1、MIL-PRF-32049 (AR)23 September 1999PERFORMANCE SPECIFICATIONPALLET, FIELD ARTILLERY PROJECTILEThis specification is approved for use by the US Army Armament, Research, Development andEngineering Center, and is available for use by all Departments and Agencies of the Department ofDefense.1. SCOPE1.1
2、Scope. This specification covers the requirements for three types of pallets used for storingand transporting 155MM projectiles. ( see 6.1).1.2 Classification. Classify the field artillery projectile pallet as follows:TYPE I - Field Artillery Projectile Pallet with chemical agent resistance, increas
3、ed durability,reusability and non-combustible which meets all requirements of this specification for a single lengthprojectile.Style A M107 FamilyStyle B M795 FamilyStyle C M549 FamilyStyle D M864 FamilyTYPE II - Field Artillery Projectile Pallet which meets all requirements of this specification fo
4、r alllength projectiles, except 3.3.3, 3.3.4, 3.4.7, 3.5.2, and 3.5.4. Assemble this pallet with steel strapping.TYPE III - Field Artillery Projectile Pallet with chemical agent resistance, increased durability,reusability and non-combustible which meets all requirements of this specification for al
5、l lengthprojectiles.AMSC N/ A FSC 8140DISTRIBUTION STATEMENT A : Approved for public release; distribution unlimited.INCH - POUNDBeneficial comments (recommendations, additions, deletions) and any pertinent data which may be of usein improving this document should be addressed to: Commander, US Army
6、 Armaments Research,Development and Engineering Center, ATTN: AMSTA-AR-QED, Picatinny Arsenal, NJ 07806-5000 orby using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearingat the end of this document or letter.Provided by IHSNot for ResaleNo reproduction or netwo
7、rking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)22. APPLICABLE DOCUMENTS2.1 General . The documents listed in this section are specified in sections 3 and 4 of thisspecification. This section does not include documents cited in other sections of this specification orrecommended for ad
8、ditional information or as examples. While every effort has been made to ensure thecompleteness of this list, document users are cautioned that they must meet all specified requirementscited in sections 3 and 4 of this specification, whether or not they are listed.2.2 Government documents .2.2.1 Spe
9、cifications, standards, and handbooks . The following specifications, standards, andhandbooks form a part of this document to the extent specified herein. Unless otherwise specified, theissue of these documents are those listed in the issue of the Department of Defense Index ofSpecifications and Sta
10、ndards (DODISS) and supplement thereto, cited in the solicitation (see 6.2).STANDARDSFEDERALF ED-STD-595 Colors Used In Government ProcurementFED-STD-101 Test Procedures for Packaging MaterialsMILITARYMIL-STD-810 Environmental Test Methods and EngineeringGuidelinesMIL-STD-1916 DoD Preferred Methods
11、for Acceptance of ProductSPECIFICATIONSMILITARYMIL-PRF-63460 Lubricant, Cleaner and Preservative for Weapons andWeapons Systems(Unless otherwise indicated, copies of the above specifications, standards and handbooks are availablefrom the Standardization Documents Order Desk, Building 4D, 700 Robbins
12、 Avenue, Philadelphia, PA19111-5094)2.2.2 Other Government documents, drawings, and publications . The following otherGovernment documents, drawings, and publications form a part of this document to the extent specifiedherein. Unless otherwise specified, the issues are those cited in the solicitatio
13、n. See section 6.5.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)3DRAWINGUS ARMY TACOM-ARDEC8794342 Seal, Metallic, Assembly, Details and Instruction forApplication(Copies of this drawing are available from US TACOM -ARDEC, AMSTA-
14、AR-QAD, Picatinny Arsenal,NJ 07806-5000)SPECIFICATIONA-A-208 Commercial Item Description Ink, Marking, Stencil,Opaque (Porous and Non-Porous Surfaces)(Copies of this specification are available from Standardization Documents Order Desk, Building 4D, 700Robbins Avenue, Philadelphia, PA 19111-5094)US
15、ARMY DEFENSE AMMUNITION CENTER AND SCHOOL (USADACS)19-48-4076 Bundling of Separate Loading Projectiles for Storage andTransport(Copies of the above drawing are available from US Army Defense Ammunition Center, 1 C Tree Road,Bldg. 35, McAlester, OK 74501-9053)PUBLICATIONSINTERNATIONAL TEST OPERATING
16、PROCEDURESITOP 1-2-601 Labor atory Vibration Schedules dated 1 March 1988(Copies of the above publication are available from US Army Combat System Test Activity, STECS-AD,Aberdeen Proving Ground, MD 21005-5059)TEST OPERATING PROCEDURESTOP 8-2-111 NBC Contamination Survivability, Small Items ofEquipm
