1、, MIL-T-44189C 84 99999Ob O478834 4 E . MIL-T-44 189C 8 May 1991 SUPERSEDING MIL-T-44189B 27 January 1989 MILITARY SPECIFICATION “RWSERS, COLD WEATHER, CAMCUFLAGE 7 E the Department of Defense. This specification is approved for use by all Departments and Agencies of 1. SCOPE 1.1 Scow. This specific
2、ation covers nylon, three layer laminated waterprmf and misture vapor permeable trousers used as a component of the extended cold weather clothing system. 1.2 Classification. The trousers shall be of one typ in the following sizes as specified (see 6.2). Size X-Short Short Reqular Lonq x-small X X X
3、 X small X X X X Medium X X X X X X X X X Large X-Large - - - 2. APPLICABLE rJammms 2.1 Government d0C;uments. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standank, and hanclbooks form a part of this doCsUment to the extent specified herein. Unless otherwise speci
4、fied, the issues of these do;.uments Beneficial comnents (recmndations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: Center, Natick, MA 01760-5019, by using the Standardization D0C;ument Improvement Proposal (DD Form 1426) appearin
5、g at the end of this dmumnt or by letter. U.S. Army Natick Research, Developent, and kgineering AMSC N/A FSC 8415 DISTRIEUI?ION STATEMENP A. Approved for public release; distribution is unlimited. 0 Licensed by Information Handling ServicesMIL-T-44189C are those listed in the issue of the Department
6、 of Defense Index of Specifications and Stan- (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERALI A-A-50083 A-A-50 19 9 V-F-106 V-T-285 DDD-L-20 PPP-B-26 PPP-B-636 MILITARY MIL-T-2283 MIL-T-3530 MIL-F-10884 MIL-F-2 1840 MIL-L-35078 MIL-(2-43701 MIL-(2-44187
7、STANDARDS FEDERAL FED-STD-191 FED-STD-751 MILITARY MIL-STD- 105 MIL-STD-129 MIL-SIP147 MIL-STD-731 Bag, Plastic, Folded Garment Thread, Polyester Core, Cotton- or Fasteners, Slide, Interlocking Thread, Polyester Label: Bag, Plastic (General Purpose) Boxes, Shipping, Fiberboard Polyester-Covered For
8、Clothing, Equipage, and Tentage (General Use) Tape, Textile, Nylon, Woven, White or Dyed Thread and mine: Fasteners, Snap Fastener, Tapes, Hook and Loop, Synthetic Loads, Unit: Preparation of Semiperishable Mildew Resistant or Water Repellent Treated Subsistence Item; Clothing, Personal Equipnent, E
9、quipage; General Specification For Cord, Elastic, Nylon Cloth, Laminated, Waterproof and Moisture Vapor Pemable Textile Test Methods Stitches, Seam, and Stitching Sampling Procedures and Tables for Inspection Marking for Shipent and Storage Palletized Unit Loads Quality of Wood Members for Container
10、s and Pallets by Attributes e f d I (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardi zation Ilocumnts order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2 Licensed by Information Handling Ser
11、vicesMIL-T-44189C 2.2 Non-Government publications. The following documents fom a part of unless otherwise specified, this document to the extent specified herein. the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of do
12、cuments not listed in the DDISS are the issues of the doc=uments cited in the solicitation (see 6.2). Unless otherwise specified, AMERICAN SOCIEXY FOR TESTING AND MATERIALS (ASW) D 3951 - Standard Practice for Comercial Packaging (Application for copies should be addressed to the American Society fo
13、r Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Govemnt standards and other publications are normally available from the organizations that prepare or distribute the d0c;Uments. documents also may be available in or through libraries or other informa- tional services.)
14、this doc=ument and the references cited herein, the text of this document takes precedence. laws anci regulations unless a specific exemption has been obtained. These 2.3 Order of precedence. In the event of a conflict between the text of Nothing in this dmmsnt hawever, supersedes applicable 3.1 Fir
15、st article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide smles. Samples, when furnished, are solely for guidance and Variations frm the specification information to the contractor (see 6.4). my appear in the sale in whi
16、ch case this specification shall govern. 3.3 Materials. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.3.1 Cloth, laminated. The basic material for the trousers shall be cloth, laminated, waterproof and moisture vapor perm
17、eable, conforming to MIL-C-44187. 3.3.2 Seam sealinq tab. The tape for covering and sealing all designated seams and stitching shall be cut in 1 J- 1/16 inch wide strips from Olive- Green 106, laminated cloth fabricated in layers as follaws: a. b. Nylon 6.6 tricot weighing 1.5 _+ 0.3 ounces per squa
18、re yard. The middle layer shall consist of microprous expanded Adhesive, thermoplastic not less than 5.4 mils thick. polytetrafluoroethylene film weighing 0.6 + 0.2 or -0.1 ounces per square yard, c. 3 Licensed by Information Handling ServicesMIL-T-44189C 3.3.2.1 Alternative urethane acrylic seam se
19、alins tape. The alternative seam sealing tap shall be used only when the optional polyolefin microporous laminated basic material is utilized, and shall conform to the follawing characteristics: a. Width, inches: 1 f 1/16. b. Nylon knit backing: Nylon 6.6 tricot fabric weighing 1.35 f 0.2 ounces per
20、 square yard. c. The middle layer shall be a Themset crosslinked urethane acrylic barrier weighing 1.0 ounces per square yard. d. The outer layer shall consist of a law temperature polyurethane adhesive with 240% (nominal) melt point not less than 7.5 mils thick (see 6.6 for recormiendeed settings).
