欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASD-STAN PREN 3988-1998 Aerospace Series Test Methods for Metallic Materials Constant Amplitude Strain-Controlled Low Cycle Fatigue Testing (Edition P 1)《航空航天系列 金属材料的试验方法 等幅应变控制的低周.pdf

    • 资源ID:452709       资源大小:1.17MB        全文页数:26页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASD-STAN PREN 3988-1998 Aerospace Series Test Methods for Metallic Materials Constant Amplitude Strain-Controlled Low Cycle Fatigue Testing (Edition P 1)《航空航天系列 金属材料的试验方法 等幅应变控制的低周.pdf

    1、AECMA STANDARD NORME AECMA AECMA NORM prEN 3988 Edition P 1 April 1998 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (+32) 2 775 81 10 - Fax. (+32) 2 775 81 11 ICs: ENGLISH VERSION Aerospace series Test methods for metallic materials Co

    2、nstant amplitude strain-controlled low cycle fatigue testing Srie arospatiale Mthodes dessais applicables aux matriaux mtalliques Essais de fatigue oligocyclique en dformation impose Luft- und Raumfahrt Prfverfahren fr metallische Werkstoffe Niedriglastwechselermdung im dehnungsgesteuerten Versuch T

    3、his “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following com

    4、ment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard C

    5、hecking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Nata - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rouss

    6、eau - 921 38 ICSY-LES-MOULINEAUX CEDEX I Comments should be sent within six months after the date of publication to I Edition approved for publication 1998-04-30 AECMA Gulledelle 94 B-1200 BRUXELLES C5 Chairman Mr Evetts aecma 1998 Contents list Page O Introduction 1 Scope . 2 Normative references 3

    7、 Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Definitions and symbols . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    8、 . . . . . . , . . . . 5 Test equipment 6 Test piece 7 . L O V c O U aJ v) u al c c L v) v) this has to be avoided. B.2.2 Grinding A suitable lubricant shall be used and its flow shall be sufficient to prevent heating of the surface. The abrasive particles shall be continuously removed from the lubr

    9、icant. The diameter of the test piece shall be reduced at a rate of no more than 0,5 pm per turn (plunge grinding) or 0,005 mm per pass (traverse grinding) for the last 0,025 mm. The grinding wheel shall be frequently dressed. The characteristics of the wheel and maximum grinding speed shall be sele

    10、cted as a function of the alloy to be machined: a silicon carbide abrasive is suitable for titanium and aluminium alloys whereas and aluminium oxide abrasive is suitable for steels, nickel or cobalt base alloys. Page 24 prEN 3988: 1998 Annex B (concluded) B.3 Polishing of the test section The final

    11、0,025 mm in diameter shall be removed by longitudinally polishing the test piece. The polishing paper shall be renewed periodically. The force applied to the polishing paper shall be constant and low (2 N to 5 N). An automatic polishing device is recommended. Recommended metal removals and paper gri

    12、t are as follows: - 0,012 mm with P800 paper (particle size: 20 pm to 30 pm); - 0,008 mm with PI O00 paper (particle size: 15 pm to 25 pm); - 0,005 mm with PI 200 paper (particle size: 10 pm to 2 pm). All grinding or turning marks shall be removed with the P800 paper before using a finer grit. Polis

    13、h with each finer grit paper until all marks left by the previous paper are removed, and to impart a maximum surface roughness Ra of 0,2 pm in the test piece axis direction. NOTE: Extreme caution has to be exercised in polishing to ensure that material is being properly removed rather than merely sm

    14、eared to produce a smooth surface. Page 25 prEN 3988: 1998 Annex C (informative) Guidelines on test piece handling and degreasing Unless otherwise specified by the customer or where special surface treatments have been applied, the following guidelines shall be adhered to: C.l Steels Degrease by ful

    15、l submersion in an acetone bath immediately prior to testing. The use of an ultrasonic bath is recommended. Test pieces that are degreased and then not tested for some reason shall be retreated with an anti-corrosion fluid. No special handling requirements are necessary subsequently. Thread lubrican

    16、ts are not necessary at the test temperatures encountered. C.2 Nickel and cobalt base alloys Degrease the test section with acetone and wipe dry with a clean soft cloth. No special handling requirements are necessary subsequently. For tests at temperatures greater than 650 OC, a thread lubricant sha

    17、ll be used sparingly. Any excess evident once the test piece has been inserted shall be removed. C.3 Titanium base alloys Degrease the test section with acetone and wipe dry with a clean soft cloth. Once degreased, the test section shall not be touched other than with clean cotton gloves. In additio

    18、n, everything which touches the test section (extensometer probes, string used to tie on thermocouples, etc.) shall be clean and shall be handled with gloves (to prevent any transfer of salt from the skin to the test piece). Thread lubricants shall not be used. C.4 Aluminium and magnesium base alloy

    19、s Degrease the test section with acetone and wipe dry with a clean soft cloth. No special handling requirements are necessary subsequently. Thread lubricants are not necessary at the test temperatures encountered. _ STD-AECMA PREN -39-ENGL 1998 = LCi123LL CiOlt11523 9TLi 9 Page 26 prEN 3988: 1998 An

    20、nex D (informative) Failure criteria There are various ways of determining a failure criterion, more often associated with an end-of-test criterion than with the total failure of the test piece. It may depend on the interpretation of the fatigue test result and on the nature of the material being te

    21、sted. In fact, any development in the material behaviour shall be taken into account during the test (hardening or softening) and consequently the appropriate end-of-test criterion selected. The failure criteria under consideration are generally based on the appearance, presence or intensification o

    22、f a phenomenon which has been observed or recorded and which indicates severe damage or imminent failure of the test piece. Several criteria may be considered. The conventional number of cycles to failure is defined as the number of cycles corresponding to: 1) Total failure of the test piece: separa

    23、tion into two distinct parts. 2) A certain percentage decrease in the maximum tensile stress in relation to the level determined during the test. 3) A certain percentage decrease in the modulus of elasticity ratios in the tensile and compressive part of the hysteresis loops. 4) A certain percentage

    24、decrease in the maximum tensile stress in relation to the maximum com pressive stress. The use of criterion 2 based on a certain percentage decrease in the maximum tensile stress is recommended. This criterion allows a reduction in the scatter observed in the number of cycles-to- complete-failure of

    25、 the test piece and may be applied to different stress-strain behaviours (hardening, softening, stable behaviour, see fig. 3). In this case, the usual number of cycles to failure Nf is defined as the number of cycles corresponding to a decrease of x % in the stress value extrapolated over the tensil

    26、e stress-versus number of cycles curve when the stress falls sharply. The recommended value of x is 10. This criterion relates to the presence of one (or more) macroscopic crack(s) in the test piece. In general, the fraction of cracked surface in the cross-section of the test piece is of the same magnitude as the fraction of stress decrease.


    注意事项

    本文(ASD-STAN PREN 3988-1998 Aerospace Series Test Methods for Metallic Materials Constant Amplitude Strain-Controlled Low Cycle Fatigue Testing (Edition P 1)《航空航天系列 金属材料的试验方法 等幅应变控制的低周.pdf)为本站会员(syndromehi216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开