1、flIL-S-50200B (41 9999906 1864765 09T MIL-S-50200B (AR) AMENDMENT 4 18 August 1993 C UPERC ED ING AMENDMENT 3 O9 August 1983 MILITARY SPECIFICATION SAFETY AND ARMING DEVICE, GUIDED MISSILE: Ml00 PARTS, ASSEMBLING, LOADING AND PACKING FOR (U) This Amendment forms a part of Military Specification MIL-
2、S-50200B (AR), dated 24 February 1976, and is approved for use by the US Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Departments of Defense. (U) PAGE 3 3.5, Line 1, after - Add: “9235260.“ (U) 3.5, Line 4: Delete “-20 degrees FI and s
3、ubstitute “-25 degrees F“. (U) PAGE 4 3 .6.1, column “TO PIN NUMBER (ALL SHORTED TOGETHER) I, line i: Add an asterisk above f12.3.4“ - should be li2*, 3*, 4*, l.“. Line 2: Add as asterisk above “3.4“ - should be “3*, 4*, 1, 2 .If. (U) PAGE 5 3.8.1: Delete in its entirety and substitute the following
4、: (U) “3.8.1 (U) Dynamic Safety Status Switch Circuit Monitor in Safe Position. The safety status circuit resistance, pins 1 and 2 of the 9 pin connector, shall be not greater than 0.3 ohms and shall not change by more than 0.05 ohms when an electrical insulator no greater than 0.005 inches thick is
5、 placed between the applicable switch blade and each one of the eight contact wipers, one at a time while moving the detonator block.assembly in accordance with the procedure specified in paragraph 4.5.6.1. * 3.8.2, (AS1) and (AS2) under requirements: Delete “500.0 megohms“ and substitute “20. O meg
6、ohms“. (U) PAGE 6 3.8.3.1, line 9:. Delete 10“ and substitute 25“. . (U) ASC h/A 1 of 7 FSC 1336 DISTRI3UTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-50200B (4) 799770
7、6 1864766 T26 MIL-S-50200B (AR) AMENDMENT 4 3.8.3.4: Delete in its entirety and substitute the following: (U) “3.8.3.4 (U) Slow Power Loss (SP). Each self-destruct circuit shall deliver a firing pulse when an input voltage of 40 + .2 - .O volts in series with 7.13 5 1 degrees K ohms is applied to th
8、e S 6 NOILV70SI 16.E XV37 dllOX3 ZZIS 31ms 444 4-44 x3;r I 444 wuw www uuw uuw II 4W Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-50200B (4) = 9999906 l1864770 457 m MIL-S-50200B (AR) AMENDMENT 4 a, 4 a U .rl 4 a a a e 516 NOIL3Nnd AXWIXd VZ
9、UZZZZZ uuzzzZvz 56E NOILVIOSI 44444444 U O 2 I 7; U c aJ .li P E 4 I 4 al N .rl ul U O I4 O m m I m N b O Frr 4 41 m w H B n Fr m N I U 4 O V I V W a) N .rl cn U O 4 b O w a, N -rl cn aJ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-50200B (4
10、) 9999906 1864771 393 MIL-S-50200B (AR) AMENDMENT 4 SCHEMATIC: resistor from base of Ql to S2 (SAFE) “R15“ should be “R10“. (U) NOTE: The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the prev
11、ious amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccurancies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. (U) Custodian: Army-AR Preparing activity: Army-AR (Project 1336-A636) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
