1、MIL-S-q3292D Lb 7799906 0395932 W c-/s- y/ 3-45-/3 CH-PO UN MIL -S-43292D 23 Auwst i989 SUPERSEDING MIL -S-43292C 10 November 1981 - MIL ITA RY SPECIFICATION - . ._ STATIC LINES, CARGO PARACHUTES, GENERAL SPECIFICATION FOR -. This specification is approved for use by all Departments and Agencies of
2、the Department of Defense. 1 1 Scope. This specification covers the general requirements for four .types of airdropcargo static lines. 1.2 Classification. The static lines shall be of the following types, as specified (see 6.2): Type 1. - G-14 Cargo Parachute Type IT - G-12 Cargo Parachute Type III
3、- Load Transfer, Cargo Platform, Break-Away.Type Type IV - Ringslot Cargo Parachutes Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Cente
4、r, Natick, MA Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. 01760-5014 by using the self-addressed Standardization AMSC N/A FSC 1670 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS /3 PAGESI P
5、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Li3272D Lb 79977b 0175433 T M MIL-Sd3292D 2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks
6、form a part of this document to the extent specified herein, those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2) e Unless otherwise specified, the issues of these documents are SPECIFICATION
7、S FE DE RAL PPP-B-26 - Bag, Plastic, (General Purpose) PPP-B-6l - Boxes, Wood, Cleated-Plywood PPP-B-636 - Boxes, Shipping, Fiberboard T-T-871 - Twine, Cotton, Wrapping STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspectio
8、n by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS) , 5801 Tabor Avenue, Phila
9、delphia, PA 19120-5099 . 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein, are those cited in the solicitation. Unless otherwise specified, the issues 2 Provi
10、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43272D Lb H 7377906 037573Li L MIL 3-4 3292D DRA WINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 11-1-134 - Static Line, Load Transfer, Cargo Platform, 11-1-219 - Static Line; Carg
11、o Parachute Break-Away Type; Assembly Complete AIR FORGE 59 56 1 71 - Static Line - Pilot Chute, G-12 Parachute (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-EMSS, Natick, MA 01760-5024.) 2.2 Non-Government publications. The fo
12、llowing document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DO
13、DISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphi
14、a, PA 19103-1187.) (Mon-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a confl
15、ict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6-21,
16、 a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Materials. Materials and hardware requirements shall be in accordance with this document and with subsidiary documents cited on the applicable drawings. It is encouraged that recycled material be used when
17、 practical as long as it meets the requirements of this specification. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43292D 3.3 Construction and assembly. The end item shall conform to the requirements of this document and to the designs, d
18、etails, and dimensions shown or specified on the applicable drawings, 33.1 Stitching, Stitching shall conform to FED-STD-751. Stitch types shall be as specified on the applicable drawing. Thread breaks, bobbin runouts, or two or more consecutive skipped stitches shall be overstitched not less than 1
19、/2 inch each end, except for type 308 stitching, which shall be overstitched two or three stitches, Runoffs shall be restitched to conform to the required stitch pattern, Backstitching is not required when ends of type 301 stitching are turned under in a hem or held down by other stitching, Thread t
20、ension shall be maintained so that there will be no loose stitching resulting in a loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewed, The lock will be imbedded in the materials sewed. All thread ends shall be trimmed, 3.3.1.1 Automatic stitching,
21、 Automatic stitching machines may be used to perform any of the required stitch patterns provided the requirements for stitch pattern, stitches per inch, and size and type of thread are met, and at least three or more tying, overlapping, or backstitches are used to secure the ends of the stitching,
22、3.4 Workmanship. The end item shall conform to the quality of product established by this specification. 4 QUALITY ASSURANCE PROVISIONS 4,l Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection
23、 requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The
24、Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and
25、 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies sub
26、mitted to the Government for acceptance comply with all requirements of the contract, Sampling inspection, as part of-manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective msterial, either indicate
27、d or actual, nor does it commit the Government to accept defective material. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Ll3272D I6 7777906 0375736 5 MIL-S-43292D 4.1.2 Responsibility for dimensional requirements. Unless otherwise specifi
28、ed in the contract or purchase order, the contractor is responsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the -manufacturing process necessary to ensure compliance with
29、all dimensional requirements. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 3.1 and 6.3
30、), it shall be examined for the defects specified in 44.2 and 4.4.3. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials sh
