1、MIL-S-4392bJ 84 W 999990b 0493711 3 W MIL-S-43926J 30 Auqust 1991 SUPERSEDING MIL-S-43926H 25 March 1988 MILITARY SPECIFICATION SUIT, CHEMICAT, PRCYJTCPIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This specification cove
2、rs a disposable suit for wear as an The suit consists of separate coat and trousers and is made with a overgarment to protect against chemical warfare agents or periods of 1 to 22 days. cottonhylon shell and a sewn in laminated foam lining impregnated with activated charcoal. Equipnent (LCC distribu
3、tion is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43926J 2. APPLICABLE lXxmmm3 2.1 Gaveniment documents. 2.1.1 Specifications, standards and hanbcmks. The following specifica- tions, standards and handbooks form a part of this
4、document to the extent specified herein. are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Unless otherwise specified, the issues of these documents SPECIFICATIONS FEDERAT, A-A-208 A-
5、A-5 O 19 8 A-A-50 199 V-F-106 DDD-L-20 PPP-B-6 3 6 PPP-F- 32 O MILITARY MIL-B- 117 MIL-B- 3 7 1 MIL-B-543 MIL-D-3464 MIL-T-3530 MIL-F-10884 MIL-C-12189 MIL-G-16491 MIL-F-21840 MIL-L-35078 MIL-C-43303 MIL-T-43566 MIL-(2-43858 Ink, Marking, Stencil, paque (Porous and Non- Thread, Gimp, Cotton Buttonho
6、le Thread, Polyester Core, Cotton- or Polyester- Fasteners, Slide, Interlocking Label: Boxes, Shipping, Fiberboard Fiberboard: Corrugated and Solid, Sheet Stock Porous Surfaces) Covered For Clothing, Equipage, and Tentage, (General Use) (Container Grade) and Cut Shapes Bags, Sleeves and Tubing Braid
7、, Textile, Tubular Buckles, Tongueless and Web Strap Desiccants, Activated, Bagged, Packaging Use and Thread and mine, Mildew Resistant or Water Fasteners, Snap Cloth, Coated: Gromnet, Metallic, General Specification for Fastener Tapes, Hook and imp, Synthetic Loads, Unit: Preparation of Semiperisha
8、ble Static Dehumidification Repellent Treated Butyl Coated, Toxicological Agents Protective Subsistence Items; Clothing, Personal Equiprent and Equipage; General Specification For Cord, Elastic, Cotton Tape, Textile, Cotton or Polyester, General Cloth, Laminated, Nylon Tricot Knit, Polyurethane Purp
9、ose, Natural or in Colors Foam Laminate, Chemical Protective and Flame Resistant 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-4392bJ 84 = 7999906 0493733 7 MIL-S-43926J MIL-C-44031 - Cloth, Camouflage Pattern: Woodland, Cotton and MIL-C-44
10、034 - Cloth, Twill, Camouflage Pattern, Cotton and Nylon MIL-P-44406 - Pouches, Plastic Film Nylon For Desert Uniform STANDARDS FED-STD-101 - Test Procedures for Packaging Materials FED-STD-595 - Colors Used in Government Procwmnt FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 -
11、Sampling Procedures and Tables for Inspection by Attributes MIL-SITI-129 - Marking for Shipnt and Storage MIL-STD-147 - Palletized Unit Lmds MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and military specifications, standards and hand
12、books are available from the Standardization D0C;uments Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. the issues of the docsuments which are DoD adopted
13、are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, Unless otherwise specified, AMERICAN SOCIEXY FOR TESTING AND MATERIALS (ASIM) F 88
14、- Test Method for Seal Strength of Flexible Barrier Materials (Application for copies should be addressed to the American Society for (Non-Governmnt standards and other publications are normally available Testing and Materials, 1916 Race Street, Philadelphia, PA from organizations that prepare or di
15、stribute the documents. also may be available in or through libraries or other infomiational services. ) this document and the references cited herein, the text of this document takes precedence. laws and regulations unless a specific exemption has been obtained. 19103-1187.) These docsuments 2.3 Or
16、der of ?xecedence. In the event of a conflict between the text of Nothing in this document, however, supersedes applicable 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-4392bJ 4 = 999990b 0493734 9 MIL-S-43926J 3. REQUIREMENTS 3.1 First art
17、icle. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide samples. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variations from this specifica- tion my appear in the sampl
18、e, in which case this specification shall govern. 3.3 Materials. It is encouraged that recycled mterial be used when practical as long as it meets the requirements of this specification. 3.3.1 Outer shell. The camouflage printed and guarpel treated cotton and nylon twill cloths used for the outer sh
19、ell for the classes 1 and 3 suits shall conform to the requirements specified in 3.3.1.1 and 3.3.1.2. 3.3.1.1 Class 1 suit. The cloth shall be woodland camouflage printed and shall confonn to class 2 of MIL-C-44031, except that the colorfastness to laundering (after three cycles) shall rate at least
20、 “fair“. 3.3.1.2 Class 3 suit. The cloth shall be desert camouflage printed (3 color) and shall conform to class 3A of MIL-C-44034. 3.3.2 Lining. The laminated cloth used for the lining shall conform to type III of MIL-C-43858 (see 6.5). 3.3.3 Butyl cloth. coat and trouser pockets and as reinforceme