21、 Under no circumstances shall the tape machine utilized incorporate an heat output in excess of nozzle air pressure control, or a nozzle 3.3.3 Tape, nylon. The tape for suspender loops shall be 1/2 inch flat nylon tape, black or Olive Drab 7, conforming to MIL-T-2283. 3.3.4 Drawcord, elastic. The tr
22、ouser drawcord shall be 3/16 inch diamter nylon elastic conforming to type II of MIL-C-43701. seared and knotted. All ends shall be heat 3.3.5 Fastener, tape, hook and loop. The fastener tape shall be nylon Olive Green 106 conforming to type II, class 1 of MIL-F-21840 and in the widths specified in
23、table II. 3.3.6 Fastener, slide. All slide fasteners shall be in lengths specified pr size, color black, type I, style 3, size MS, nylon or polyester contin- uous coil or ladder configuration, conforming to V-F-106 and shall be equipped with a thong. 3.3.7 Barrel lock. The barrel locks for the ends
24、of the drawcors shall be black, IIW Nexus Barreloc or equivalent. 3.3.8 Fastener, snap. The stud and post parts of the snap fastener shall be style 2A, finish 2 male and female caplete, consisting of stud and eyelet size 1 or 2 with button size 1 or 2 and socket conforming to MIL-F-10884, except an
25、uncapped button may be used in areas where the surface will be concealed by a layer of base cloth. 3.3.9 Thread. The thread for all seaming and stitching shall be polyester, size B, 2 or 3 ply, shade S-1, C.A. 66022 conforming to type I, class 1, subclass B, of V-T-285. As an alternate, polyester co
26、re, size 40, 2 or 3 ply, shade S-1, conforming to A-A-50199 may be used. All thread shall be water repellent treated in accordance with MIL-T-3530. 4 Licensed by Information Handling ServicesMIL-T-44189C 84 W 9999906 0478818 1 W MIL-T-44189C 3.3.10 Labels. Each of the trousers shall have a class 1 i
27、dentification label, class 2 size label, and a class 3 instruction label conforming to type VI of DDD-L-20. The label color shall be Medium Green, C.A. 70034, 70130, or 70131. The labels shall Shaw fastness to laundering. 3.3.10.1 Size label. The size label shall be as follaws: 5 1 Licensed by Infor
28、mation Handling ServicesMIL-T-44189C crl 4 i .a cn e cs! 6 A Licensed by Information Handling ServicesMIL-T-44189C 3.3.10.2 Identification-instruction label. The combination identifica- tion-instruction label shall be as follows: a. Fixed Laundr: The trousers should be laundered utilizing “Formula K
29、“ of FM 10-17. NOIE: Do NI STARCH, BLEACH, OR DRY CLEAN. b. Field Laundry : The trousers should be laundered utilizing “Formula VIII“ of IM 10-280. NOIE: Do NI STARCH, BLEACH, OR DRY Q;EAN. .r Drvinq: The trousers should be finished in a tumble-dryer, loaded not mre than 2/3 of rated capacity at law
30、 heat cycle (do not exceed 100%). Remove imnediately from dryer. Avoid over-drying. NE: Do NI PRESS. c. Machine/Hand Launderinq. Use wash/wear/pement press fabric cycle or wash by hand, using warm water (90 to 110%) and mild pawdered laundry detergent. Rinse thoroughly in clean wann water. NOIE: Do
31、NOT USE CJ3XRINE OR STARCH. Dryinq: -le dry at law temperature (100%) and remove imnediately from dryer. Avoid over-drying. and place on rust-proof hanger. Wl?E: Do NI PRESS. 3.3.10.3 Combination size, identification, and instruction label. The identification label, size label, and instruction label
32、 may be combined into one label, conforming to class 14. The three labels shall be printed as one continuous label with the size label first and the identification and instruction labels placed belaw the size label. The size and identification labels may be combined and the contents placed above the
33、 instruction label. A space of 1/2 inch minimum shall be maintained between the 1-1s. addition, a solid line 1/16 inch minimum width shall extend across the entire label, approximately in the middle of the 1/2 inch blank space. requirement shall conform to the class 3 label. To drip dry, remove from
34、 water e In The coating 3.3.11 Cvelet metallic. The eyelet for the trouser gram-on waistband shall be Stimpson telescoping eyelet with neck washer, part nimibers A1215 and A665 or equal (see 6.5). 3.4 Desicm. The trousers shall be camouflage tu the outside with an elastic drawcord at the waist, slid
35、e fastener fly opening and ankle openings with fastener tape adjustment tabs. 3.5 Patterns. Stan- patterns which provide an allawance of 1/4 inch for all seams will be furnished by the Government. shall not be altered in any way and are to be used only as a guide for cutting the contractors working
