欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM A420 A420M-2010 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service《低温设施用锻造碳钢和合金钢的管道配件用标准规范》.pdf

    • 资源ID:458310       资源大小:107.86KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM A420 A420M-2010 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service《低温设施用锻造碳钢和合金钢的管道配件用标准规范》.pdf

    1、Designation: A420/A420M 10Standard Specification forPiping Fittings of Wrought Carbon Steel and Alloy Steel forLow-Temperature Service1This standard is issued under the fixed designation A420/A420M; the number immediately following the designation indicates the yearof original adoption or, in the ca

    2、se of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers wrought carbon steel andalloy steel fittings of seamless and we

    3、lded construction, cov-ered by the latest revision of ASME B 16.9, ASME B 16.11,MSS SP-79, MSS SP-83, MSS SP-95, and MSS SP-97.Fittings differing from these ASME and MSS standards shallbe furnished in accordance with Supplementary RequirementS58 of SpecificationA960/A960M. These fittings are for use

    4、 inpressure piping and pressure vessel service at low tempera-tures.1.2 Optional supplementary requirements are provided forfittings where a greater degree of examination is desired. Whendesired, one or more of these supplementary requirements shallbe specified in the order.1.3 This specification is

    5、 expressed in both inch-pound unitsand in SI units. However, unless the order specifies theapplicable “M” specification designation (SI units), the mate-rial shall be furnished to inch-pound units.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.

    6、Within the text, theSI units are shown in brackets. The values stated in eachsystem may not be exact equivalents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in non-conformance with thestandard.2. Referenced Documents2.1 In addition

    7、 to those Referenced Documents listed inSpecification A960/A960M, the following list of standardsapply to this specification.2.2 ASTM Standards:3A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA960/A960M Specification for Common Requirements forWrought Steel Piping Fittings2

    8、.3 ASME Standards:B 16.9 Factory-Made Wrought Steel Butt-Welding Fittings4B 16.11 Forged Steel Fittings, Socket-Welding Threaded4Section VIII Division 1, Pressure Vessels4Section IX Welding Qualifications2.4 MSS Standards:MSS SP-25 Standard Marking System for Valves, Fittings,Flanges, and Unions5MSS

    9、 SP-79 Socket Welding Reducer Inserts5MSS SP-83 Steel Pipe Unions, Socket-Welding andThreaded5MSS SP-95 Swage(d) Nipples and Bull Plugs5MSS SP-97 Integrally Reinforced Forged Branch OutletFittingsSocket Welding, Threaded and ButtweldingEnds2.5 ASNT Standards:SNT-TC-1A Recommended Practice for Nondes

    10、tructiveTesting Personnel Qualification and Certification63. Ordering Information3.1 See Specification A960/A960M.4. General Requirements4.1 Product furnished to this specification shall conform tothe requirements of Specification A960/A960M, including anysupplementary requirements that are indicate

    11、d in the purchaseorder. Failure to comply with the general requirements ofSpecification A960/A960M constitutes non-conformance withthis specification. In case of conflict between the requirementsof this specification and Specification A960/A960M, thisspecification shall prevail.1This specification i

    12、s under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.22 on Steel Forgings and Wrought Fittings for Piping Applications and BoltingMaterials for Piping and Special Purpose Applications.Current edition approved M

    13、ay 1, 2010. Published June 2010. Originallyapproved in 1958. Last previous edition approved in 2007 as A420/A420M07.DOI: 10.1520/A0420_A0420M-10.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-420 in Section II of that Code.3For referenced ASTM standards, visit t

    14、he ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Thr

    15、ee Park Ave., New York, NY 10016-5990, http:/www.asme.org.5Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-.6Available fromAmerican Society for Nondestructive Testing (ASNT), P.O. Box28518, 1711 Arli

    16、ngate Ln., Columbus, OH 43228-0518, http:/www.asnt.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Material5.1 The material for fittings shall consist of forgin

    17、gs, bars,plates, seamless or fusion welded tubular products with fillermetal added. It shall conform to the chemical requirements inTable 1, and be made by one of the following processes:open-hearth, basic-oxygen, or electric-furnace. The steels shallbe made using recognized melting practices necess

    18、ary toproduce steels that shall meet the impact requirements of thisspecification.6. Manufacture6.1 Forging or forming operations shall be performed byhammering, pressing, piercing, extruding, upsetting, working,bending, fusion-welding, or machining, or by a combination oftwo or more of these operat

    19、ions. The forming procedure shallbe so applied that it will not produce injurious defects in thefittings.6.2 All welds, including welds in tubular products fromwhich fittings are made, shall be (1) made by welders, weldingoperators and welding procedures qualified under the provi-sions of ASME Secti

    20、on IX,(2) heat treated in accordance withSection 7 of this specification, and (3) nondestructively exam-ined throughout the entire length of each weld in accordancewith Section 14 of this specification. The radiography of weldsshall be done either prior to or after forming at option ofmanufacturer.

