欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM A74-2017 Standard Specification for Cast Iron Soil Pipe and Fittings《铸铁污水管和配件的标准规格》.pdf

    • 资源ID:459352       资源大小:957.38KB        全文页数:48页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM A74-2017 Standard Specification for Cast Iron Soil Pipe and Fittings《铸铁污水管和配件的标准规格》.pdf

    1、Designation: A74 16A74 17 Endorsed by theCast Iron Soil Pipe InstituteAmerican Association StateHighway and Transportation Officials StandardAASHTO No.: M 263-77Standard Specification forCast Iron Soil Pipe and Fittings1This standard is issued under the fixed designationA74; the number immediately f

    2、ollowing the designation indicates the year of originaladoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approv

    3、ed for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, andstorm water applications. It establishes standards covering material, manufacture, mechanical and chemi

    4、cal properties, coating, testmethods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast ironsoil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size forsanitary dr

    5、ain, waste, vent, and storm drain systems allows free air space for gravity drainage.1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patternsthat conform with the applicable requirements given in this specification.1.2.1 Pip

    6、e:TablesExtra heavy, 212 ft (0.75 m), 312 ft (1.0 m), 5 ft(1.5 m), 10 ft (3.0 m) lengths1, 2Service, 212 ft (0.75 m), 312 ft (1.0 m), 5 ft (1.5m), 10 ft (3.0 m)1, 2Outside dimensions (for detailing) X1.11.2.2 Fittings:Tables14 bends; long 14 bends 3, 414 bends, long low-hub 514 bends, low heel; high

    7、 heel 6, 714 bends, short sweep; long sweep 814 bends, reducing long sweep 915 bends 1016 bends 1018 bends; long 18 bends 11116 bends 11Y branches 12, 13Y branches, combination 18 bends, single 14Y branches, combination 18 bends, double 14Sanitary T branches, single 15Sanitary T branches, double 15S

    8、anitary T branches, cleanout 16Tapped sanitary T branches, single 17Tapped sanitary T branches, double 17T branches, single and double 18Tapped T branches, single 19Tapped T branches, double 19T branches, cleanout 20-45 offset fitting 21Double hubs 22Long double hubs 22Reducers 23Increasers 24, 25P

    9、traps 26, 271 This specification is under the jurisdiction of ASTM Committee A04 on Iron Castings and is the direct responsibility of Subcommittee A04.12 on Pipes and Tubes.Current edition approved Feb. 1, 2016Oct. 1, 2017. Published February 2016October 2017. Originally approved in 1917. Last previ

    10、ous edition approved in 20132016 asA74 13a.A74 16. DOI: 10.1520/A0074-16.10.1520/A0074-17.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible

    11、 to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West C

    12、onshohocken, PA 19428-2959. United States1TablesDeep seal P traps 28Running traps 29Screw plugs (brass) 30Blind plugs 31Iron-body ferrules 32Side inlets Fig. 3Closet bends 33Tapping bosses 34Reducing 14 bend SV 35Combination Y and 18 bend 36H branch fitting 371.3 The values stated in inch-pound unit

    13、s are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardizationes

    14、tablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A48/A48M Specification for Gray Iron CastingsA644 Terminolog

    15、y Relating to Iron CastingsD1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and CableD3960 Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related CoatingsE8 Test Methods for Tension Testing of Metallic MaterialsE1645 Practice for Preparation

    16、of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead AnalysisE2349 Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Meltingand Pouring; and Cleaning and Finishing2.2 Federal Standard:3Fed. Std. No. 123 Marking for Ship

    17、ment (Civil Agencies)2.3 Military Standard:3MIL-STD-129 Marking for Shipment and Storage2.4 ANSI/ASME Standard:4B1.20 Pipe Threads3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 manufacturer, nthe entity that casts the pipe and fittings covered by this standard.4. Materials an

    18、d Manufacture4.1 The pipe and fittings shall be iron castings suitable for installation and service for sanitary, storm drain, waste, and ventpiping applications. The pipe and fittings shall meet all applicable requirements and tests given in this specification.4.2 The castings shall be made of cast

    19、 iron, produced by an established commercial method that provides control over chemicaland physical properties. Cast iron is a generic term for a series of alloys as defined in Terminology A644 and includes gray ironas well as ductile iron. The castings shall be sound, true to pattern, and of compac

    20、t close grain that permits drilling and cuttingby ordinary methods. The interior surface shall be reasonably smooth and free from defects that would make the castings unfit forthe use for which they are intended.4.3 To minimize the possibility of introducing radioactive material to a melting operati

    21、on, ferrous scrap, pig iron, and anyrecycled ferrous material shall be screened,screened by the manufacturer,manufacturer for radioactivity with detection devicesoperated in accordance with the detection manufacturers instructions. Written operating, calibration, and maintenance proceduresfor the de