36、patterns. identical to the Government patterns. The Government patterns The working patterns shall be 7 Licensed by Information Handling ServicesMIL-T-44389C 84 M 999990b 0478823 3 M MIL-T-44 189C 3.5.1 Pattern part s. The component parts shall be cut from the material specified and according to the
37、 number of parts listed in table I. TABLE I. List of pattern part S Material Nomenclature Parts Cloth, laminated Front and back Seat patch Knee patch Leg insert Pocket flap Ankle tab Pocket facing 3.6 Construction. The construction shall conform in all respects to the requirements specified in table
38、 II and herein. for guidance and information. appear in figure 1, this specification shall govern. Figure 1 is furnished solely Should variation from this specification 3.6.1 Stitches, seams, and stitchinq. Ail stitches, seams and stitching shall conform to FED-STD-751. The type of seam, stitching a
39、nd stitches per inch shall be as specified in table II. with seams sewn so that no raw edges, run-Offs, pleats, puckers or open seams occur. When two or more methods of seams or stitches are given for the same operation, any one may be used. Seam allawances shall be maintained 3.6.1.1 Tvpe 301 stitc
40、hing. Ends of all stitching shall be backstitched Ends of a continuous line of stitching Thread tensions shall be maintained or overstitched not less than 1/2 inch except where ends are turned under or caught in other seams or stitching. shall over-lap not less than 1/2 inch. so that there will be n
41、o loose stitching resulting in loose bobbin or top thread or excessively tight: stitching resulting in puckering of the materials sewn. The lock shall be embedded in the materials sewn. 3.6.1.1.1 Repairs of type 301 stitchinq. a. When thread breaks, skipped stitches, run-Offs, or bobbin mouts occur
42、during sewing, the stitching shall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. i/ b. Except for prestitching, thread breaks or two or more consecutive The stitching shall start a minimum of 1/2 inch skipped or run-off stitches noted during inspecti
43、on of the item shall be repaired by overstitching. in back of the defective area, continue over the defective area, and continue 8 5 . O O Licensed by Information Handling ServicesMIL-T-44189C 84 9 999990b 0478822 3 E I MIL-T-44189C a minimum of 1/2 inch beyond the defective area onto the existing s
44、titching, Loose or excessively tight stitching shall be repaired by rmving the defective stitching without damaging the materials, and restitching in the required manner. I/ - i/ When making the above repairs, the ends of the stitching are not required to be backstitched. 3.6.1.2 Tvpe s 504, 515, an
45、d 516 stitchinq. Thread tension shall be min- tained so that there will be no loose stitching. accordance with 3.6.1.1.la and b. there will be no loose or excessively tight stitching resulting in puckering of the materials sewn. Ail repairs shall be in Thread tension shall be maintained so that 3.6.
46、1.3 Bartacks. Unless otherwise specified, all bartacks shall be 3/8 f 1/16 inch long and 1/8 f 1/32 inch wide, .and shall contain 28 stitches. Bartacking shall be free fromthread breaks and loose stitching. 3.6.1.4 Automatic stitchinq. Automatic machines may be used to perfom any of the required sti
47、tch patterns provided the requirements for the stitch pattern, stitches per inch, and size and type of thread are met; and at least three tying, overlapping or back stitches are used to secure the ends of the stitching. 3.6.1.5 Thread ends, All thread ends shall be triml 8 Q c, E III. Finished measu
48、rements (inches1 1/2 Waist i/ Inseam 2/ outseam 3/ x-small small Medium Short x-small small Medium Large x-Large Resular x-small small Mediun X-Urge Large x-small small Medium mge X-Large Tolerance Plus Minus 15 17 19 15 17 19 21 15 17 19 21 23 15 17 19 21 23 1/2 1/2 26-1/8 26-1/4 26-3/8 28 28-1/8 2
49、8-1/4 28-3/8 30 30-1/8 30-1/4 30-3/8 30-1/2 32 32-1/8 32-1/4 32-3/8 32-1/2 3/4 3/4 35 35-1/2 36 37-1/2 38 38-1/2 39 40 40-1/2 41 41-1/2 42 42-1/2 43 43-1/2 44 44-1/2 1/2 1/2 i./ With trousers fastened measure along center of waistband from folded edge to folded edge. - 2/ Measure inseam of trousers from crotch seam to bottom edge of trouser leg hem. 21 Licensed by Information Handling ServicesMIL-T-44189C - 3/ Fasten slide fastener and ankle tab at leg insert. Snap pocket welt. With trousers flat, masure fromtop of waistband above front edge of welt to trouser leg hem be