21、nt for elbaws and knees shall conform to MIL-C-12189. The heavily coated side of the butyl cloth, when used, shall face to the outside of the coat or trousers. The color shall approximate Olive Drab 177. shall not apply. In addition, the adherability test for lb/inch width, initial, after water inme
22、rsion, and after heat aging requirements of MIL-C-12189 shall not apply. meet the requirements specified in MIL-C-12189 when tested in accordance with 4.4.1.1. The butyl cloth used for protective pieces beneath all The colorfastness and dry crocking requirements Initial toxicological agents resistan
23、ce shall 3.3.4 Elastic cord. The cotton elastic cord for the drawcord at bottom of coat shall be 3/16 inch in diameter, conforming to class 2 of MIL-C-43303. The color shall be Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Tan 380 for class 3 suit, and the
24、 colorfastness requirements shall not apply. 3.3.4.1 Elastic cord resin impreqnatinq aqent. The resin agent used for dipping or impregnating the ends of the drawcords shall be cellulose acetate or cellulose acetate butyrate to prevent ravelling. impregnated ends shall be at least 1/2 inch in length.
25、 The dipped or 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-4392bJ 84 9999906 0493735 O 9 MIL-S-43926J 3.3.5 Slide fasteners. The slide fasteners shall be continuous element nylon or polyester (spiral type), size MS and in the types and st
26、yles indicated. before being sewn into the gmnt. After insertion into the gmnt, the pin must be able to be fully inserted through slider, seated into box and operable. shall be a staple type and shall be positioned and sewn, enclosing the sides and ends of the fastener chain. abut the end of the sli
27、de fastener chain, and be securely affixed to the slide fastener tape without damage to the tape or chain. pulls shall have a hole with sufficient size to accomnodate a 3/8 inch wide thong when a short tab pull is used on the coat front, the tab shall have a minimum length of 7/8 inch. The slide fas
28、teners shall conform to the requirements of V-F-106 The salt spray test shall not apply. The closed-end bottom stop Solid type closed-end bottom stops shall The slide fastener Coat - Type IV, style 8, long or short tab pull Trouser fly and leg openings - Type I, style 3 or style 4 (cam only) short t
29、ab pull 3.3.5.1 Slide fastener tape. The color of the slide fastener tape shall be Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Khaki Shade P, Cable Nunher 66516 for class 3 suit, and the colorfastness requirements shall not apply. tape shall be 9/16 or 5
30、/8 inch. The width of the slide fastener 3.3.6 Braid. 3.3.6.1 Leq drawcord. The solid tubular cotton braid for drawcords, at leg bottans shall conform to type IV, class 2, 4/32 inch diameter of MIL-B-371. 34094 of FED-STD-595, for class 1 suit, and Tan 380 for class 3 suit, and the colorfastness req
31、uirements shall not apply. The color shall be Camouflage Green 483 approximating Color Chip 3.3.6.1.1 Drawcord braid resin imprmatinq aqent. The resin agent used for dipping or impregnating the ends of the drawcords shall be cellulose acetate or cellulose acetate butyrate to prevent ravelling. impre
32、gnated end shall be at least 1/2 inch in length. forming to type VI1 of MIL-B-371, or outer shell material (see 3.3.1) may be used for these ccmpnents. The color shall be Camouflage Green 483 approxi- mating Color Chip 34094 of FED-STD-595, for the class 1 suit, and Tan 380 for class 3 suit, and the
33、 colorfastness requirements shall not apply. and fabrication details when outer shell material is used shall be as specified in table I. The dipped or 3.3.6.2 Suspender loops and slide fastener pull thonqs. Either braid con- Cutting 3.3.7 Hook and loop fastener tape. The hook and loop fastener tape
34、for securing coat chest pockets, and coat center front overlap shall be 5/8 inch wide hook and loop tape, and for sleeve cuff adjustments, coat pocket flaps, trouser hip pocket flaps and hip pockets shall be 1 inch wide hook and loop 5 . Provided by IHSNot for ResaleNo reproduction or networking per
35、mitted without license from IHS-,-,-MIL-S-43926J 4 9999906 0493716 2 = MIL-S-43926J tape conforming to type II, class 1 of MIL-F-21840. The color shall be Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Tan 380 for class 3 suit, and the colorfastness require
36、ments shall not apply. 3.3.8 Tape. 3.3.8.1 Adjustment strap tapes. The adjustment strap tape shall be type I, class 3, 5/8 inch width, Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Tan 380 for class 3 suit, conforming to MIL-T-43566, except that the colorf
37、astness requirement shall not apply. 3.3.8.2 Chest pocket pull tapes. The chest pocket pull tapes, when not cut from ends, shall conform to type I, class 3, 3/8 inch width, Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Tan 380 for class 3 suit, conforming
38、to MIL-T-43566, except that the colorfastness and curvature requirements shall not apply. 3.3.9 Snap fasteners. Snap fastener assemblies conforming to MIL-F-10884 shall be used to secure front closure of trousers, to attach the coat back to the trouser back, and to secure trouser cargo pocket flaps.