    22、tection equipment shall be provided to the purchaser for review when requested. Records shall be maintained by loadof these tests for a period of seven years.4.3.1 Only radiation devices designed specifically for the purpose of screening ferrous material shipments shall be used for thepurpose of con

    23、forming to this requirement. Hand held Handheld radiation detectors (Geiger counters) are not appropriate and shallnot be used for the purpose of conforming to this requirement.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. Fo

    24、r Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4 Available from American Na

    25、tional Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.A74 1724.3.2 Material that is found contaminated with radioactivity shall not be used to produce products covered by this specification.4.3.3 Analysis of castings after the time of production shall n

    26、ot be used to determine compliance to this specification.4.4 Foundries manufacturing products to this specification shall comply to all local, provincial, state, and national safety lawsand regulations and to the requirements of Practice E2349.4.5 Pipe and fittings shall not be patched, filled, or w

    27、elded to correct cosmetic or material defects that occur during the courseof manufacturing.5. Mechanical Properties5.1 Mechanical Tests for Gray IronThe manufacturer shall perform tests to determine mechanical properties of the gray ironused in the manufacture of gray iron soil pipe and fittings. Te

    28、nsion test specimens shall be employed. The manufacturer shallmaintain a record of mechanical tests for a minimum of 7seven years.5.1.1 Tensile Strength TestThe tensile strength shall be not less than 21 000 psi (145 MPa).5.1.2 Tension test reports shall include breaking load of test bars, machined

    29、diameter of test bar, and calculated tensile strength.5.1.3 Analysis of castings or test bars after the time of production shall not be used as evidence of compliance to thisspecification.6. Chemical Test for Gray Iron6.1 The manufacturer shall perform tests to determine the significant chemical con

    30、stituents of the gray iron used in themanufacture of gray iron soil pipe and fittings. Analysis shall be performed at the minimum of once per lot as defined in thisspecification. The manufacturer shall maintain a record of chemical tests performed for a minimum of seven years. The test resultsshall

    31、conform to the following requirements as to chemical composition:Phosphorous (P) 0.38 % MaximumSulfur (S) 0.15 % MaximumChromium (Cr) 0.50 % MaximumTitanium (Ti) 0.10 % MaximumAluminum (Al) 0.50 % MaximumLead (Pb) 0.015 % MaximumCarbon Equivalent 4.10 % Minimum by massNote: Carbon equivalent for gra

    32、y iron = %C+%Si/3+%P/36.1.1 Chemical tests shall be performed at the time of production of the castings covered by this specification.6.1.2 Analysis of castings after the time of production shall not be used as evidence of compliance to this specification.7. Dimensions and Permissible Variations7.1

    33、Pipe:7.1.1 Single-hub pipe shall have a hub at one end and a spigot at the other. Double-hub pipe shall have a hub at each end. Hubsshall have lead grooves. The inner end of hub shall be either with or without a centering recess, all combinations of which shallmake a satisfactory leakproof joint. Hu

    34、b and barrel shall be cast in one piece (see Fig. 1).7.1.2 Single-hub pipe shall be of 212-ft (0.75-m), 312-ft (1.00-m), 5-ft (1.5-m), and 10-ft (3.0-m) nominal laying lengths. Thelaying length shall be as shown in Table 1 and shall be within the tolerances on laying length specified in Table 2. Dou

    35、ble-hubpipe shall be of the same overall length as single-hub pipe of the same size. Its laying length shall be 5 ft minus the two telescopinglengths (dimension Y), or 10 ft minus the telescoping length (dimension Y). Other dimensions shall be as specified in Table 1 asapplicable, and be within the

    36、tolerances specified in Table 2. The dimensions shall apply to pipe before any coating is applied.7.1.3 Pipe shall be straight to the extent that any deflections in the barrel of a 212-ft (0.75-m), 312-ft (1.00-m), and 5-ft (1.5-m)length of pipe shall not exceed 14 in. (6.4 mm) for sizes 4 in. (102

    37、mm) and larger, and shall not exceed 516 in. (7.9 mm) for smallersizes; for 10-ft lengths, deflections in the barrel shall not exceed 12 in. (12.7 mm) for sizes 4 in. and larger, nor exceed 58 in. (15.9mm) for smaller sizes.7.2 Fittings:FIG. 1 Single-Hub and Double-Hub Cast Iron Soil Pipe Laying Len

    38、gthsA74 173TABLE 1 Dimensions of Hubs, Spigots, and Barrels for Extra-Heavy and Service Cast Iron Soil Pipe and Fittings, in.NOTE 11 in. = 25.4 mm; 1 ft = 0.3 m throughout tables.Service Cast Iron Soil Pipe:SizeAAvailabilityBInsideDiameterof HubBOutsideDiameterof BarrelCTelescopingLengthCInsideDiame

