欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM A480 A480M-2011a Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate Sheet and Strip《平轧不锈钢和耐热钢厚板材 薄板材和带材的一般要求用标准规格》.pdf

    • 资源ID:458479       资源大小:158.96KB        全文页数:29页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM A480 A480M-2011a Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate Sheet and Strip《平轧不锈钢和耐热钢厚板材 薄板材和带材的一般要求用标准规格》.pdf

    1、;21p;comptd;block;yes;31Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Designation:A480/A480M11 Designation: A480/A480M 11aStandard Specification forGeneral Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet

    2、, and Strip1This standard is issued under the fixed designation A480/A480M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsi

    3、lon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification2covers a group of general requirements that, unless otherwise specified in the purchase order or in anindividual

    4、 specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued byASTM: Specifications A167, A176, A240/A240M, A263, A264, A265, A666, A693, A793, and A895.1.2 In the case of conflict between a requirement of a product specification and a requir

    5、ement of this specification, the productspecification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of thisspecification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase orderrequiremen

    6、ts shall not take precedence if they, in any way, violate the requirements of the product specification or thisspecification; for example, by waiving a test requirement or by making a test requirement less stringent.1.3 The values stated in either inch-pound units or SI units are to be regarded sepa

    7、rately as standard. Within the text, the SI unitsare shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not thebracketed SI values in Annex A2. The values stated in each system are not exact equivalents; therefore, each system must be used

    8、independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unlessthe order specifies the applicable “M” specification d

    9、esignation SI units, the material shall be furnished in inch-pound units.2. Referenced Documents2.1 ASTM Standards:3A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripA176 Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and St

    10、ripA240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vesselsand for General ApplicationsA262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless SteelsA263 Specification for Stainless Chromium Steel-Clad

    11、PlateA264 Specification for Stainless Chromium-Nickel Steel-Clad PlateA265 Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateA342/A342M Test Methods for Permeability of Feebly Magnetic MaterialsA370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA666 Specification

    12、for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat BarA693 Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and StripA700 Practices for Packaging, Marking, and Loading Methods for Steel Products for ShipmentA751 Test Methods

    13、, Practices, and Terminology for Chemical Analysis of Steel ProductsA763 Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless SteelsA793 Specification for Rolled Floor Plate, Stainless SteelA895 Specification for Free-Machining Stainless Steel Plate, Sheet, and StripA

    14、923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels1This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17on Flat-Rolled and Wrou

    15、ght Stainless Steel.Current edition approved Feb. 15,April 1, 2011. Published MarchApril 2011. Originally approved in 1962. Last previous edition approved in 20102011 asA480/A480M10a.A480/A480M 11. DOI: 10.1520/A0480_A0480M-11A.2For ASME Boiler and Pressure Vessel Code applications see related Speci

    16、fication SA 480 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.2This document i

    17、s not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of whatchanges have been made to the previous version. Because it may not be technically possible to adequately depict all changesaccurately, ASTM recommends that users consult prior editions as appropr

    18、iate. In all cases only the current version of the standardas published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United State

    19、s.E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness,Superficial Hardness, Knoop Hardness, and Scleroscope Hardness2.2 AIAG Standard:4B-5 Primary Metals Identification Tag Application Standard2.3 ANSI Standard:5Accredited Standards Com

    20、mittee X 12, (ANSI ASC X12)2.4 Federal Standard:6Fed. Std. No. 123 Marking for Shipment (Civil Agencies)2.5 Military Standards:6MIL-STD-129 Marking for Shipment and StorageMIL-STD-163 Steel Mill Products, Preparation for Shipment and Storage3. Terminology3.1 Definitions:3.1.1 Plate, sheet, strip, an

    21、d cold work as used in this specification apply to the following:3.1.2 platematerial316 in. 5.00 mm and over in thickness and over 10 in. 250 mm in width. Finishes for plate are actuallyshown in Section 13.3.1.3 sheetmaterial under316 in. 5.00 mm in thickness and 24 in. 600 mm and over in width. Fin

    22、ishes for sheet areactually shown in Section 11.3.1.4 stripcold-rolled material under316 in. 5.00 mm in thickness and under 24 in. 600 mm in width. Finishes are detailedin Section 12 for strip, and strip edges in Section 14 for Cold-Rolled Strip.3.1.5 cold workthe changing of mechanical properties b

    23、y work hardening.4. Ordering Information4.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under thisspecification. Such requirements may include, but are not limited to, the following:4.1.1 Quantity (weight and number of pieces),4.1.2 N

    24、ame of material (stainless steel),4.1.3 Condition (hot-rolled, cold-rolled, annealed, heat-treated),4.1.4 Finish (see Section 11 for Sheet, Section 12 for Strip, and Section 13 for Plates). In the case of polished finishes, specifywhether one or both sides are to be polished,4.1.5 Temper (if the app

    25、licable material specification requires this detail),4.1.6 Form (plate, sheet, or strip),4.1.7 Dimensions (thickness, width, length),4.1.7.1 Thickness shall be ordered to decimal or fractional thickness. The use of the gage number is discouraged as being anarchaic term of limited usefulness not havi

    26、ng general agreement on meaning. The gage number shall not be a basis for rejection.4.1.7.2 Thickness, width, and length, when applicable, should be ordered in the same units, for example, 0.060 in. by 48 in. by120 in. 1.52 mm by 1219 mm by 3048 mm.4.1.8 Edge, strip only (see Section 14 for Cold-Rol