39、 The fasteners to secure trouser closure and trouser cargo pocket flaps shall conform to style 2 or 2A, finish 2. Style 2 shall consist of a 24 line button, size 1 or 2 socket for the female half; and eyelet size 1 or 2, with stud for the male half. female half; and eyelet, size 1 or 2, with stud fo
40、r the male half. The follawing exception to MIL-F-10884 shall apply: A double stud or as an alternate, style 2 or 2A stud-eyelet combination shall be used on the right side of trousers at waist opening. The snap fasteners for attaching the back of the coat to the trousers shall conform to style 2, f
41、inish 2, 24 line size button. contractor so as to insure a secure clinch of components to material. Style 2A shall consist of a button, size 1 or 2 and socket for the The barrel length of button and eyelet shall be selected by the 3.3.9.1 Grorrniet. The grmts (when applicable) for the coat bottom an
42、d trouser leg drawcords shall conform to type II, class 3, size O of MIL-G-16491. 3.3.10 Buckles. The buckles for hip adjustment straps shall be tongue- less, 2 bar, conforming to type II, class 3, style 3, 5/8 inch of MIL-B-543. 3.3.11 Gim. The cotton gimp for reinforcing buttonholes shall conform
43、to type I or II, ticket number 8 of A-A-50198 and the color shall be Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Khaki P-1, Cable No. 66019 for class 3 suit, and the colorfastness requirements shall not apply. 6 Provided by IHSNot for ResaleNo reproducti
44、on or networking permitted without license from IHS-,-,-MIL-S-4392bJ 84 9999906 OY937L7 4 MIL-S-43926J 3.3.12 Thread, cotton- or polvester-covered, polvester core. The cotton-covered or polyester-covered, polyester core threads for seaming and stitching the coat and trousers shall be ticket numbers
45、50 and 70, 2 ply conforming to A-A-50199. 3.3.12.1 Color. The threads shall be Camouflage Green 483 approximating Color Chip 34094 of FED-STD-595, for class 1 suit, and Khaki P-1, Cable No. 66019 for class 3 suit, and the colorfastness requirements shall not apply. The thread used to sew the laminat
46、e cloth for the lining my be white where not exposed to outside. 3.3.12.2 Water repellent treatment. The cotton-covered or plyester- covered polyester core threads shall be water repellent treated conforming to type II, class 3 of MIL-T-3530. Lubrication of the quarpel treated thread by any means pr
47、ior to or during the sewing is prohibited. 3.3.13 Labels. All clothing labels shall be in accordance with DDD-L-20. Each of the coats and trousers shall have an identification, a size, and an instruction label. These three labels may be combined. The colorfastness requirements shall not apply. 3.3.1
48、3.1 Identification label. The identification label shall confom to type VI, class 1 of DDD-L-20, except that the surveillance marking require- ments in MIL-C-43858 for the laminated cloth shall appear under the last line of inscription on the label. The surveillance marking my be hand printed or sta
49、mped. points affixed with Black (No. 37038) ink conforming to type I of A-A-208. Size of characters for the lot number shall be a minimum of 10 3.3.13.2 Size label. The size label shall conform to type VI, class 2 of DDD-L-20. 3.3.13.3 Instruction label. The instruction label shall conform to type VI, class 3 of DDD-L-20 and shall include the following instructive inform- tion for each respective size. Instructive infomiation shall be printed in letters not less