    39、terof BarrelCThicknessof BarrelCA J Y B TNom Min2O 2.94 74.68 2.30 58.42 2.50 63.5 1.96 49.78 0.17 4.32 0.14 3.563O 3.94 100.08 3.30 83.82 2.75 69.85 2.96 75.18 0.17 4.32 0.14 3.564O 4.94 125.48 4.30 109.22 3.00 76.2 3.94 100.08 0.18 4.57 0.15 3.815O 5.94 150.88 5.30 134.62 3.00 76.2 4.94 125.48 0.1

    40、8 4.57 0.15 3.816O 6.94 176.28 6.30 160.02 3.00 76.2 5.94 150.88 0.18 4.57 0.15 3.818O 9.25 234.95 8.38 212.85 3.50 88.9 7.94 201.68 0.23 5.84 0.17 4.3210O 11.38 289.05 10.50 266.70 3.50 88.9 9.94 252.48 0.28 6.86 0.22 5.5912O 13.50 342.9 12.50 317.5 4.25 107.95 11.94 303.28 0.28 6.86 0.22 5.5915O 1

    41、6.95 430.53 15.88 403.35 4.25 107.95 15.16 385.06 0.36 9.14 0.30 7.62SizeAThickness of HubWidth of Hub BeadCDistance from LeadGroove to End, Pipeand FittingsBDepth of Lead GrooveHub Body Over BeadS (min) R (min) F (min) P G (min) G (max)2 0.13 3.30 0.34 8.64 0.75 (0.63) 19.05 (16.00) 0.22 5.59 0.10

    42、2.54 0.19 4.833 0.16 4.06 0.37 9.40 0.81 (0.63) 20.57 (16.00) 0.22 5.59 0.10 2.54 0.19 4.834 0.16 4.06 0.37 9.40 0.88 (0.63) 22.35 (16.00) 0.22 5.59 0.10 2.54 0.19 4.835 0.16 4.06 0.37 9.40 0.88 (0.63) 22.35 (16.00) 0.22 5.59 0.10 2.54 0.19 4.836 0.18 4.57 0.37 9.40 0.88 (0.63) 22.35 (16.00) 0.22 5.

    43、59 0.10 2.54 0.19 4.838 0.19 4.83 0.44 11.26 1.19 (1.06) 30.23 (26.92) 0.38 9.65 0.15 3.81 0.22 5.5910 0.27 6.86 0.53 13.46 1.19 (1.06) 30.23 (26.92) 0.38 9.65 0.15 3.81 0.22 5.5912 0.27 6.86 0.53 13.46 1.44 (1.31) 36.58 (33.27) 0.47 11.94 0.15 3.81 0.22 5.5915 0.30 7.62 0.58 14.73 1.44 (1.31) 36.58

    44、 (33.27) 0.47 11.94 0.15 3.81 0.22 5.59Extra-Heavy Cast Iron Soil Pipe and Fittings:SizeA AvailabilityInsideDiameterof HubBOutsideDiameterof BarrelBTelescopingLengthBInsideDiameterof BarrelBThicknessof BarrelBA J Y B TNom Min2* 3.06 77.72 2.38 60.45 2.50 63.5 2.00 50.8 0.19 4.83 0.16 4.063* 4.19 106

    45、.43 3.50 88.9 2.75 69.85 3.00 76.2 0.25 6.35 0.22 5.594* 5.19 131.83 4.50 114.3 3.00 76.2 4.00 101.6 0.25 6.35 0.22 5.595* 6.19 131.83 5.50 139.7 3.00 76.2 5.00 127 0.25 6.35 0.22 5.596* 7.19 182.63 6.50 165.1 3.00 76.2 6.00 152.4 0.25 6.35 0.22 5.598* 9.50 241.30 8.62 218.5 3.50 88.9 8.00 203.2 0.3

    46、1 7.87 0.25 6.3510* 11.62 295.15 10.75 273.05 3.50 88.9 10.00 254 0.37 9.40 0.31 7.87A74 1747.2.1 Dimensions of FittingsAll fittings shall conform to the dimensions specified for hub and spigot ends in Table 1 and Table2, as applicable. Fittings of the patterns specified in this specification shall

    47、conform to the applicable dimensions in Tables 3-37inclusive, and to the tolerances in Table 2. Other patterns (Note 1) shall conform to Table 1, as applicable, for hub and spigotdimensions, and for wall thickness throughout, and to dimension R, Tables 15-17, for the minimum radius of any drainage i

    48、nletsthat such fittings shall be permitted to provide. All fittings shall have spigot ends of sufficient length to provide adequate room formaking joints. All dimensions given in this specification shall apply to fittings before any coating is applied.NOTE 1Such as, for example, fittings known in the trade as “specials,” when designated as being in conformity with this specification.7.2.2 Water Seal and TrapsTraps shall have water seals as follows:Trap Size, in. (mm)MinimumWater seal, in. (mm)2 (50) 2 (50)3 to 6 (75 to 150), incl 212


    注意事项

    本文(ASTM A74-2017 Standard Specification for Cast Iron Soil Pipe and Fittings《铸铁污水管和配件的标准规格》.pdf)为本站会员(inwarn120)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开