31、all be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.2 End item visual examination. The end items shall be examined for the defects listed in table I. The
32、 lot size shall be expressed in units of static lines or connector web assemblies, as applicable. The sample unit shall be one static line or one connector web assembly, as applicable. The inspection level shall be II (see 6.5). TABLE I. End item visual defects Classification Examine Defect Major Mi
33、nor Mat er ia1 s Not specified type, class, or size 101 Webbing, duck Color not as specified and tape Cut, hole, tear, abrasion, or Ends not seared or wax dipped Edge beaded or corded weak area as specified 20 1 102 202 203 5 Provided by IHSNot for ResaleNo reproduction or networking permitted witho
34、ut license from IHS-,-,-MIL 43-4 32 92 D TABLE I. End item visual defects (contd) - Classification Examine Defect Major Minor Thread Cord Hardware (as applicable) Construction and workmanship Not speaified type or size Not speaified color Any splice, or not continuous (type i or i static line) Any s
35、plice, or not continuous (type II static line) Ends not seared where specified Core not removed (type II static line 1 Knots insecure, not as specified, or not located as shown on the drawing Any cut or break Not type or size specified Sharp, burred, or split edges Component fractured, malformed, An
36、y area of rust or corrosion Coating blistered, peeling flaking, or otherwise not adherent or bent Screw not seated Not material specified Knife blade does not pivot freely as specified Any component missing, mis- aligned, or not joined as specified Grease, oil dirt, or other foreign matter on surfac
37、e of webbing Stitches and Wrong type stitching Any open seam NOTE: A seam shall be classified as open when one or more stitches joining a seam are broken or two or more consecutive skipped stitches occur. Repairs of open seams shall not be scored as defects. 1 o3 204 104 105 106 1 O7 108 109 110 111
38、 112 20 5 20 6 207 208 209 113 21 o 114 115 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Ll3272D 26 m 7999706 0375738 7 m MIL -S -432 92 D TABLE I. End item visual defects (contd) Cla s si fi cati on Examine Defect Major Minor Stitches and
39、 One stitch per inch less than or stitching (contd) more than the minimum or maxi- mum specified Two or more stitches per inch less than or more than the minimum or maximum specified NOTE: Variation in number of stitches per inch caused by the operator speeding up the machine and pulling the fabric
40、to sew over heavy places, heavy seams, or in turning corners shall be classified as follows: a. Within the major defect classi- fication - Minor defect b. With the minor defect classi- fication - No defect 21 1 116 Stitching ends backstitched less than 1/2 inch (except where ends are turned under in
41、 a hem or held down by other stitchings) 117 Needle chews or holes Thread ends not trimmed 118 Any missing or incomplete row of stitching 119 Tension loose resulting in a loose top or bobbin thread, or tension tight resulting in puckering Runoff at edge and not restitched Thread breaks and skips not
42、 over- stitched as specified Identifica tion Missing, incorrect, or illegible marking Improper location, wrong color or otherwise not as specified 21 5 120 121 21 2 21 3 21 4 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Ll329ZD 16 9999906
43、0195939 O W MIL 1s -432 92 D 4.4.3 End item dimensional examination. The end items shall be examined for conformance with overall length, loop length and locator dimensions, bridle length, and locator dimensions and location of the rigging markings of the statio lines specified on the drawings. Any
44、dimension not within the specified tolerance shall be classified as a defect. units of static lines or connector web assemblies, as applicable. unit shall be one static line or one connector web assembly, as applicable. The inspection level shall be S-3 (see 6.5) . The lot size shall be expressed in
45、 The sample 4.4.4 Packaging examination. The fully packaged end items shall be examined for the defects listed below. shipping containers. packaged. The inspection level shall be S-2 (see 6.5). The lot size shall be expressed in units of The sample unit shall be one shipping container fully Examine
46、Defect Marking (exterior Omitted; incorrect; illegible; of improper and interior) size, location, sequence, or method of application Materials Workmanship Content Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete sealing or closure of flap,
47、 improper taping, loose strapping or inadequate stapling Bulged or distorted container Number per interior pack or exterior container not as specified 4.4.5 Pal1etization.examination. The fulIy packaged and palletized end items shall be examined for the defects Usted below. The lot size shall be exp
48、ressed in units of palletized unit loads. The sample unit shaIl be one pailetized unit load, fully packaged. The inspection level shall be S-1 (see 6.51 b Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Pallet pattern not as specified Interlocking of
49、 loads not as specified Load not bonded as specified Palletization 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-S-43292D Lb m 777970b 0375940 7 m 5.1.1 Level A preservation. Ii Examine MIL -S -432 92D Defect Height a Marking Exceeds maxmum load limits Omitted; incorrect; illegible; of improper size, location, sequence, or method of appl