    21、Personnel performing NDE examinations shallbe qualified in accordance with SNT-TC-1A.6.3 The welded joints of the fittings shall be finished inaccordance with the requirements of Paragraph UW-35 (a) ofSection VIII, Division 1 of ASME Boiler and Pressure VesselCode.6.4 All butt-weld tees manufactured

    22、 by cold-forming meth-ods shall be liquid penetrant or magnetic particle examined byone of the methods specified in Supplementary RequirementS52 or S53 of Specification A960/A960M. This examinationshall be performed after final heat treatment by NDE personnelqualified under the provisions of SNT-TC-

    23、1A. Only the side-wall areas of the tee need be examined. This area is defined bya circle that covers the area from the weld bevel of the branchoutlet to the centerline of the body or run. Internal and externalsurfaces shall be examined when size permits accessibility.After the removal of any cracks

    24、, the tees shall be re-examinedby the original method. Acceptable tees shall be marked withthe symbol PT or MT, as applicable, to indicate compliance.6.5 Stubends may be produced with the entire lap added bythe welding of a ring, made from plate or bar of the same alloygrade and composition, to the

    25、outside of a straight section ofpipe, provided the weld is double welded, is a full penetrationjoint, satisfies the requirements of 6.2 for qualifications andradiography and 7.1 for post weld heat treatment.7. Heat Treatment7.1 All fittings shall be furnished in the normalized, normal-ized and tempe

    26、red, annealed, or quenched and temperedcondition. All welding shall be completed prior to the austen-itizing heat treatment.7.2 The full thickness of the material from which impact testspecimens are to be obtained shall be heat treated with afurnace charge as specified in 10.4.2 or 10.4.3.7.3 After

    27、forming, the fittings shall be allowed to cool belowthe lower critical before applying one of the heat treatmentslisted in 7.1.7.4 When the fittings are to be post-weld heat treated afterbeing welded by the purchaser and when so specified in theorder, the test specimens shall be subjected to the sam

    28、epost-weld heat treatment. The purchaser shall use the post-weld heat treatment shown in Table 2, unless otherwisespecified in the order.8. Chemical Composition8.1 The steel shall conform to requirements of chemicalcomposition for the respective material prescribed in Table 1.8.2 The steel shall not

    29、 contain any unspecified elements forthe ordered grade to the extent that it then conforms to therequirements of another grade for which that element is aspecified element having a required minimum content.8.3 The chemical composition of weld metal is not requiredto meet the same limits of the base

    30、materials however, thecomposition of the weld deposit shall be such that it meets theminimum mechanical and impact requirements of this specifi-cation. In general, the alloy content shall be similar to that ofthe base metal but shall not exceed 6 % except in the case offittings of 9 % nickel steel.8

    31、.4 A product analysis is optional.9. Tensile Properties9.1 The tensile properties of the fittings material shallconform to the requirements for the applicable grade ofmaterial as listed in Table 3.TABLE 1 Chemical RequirementsNOTE 1All requirements are maximum unless otherwise indicated.NOTE 2Where

    32、an ellipsis (.) appears in this table, there is no requirement.GradeAComposition, %CMnP S Si Ni Cr Mo Cu Cb VWPL6 0.30 0.501.35 0.035 0.040 0.150.40 0.40 0.30 0.12 0.40 0.02B0.08WPL9 0.20 0.401.06 0.030 0.030 . . . 1.602.24 0.751.25WPL3C0.20 0.310.64 0.05 0.05 0.130.37 3.23.8 . . .WPL8D0.13 0.90 0.0

    33、30 0.030 0.130.37 8.49.6 . . .AWhen fittings are of welded construction, the symbols above shall be supplemented by the letter “W”.BBy agreement, the limit for Columbium may be increased up to 0.05 % on heat analysis and 0.06 % on product analysis.CFittings made from plate or forgings may have 0.90

    34、% max manganese.DFittings made from plate may have 0.98 % max manganese.A420/A420M 1029.2 At least one tension test shall be made on each heat ofmaterial and in the same condition of heat treatment as thefinished fittings it represents provided that the wall thickness ofthe fitting and the represent

