1、ASD STANDARD NORME ASD ASD NORM prEN 3660-013 Edition P 1 May 2007 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Avenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERS
2、ION Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 013: Cable outlet, style A, straight, unsealed, with cable tie strain relief Product standard Srie arospatiale Accessoires arrires pour connecteurs circulaires et rectangulaires lectriqu
3、es et optiques Partie 013 : Raccord, type A, droit non tanche, avec tenue du cble par frettage Norme de produit Luft- und Raumfahrt Endgehuse fr elektrische und optische Rund- und Rechtecksteckverbinder Teil 013: Endgehuse, Bauform A, gerade, nicht abgedichtet, mit Arm fr Kabelbinder Produktnorm Thi
4、s “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned D
5、omain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agr
6、eement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a na
7、tional standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 May 2007 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2007 by ASD-STAN prEN 3660-013:20072 Contents Page Foreword2
8、 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Characteristics.3 5 Designation 9 6 Marking 10 7 Technical specification 10 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance wit
9、h the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3660-013:20073 1 Scope This product standard defines a range of cable outlets, style A, for use under the following conditions: Associated electrical connector(s) : EN 3660-
10、002 Temperature range, Class N : 65 C to 200 C Class W : 65 C to 175 C 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced
11、document (including any amendments) applies. EN 2591-*, Aerospace series Elements of electrical and optical connection Test methods. EN 3660-001, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 001: Technical specification. 1)EN 3660-002,
12、 Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 002: Index of product standards. 1)AS85049, Connector Accessories, Electrical General Specification for- 2)3 Terms and definitions For the purposes of this document, the terms and definitio
13、ns given in EN 3660-001 apply. 4 Characteristics 4.1 Dimensions and mass For dimensions and mass, see Figure 1, Figure 2 and Table 1. For spacer pad, see Figure 3. For interface dimensions, see 4.2. All its parts quoted. 1) Published as ASD Prestandard at the date of publication of this standard. 2)
14、 Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001. prEN 3660-013:20074 All dimensions in millimetres Key Key1 Teeth N (see Table 2) 2 Area for cable tie or lacing cord 3 Thread A 4 Marking (see Clause 6) 5 Knurled, manufacturers option 1 Th
15、ree off wire lock holes equi-spaced for 0,8 mm max. diameter wire Figure 1 Figure 2 Figure 3 Spacer pad prEN 3660-013:20075 Table 1 B C aD E Radius F Shell size A Thread Class 2B max. 0,38 max. + 0,2 0 max. Mass max. ClassesN & W Mass max. Spacerpad inches mm mm mm mm mm g g 08 0.4375-28UNEF 16 2,1
16、6,70 4,5 10 0.5625-24UNEF 19 30 2,9 9,95 5,0 12 0.6875-24UNEF 22 31 3,8 12,85 6,5 14 0.8125-20UNEF 25 4,8 16,02 9,0 16 0.9375-20UNEF 29 36 5,7 19,20 10,0 18 1.0625-18UNEF 31 38 21,46 11,0 20 1.1875-18UNEF 35 41 7,1 24,63 13, 5 22 1.3125-18UNEF 38 44 7,8 27,80 15,0 24 1.4375-18UNEF 41 6,29 47 8,8 30,
17、90 18,5 0,65 a“C” dimension is taken when the coupling nut is pulled in forward position. 4.2 Interface dimensions 4.2.1 Associated connector See EN 3660-002. 4.2.2 Standard AS85049 interface See Figure 4, Figure 5 and Table 2. prEN 3660-013:20076 All dimensions in millimetres aAfter max. 5,4 mm fro
18、m the root of the teeth, the cable outlets coupling nut must conform to the G diameter. Figure 4 Figure 5 Table 2 G H I J max. max. min. max. min. max. Shell size mm mm mm mm N Number of teeth 08 15,20 10,26 9,7 10,01 7,59 8,80 12 10 18,40 13,36 12,9 13,16 10,85 12,00 16 12 21,60 16,54 15,8 16,33 13
19、,79 14,94 20 14 24,80 19,51 19,0 19,30 16,92 18,06 24 16 28,00 22,68 22,1 22,48 20,09 21,23 28 18 31,00 25,58 24,9 25,30 22,78 23,93 32 20 34,20 28,88 28,0 28,68 25,96 27,10 36 22 37,40 31,93 31,2 31,65 29,13 30,26 40 24 40,60 35,10 34,4 34,82 32,21 33,34 44 4.3 Material and finish Cable outlet: Mat
20、erial/Finish Class N : Aluminium/Electroless nickel Material/Finish Class W : Aluminium/Olive drab cadmium plate Spacer: Fluorosilicone, colour green prEN 3660-013:20077 4.4 Assembly torque These torque values are intended for installation use only, see Table 3. Table 3 Shell size Torque Nm 0,5 08 1
21、0 12 14 16 18 4,5 20 22 24 9,0 4.5 Coupling thread strength torques These torque values are for test purposes, see EN 2591-420 and Table 4. Table 4 Shell size Torque Nm 0,5 08 10 12 14 16 18 5,5 20 22 24 11,0 4.6 Tests Test details to be in accordance with Table 5 and EN 3660-001. Qualification to b
22、e in accordance with EN 3660-001. prEN 3660-013:20078 Table 5 EN 2591 Test No. Title Not applicable Applicable see EN 3660-001 Particulars 101 Visual examination X 102 Examination of dimensions and mass X See 4.1. 205 Housing (shell) electrical continuity X 212 Surface transfer impedance (from 100 M
23、Hz to 1 GHz) aX 301 Endurance at temperature X 305 Rapid change of temperature X 306 Mould growth X For variant A only 307 Salt mist X Cable outlet not fitted to a connector and suspended with non-metallic cord. Duration: Class N 48 h Class W 500 h 308 Sand and dust X 314 Immersion at low air pressu
24、re X 315 Fluid resistance X For variant A only 316 Ozone resistance X 317 Flammability X For variant A only 318 Fire-resistance X 402 Shock X Method A. Severity 100 g Number of shocks: 4 One in each direction in 2 perpendicular axes 403 Sinusoidal and random vibration X Method B. Figure 3 and Table
25、2. Level J Duration: 8 h at ambient temperature 406 Mechanical endurance X 408 Mating and unmating forces X continued prEN 3660-013:20079 Table 5 (concluded) EN 2591 Test No. Title Not applicable Applicable see EN 3660-001 Particulars Phase A Shell size Load N max. 08 10 12 44,5 14 16 18 89,0 20 22
26、133,5 24 156 420 Mechanical strength of rear accessories X Phase D and Table 4 422 Locking wire hole strength X 513 Magnetic permeability X Not fitted to a connector. Max. value Classes N & W 2,0 a1 GHz to 10 GHz under consideration. 5 Designation EXAMPLE EN3660-013N08A Cable outlet, style A, alumin
27、ium, electroless nickel, shell size 08, with spacer pad. Description block CABLE OUTLET Identity block EN3660-013N08A Number of this standard Material/Finish class, see 4.3 Shell size Variant A with spacer pad NOTE 1 No gaps are required between sections in the part number when printed. NOTE 2 If necessary, the code I9005 shall be placed between the description block and the identity block. prEN 3660-013:200710 6 Marking Refer to EN 3660-001 and Figure 1. 7 Technical specification Refer to EN 3660-001.