    27、led Strip),4.1.9 Type or UNS designation, refer to the applicable material specification,4.1.10 Specification designation and date of issue,4.1.11 Additions to specification or special requirements,4.1.12 Restrictions (if desired) on methods for determining yield strength (see appropriate footnote t

    28、o mechanical propertiestable of the basic material specification),4.1.13 Marking requirements (see Section 25),4.1.14 Preparation for delivery (see Section 25), and4.1.15 Magnetic permeability test (when required). Refer to Section 19.NOTE 1A typical ordering description is as follows: 200 pieces, s

    29、tainless steel sheets, 0.060 in. by 48 in. by 120 in., Type 410 No. 2B finish, ASTMA176-XX.5. Process5.1 The steel shall be manufactured/produced by the following or as specified in the applicable material specification.5.1.1 The steel shall be made by one of the following processes: electric-arc, e

    30、lectric-induction, or other suitable processes.5.1.2 If a specific type of melting is required by the purchaser, it shall be so specified on the purchase order.4Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd., Suite 200, Southfield, MI 48033, http:/www.aiag.org.5Available fr

    31、om American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.6Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.A480/A480M 11a36. Heat Analysi

    32、s6.1 Methods and practices relating to chemical analysis shall be in accordance with Test Methods, Practices, and TerminologyA751.6.2 An analysis of each heat shall be made by the steel producer to determine the percentages of the elements specified in theapplicable material specification. This anal

    33、ysis shall be made from a test sample taken during the pouring of the melt, or from thein-process product later in the manufacturing flow.6.2.1 The heat analysis shall conform to the chemical requirements for each of the specified elements for the grade ordered, aslisted in the applicable product sp

    34、ecification.6.2.2 All commercial metals contain small amounts of elements other than those which are specified. It is neither practical nornecessary to specify limits for unspecified elements, whether intentionally added unspecified elements, residual elements, or traceelements, that can be present.

    35、 The producer is permitted to analyze for unspecified elements and is permitted to report suchanalyses. The presence of an unspecified element and the reporting of an analysis for that element shall not be a basis for rejection,unless the presence of that element causes the loss of a property typica

    36、lly expected for that metal, for the type and quality ordered.6.2.3 The purchaser is permitted to require in the purchase order a maximum limit for an individual element not specified inthe product specification. Such a requirement for an element not listed in the product specification, when acknowl

    37、edged in the orderacceptance, shall be treated as a specified element, with determination of chemical analysis and reporting of that analysis.6.2.4 The purchaser is permitted to make the requirements for any element more stringent, that is, require higher minimums forelements having minimum requirem

    38、ents or ranges with minimum requirements, or requiring lower maximums for elements havingspecified maximums, or ranges with maximums. The purchaser is not permitted to make chemical requirements less stringent.6.2.5 Analysis limits shall be established for specific elements rather than groups of ele

    39、ments, including but not limited to allothers, rare earths, and balance, unless all elements in such a group are similar in technical effect and are associated in typicalmethods of chemical analysis.6.3 The steel shall not contain an unspecified element for the ordered grade to the extent that the s

    40、teel conforms to therequirements of another grade for which that element is a specified element having a required minimum content. For thisrequirement, a grade is defined as an alloy described individually and identified by its own UNS designation in a table of chemicalrequirements within this speci

    41、fication or any specification listed within the scope as being covered by the specification.6.4 The producer is not permitted to certify that material is in compliance with an ASTM product specification when thepurchase order has required that the material contain as a minimum or range an element th

    42、at is neither a specified element nor anintentionally added unspecified element for the ordered grade in accordance with the definitions of Test Methods, Practices, andTerminology A751.7. Product Analysis7.1 The purchaser is permitted to perform a product analysis (formerly check analysis) to verify

    43、 the identity of the finishedmaterial representing each heat or lot. Such analysis shall be made by any of the commonly accepted methods that will positivelyidentify the material.7.2 The chemical composition determined in accordance with 7.1 shall conform to the limits of the material specification

    44、withinthe tolerances of TableA1.1, unless otherwise specified in the applicable material specification or the purchase order. The allowablevariation of a particular element in a single sample for product analysis is permitted to be either above or below the specified range.However, percentages must

    45、exhibit the same tendencies in all samples; that is, the several determinations of any individual elementin a heat shall not vary both above and below the specified range.8. Material Test Report and Certification8.1 A report of the results of all tests required by the product specification shall be

    46、supplied to the purchaser. This material testreport shall reference the product specification designation and year date indicating that the material was manufactured, sampled,tested, and inspected in accordance with requirements of the product specification and has been found to meet those requireme

    47、nts.The material test report shall report the melting process when the purchase order requires either a specific type of melting orrequires that the melting process used is to be reported.8.1.1 The report shall indicate the type of steel. If certifying that the material conforms to the requirements

    48、for more than onetype of steel, the manufacturer may indicate each type of steel on the report, or may issue a separate report for each type of steel.8.2 A signature is not required on the report. However, the document shall clearly identify the organization submitting thereport. Not withstanding th

    49、e absence of a signature, the organization submitting the document is responsible for its content.8.3 A material test report, certificate of inspection, or similar document printed from or used in electronic form from anelectronic data interchange (EDI) transmission shall be regarded as having the same validity as a counterpart printed in thecertifiers facility. The content of the EDI transmitted document must meet the requirements of the invoked ASTM standard(s) andconform to any existing EDI agreement between the purchaser and the supplie


    注意事项

    本文(ASTM A480 A480M-2011a Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate Sheet and Strip《平轧不锈钢和耐热钢厚板材 薄板材和带材的一般要求用标准规格》.pdf)为本站会员(syndromehi216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开