI 544.1R.7.2.2 Bend tests shall be conducted on t

    32、en randomly selected specimens of finished fibers. It shall be permissible to performbend tests manually. At least one test consisting of ten specimens shall be made for each 5 tons 4 500 kg of material. At least90 % of the specimens must pass the test.8. Dimensions and Permissible Variations8.1 Dim

    33、ensions:8.1.1 Straight cold-drawn wire (Type I) fibers are specified by diameter (d) or equivalent (de) and length (l), that establish aspecified aspect ratio, (), or (e), as (l / d) or (l / de).8.1.2 Deformed cold-drawn wire (Type I) fibers are specified by the diameter (d) or equivalent diameter (

    34、de) and nominal lengthafter bending (ln). Nominal aspect ratio (n) is established as (ln / d) or (ln / de).8.1.3 Cut sheet (Type II) fibers are specified by thickness (t), width (w), and length (l). Aspect ratio () can be computed as:5l/dewhere:A = tw, andde = equivalent diameter 5=4A/pi .8.1.4 Defo

    35、rmed cut sheet (Type II) fibers are specified by thickness (t), width (w), and nominal length after deformation (ln).Nominal aspect ratio (n) can be computed as follows.5ln/dewhere:A = tw, andde = equivalent diameter 5=4A/pi .8.1.5 Melt-extracted (Type III) and mill-cut (Type IV) fibers are specifie

    36、d by equivalent diameter, (de), and length (l), or nominallength (ln). Equivalent diameter is computed from measured average nominal length and the weight mass of a known quantityof fibers, based upon 0.284 lb/in.3 7 865 kgm3 measured to the nearest 2 10-6 lb 0.1 mg. Nominal aspect ratio, (n), canbe

    37、 computed as follows:n5l/de, or5ln/de8.1.6 Modified cold-drawn wire fibers (Type V) are specified by a range of equivalent diameters, (de-r), and length (l), ornominal length (ln). Equivalent diameter is computed as in 8.1.5. A range of nominal aspect ratios, (n-r) can be computed asfollows:n2r5l/de

    38、2r, or5ln/de2rNOTE 3Specifying a specific diameter or equivalent diameter for Type V fibers is not applicable as the diameters of many Type V fibers vary morethan 610 % in each lot. Therefore a user should provide the limits on diameter or equivalent diameter allowable.8.2 Measurement of Dimensions:

    39、8.2.1 Measurement of dimensions shall be performed on not less than 10 randomly selected specimens for each test to establishthe average for conformance to specified tolerances.At least 90 % of the specimens in each test shall meet the specified tolerancesfor length, diameter or equivalent diameter,

    40、 and aspect ratio.8.2.2 At least one test shall be performed for 5 tons 4 500 kg of finished product.8.3 Permissible Variations:8.3.1 The length, or nominal length shall not vary from its specified value more than 610 %.8.3.2 The diameter, equivalent diameter, or range of equivalent diameters shall

    41、not vary from its specified value more than610 %.8.3.3 The aspect ratio, nominal aspect ratio, or range of aspect ratios shall not vary from its specified value more than 615 %.9. Workmanship, Finish, and Appearance9.1 Surface Condition:A820/A820M 1539.1.1 Seams and surface irregularities shall not

    42、be cause for rejection provided that tensile properties are not less thanrequirements of this specification and mixing performance in concrete is not adversely affected.9.1.2 Rust, mill scale, or other coatings shall not be cause for rejection provided that the individual fibers separate when mixedi

    43、n concrete in accordance with Specification C1116/C1116M, and tensile and bending properties are not less than the requirementsof this specification.10. Inspection10.1 Unless otherwise specified in the purchase order or contract, the manufacturer is responsible for the performance of allinspection a

    44、nd test requirements specified herein. Except as otherwise specified in the purchase order or contract, the manufacturermay use his own or any other suitable facility for the performance of the inspection and test requirements specified herein unlessdisapproved by the purchaser. The purchaser shall

    45、have the right to perform any of the inspections and tests set forth in thisspecification where such inspections are deemed necessary to ensure that material conforms to prescribed requirements.11. Rejection and Rehearing11.1 Rejection:11.1.1 If any test fails to conform to the requirements of this

    46、specification, it shall be cause for rejection of the materialrepresented by the test. Material that is found to be defective subsequent to its acceptance at the manufacturers works may berejected, and the manufacturer notified.11.1.2 Rejection of fibers shall be reported to the manufacturer promptl

    47、y and in writing. Samples representing fibers rejectedby the purchaser shall be preserved until disposition of the claim has been agreed to between the supplier and the purchaser.11.2 RehearingWhen any test fails to meet the requirements of tension, bending, or dimensional tolerances, a retest shall

    48、 beallowed. This retest shall be performed on twice the number of randomly selected specimens originally tested. The results of theretest shall meet the requirements of this specification or the lot shall be rejected.12. Certification12.1 Certificate of ComplianceWhen specified in the purchase order

    49、 or contract, the producer or supplier shall furnish acertificate of compliance stating the product was manufactured, sampled, tested, and inspected in accordance with this specification(including year of issue) and any other requirements designated in the purchase order or contract, and has been found to meet suchrequirements.12.2 Test ReportsWhen specified in the purchase order or contract, test reports shall be furnished to the purchaser containingthe results of all tests required by this specific


    注意事项

    本文(ASTM A820 A820M-2015 Standard Specification for Steel Fibers for Fiber-Reinforced Concrete《纤维增强混凝土用钢纤维的标准规格》.pdf)为本站会员(amazingpat195)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开