    35、ative sample thickness do not varymore than14 in. 6 mm. At least one tension test per heat ofweld metal shall be made after heat treatment in the samemanner as the base metal. Results need not be reported unlessSupplementary Requirement S51 of Specification A960/A960M is specified.9.3 Records of the

    36、 tension tests shall be certification that thematerial of the fitting meets the tensile requirements of thisspecification.10. Impact Test Properties10.1 Properties:10.1.1 The notched bar impact properties of the base metaland weld metal shall conform to the requirements of Table 4 orTable 5 for the

    37、applicable grade of material.10.1.2 RetestWhen the average value of the three speci-mens equals or exceeds the minimum value permitted for asingle specimen and the value for more than one specimen isbelow the required average value, or when the value for onespecimen is below the minimum value permit

    38、ted for a singlespecimen, a retest of three additional specimens shall be made.The value for each of these retest specimens shall equal orexceed the required average value. When an erratic result iscaused by a defective specimen, or there is uncertainty in testprocedure, a retest shall be allowed.10

    39、.2 Procedures:10.2.1 All material furnished under this specification shallbe tested for impact resistance at the temperature for therespective grade in Table 6. Exceptions to these requirementsare permissible when agreed upon between the purchaser andproducer and specified in the order, in that the

    40、impact test isacceptable when made at temperatures different from thoseshown in Table 6, provided the test temperature is at least aslow as the intended service temperature, and fittings aresuitably marked in accordance with Section 18 to identify thereported test temperature.10.2.2 The notched-bar

    41、impact test shall be made in accor-dance with the procedure for the simple-beam, Charpy-typetest of Test Methods and Definitions A370. Each impact testshall consist of breaking three specimens.10.3 Specimens:10.3.1 Notched-bar impact specimens shall be simple-beam,Charpy-typeAwith a V-notch in accor

    42、dance with Test Methodsand Definitions A370. Standard specimens 10 by 10 mm incross section shall be used unless the material to be tested is ofinsufficient thickness, in which case the largest obtainablestandard subsize impact specimens shall be used. When thesize or shape of the finished fittings

    43、is insufficient to permitobtaining the smallest standard subsize impact specimens, animpact test by the fitting manufacturer will not be required. Thematerial from which the specimens are taken shall be heattreated with a furnace charge in accordance with 10.4.2 or10.4.3. Impact tests shall be made

    44、from either the raw materialfrom which the fittings are made or from a finished fitting at theoption of the manufacturer.10.3.2 Test specimens shall be obtained so that the longitu-dinal axis of the specimen is parallel to the longitudinal axis ofthe fitting while the axis of the “V” shall be perpen

    45、dicular tothe surface. On wall thickness over 1 in. 25 mm thespecimens shall be obtained with their longitudinal axis located12 in. 13 mm from the outer surface.10.3.3 When testing welds, the notch of the specimen shallbe in the welded joint and, where the diameter and wallthickness permit, the long

    46、itudinal axis of the specimen shall betransverse to the longitudinal axis of the weld. The axis of thenotch shall be perpendicular to the surface.10.4 Number of Tests:10.4.1 A notched-bar impact test, consisting of breakingthree specimens shall be made. Each test shall represent onlysuch fittings fr

    47、om a heat that do not vary from the thickness ofthe material from which the test specimens are taken by morethan14 in. 6 mm.10.4.2 When heat treatment is performed in furnaces notequipped with calibrated recording pyrometers, one impact testshall be made for each heat in each heat-treatment load. Te

    48、stspecimens shall be included with each furnace charge. If thisheat treatment is conducted in continuous-type furnaces notequipped with calibrated recording pyrometers, then one testper heat shall be conducted for each 5000 lb or 2550 kg (orless) of product.10.4.3 When heat treatment is performed in

    49、 furnaces con-trolled within a 50 F 28 C range and equipped withcalibrated recording pyrometers so that records of heat treat-ment are available, then one impact test from each heat isrequired, provided that all other heat treatments are conductedat the same temperatures and within the same 50 F 28 Crange as the furnace charge that contained the test specimens.10.4.4 On fittings of welded construction, additional impacttests of the same number as required in 10.4.1 or 10.4.2 shallbe made to test the weld metal.10.4.5 Specimens showing defects


    注意事项

    本文(ASTM A420 A420M-2010 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service《低温设施用锻造碳钢和合金钢的管道配件用标准规范》.pdf)为本站会员(花仙子)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开