17、ent(Copies of the above publication are available from US Army Dugway Proving Ground, STECS-MT-TM-CB, DUGWAY Proving Ground, Dugway UT 84022-5000)EVT-TP-1-86 Transportability Testing Procedures(Copies of the above publication are available from US Army Defense Ammunition Center and School,SIOAC-DET,
18、 Savanna, IL 61074-9639)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)42.3 Non-Government publications . The following documents form a part of this document to theextent specified herein. Unless otherwise specified, the issues of
19、 the documents which are DOD adoptedare those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issuesof documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2).AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI
20、B93.63M Hydraulic Fluid, PetroleumANSI K62.344 Nithiazine InsecticideANSI/SAE AMS 3054A Oil, Lubricating, Low temperature(Address applications for copies to American National Standards Institute, ATTN: Customer Service, 11West 42 nd Street, New York, NY 10036 or http:/www.ansi.org)AMERICAN SOCIETY F
21、OR TESTING AND MATERIALS (ASTM)ASTM B117-95 Operating Salt Spray (Fog) ApparatusASTM E 162-94 Surface Flammability of Materials Using a Radiant HeatEnergy SourceASTM D235 Standard Specification for Mineral Spirits (PetroleumSpirits) (Hydrocarbon Dry Cleaning Solvent)ASTM D610 Evaluating Degree of Ru
22、sting on Painte d Steel SurfacesASTM E662-95 Specific Optical Density of Smoke Generated by SolidMaterialsASTM E800-95 Measurement of Gases Present or Generated During FiresASTM D1655 Standard Specification for Aviation Turbine FuelASTM D3951 Standard Practice for Commercial PackagingASTM D4175 Stan
23、dard Terminology Relating to Petroleum, PetroleumProducts and Lubricants(Address applications for copies to the American Society for Testing and Materials, 100 Barr HarborDrive, West Conshohocken, PA 19428-2959 or http:/www.astm.org )Provided by IHSNot for ResaleNo reproduction or networking permitt
24、ed without license from IHS-,-,-MIL-PRF-32049 (AR)5SOCIETY OF AUTOMOTIVE ENGINEERS (SAE)SAE J 300 Engine Oil Viscosity ClassificationSAE J 312 Gasoline, Automotive, CombatSAE J 313 Fuel, Diesel, Grade DF-2SAE J 1034 Antifreeze, Ethylene GlycolSAE J 1447 Hydraulic Fluid, Fire-resistant(Address applic
25、ations to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale,PA 15096-0001 or http:/www.sae.org)2.4 Order of precedence . In the event of a conflict between the text of this document and thereferences cited herein, the text of this document takes precedence. Nothing in this docu
26、ment, however,supersedes applicable laws and regulations unless a specific exemption has been obtained.3. REQUIREMENTS3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection inaccordance with 4.1.3.2 Design, materials, and manufacturing processes . Unless
27、 otherwise specified, the selection ofthe design, materials, and manufacturing processes is the prerogative of the contractor as long as allarticles submitted to the government fully meet the operating, interface, ownership and support, andoperating environment requirements specified.3.3 Operating r
28、equirements . Each pallet shall meet the following functional, operational, andperformance requirements.3.3.1 Projectile storage . TYPE I and TYPE III pallets shall be capable of carrying and storingfrom two (2) to eight (8) 155MM artillery projectiles of the same length. TYPE II shall be capable of
29、carrying and storing eight (8) rounds only. TYPE II pallets shall be capable of being strapped with 1 inch steel banding. TYPE III pallets shall be capable of carrying and storing all lengths of projectiles in3.3.1.1. When the pallet is completely closed, the projectiles shall be maintained on the p
30、allet in a verticalorientation, show no noticeable lateral movement, nor allow the release of any of the projectiles,throughout the full operating environment spectrum. The pallet shall provide adequate clearance aroundthe projectile to allow removal and attaching of grommets or flexible rotating ba
31、nd covers. The palletshall hold the projectiles at the lifting plug and the boattail. The pallet shall have a means to preventmetal to metal abrasion/corrosion between the projectile boattail and the pallet base if a metal pallet isused. When the pallet is empty, the pallet shall be able to be disas
32、sembled to minimize space.3.3.1.1 Projectile lengths and dimensions. The interface drawings listed in Table I give the lengthof the projectile, the dimensions of the projectile boattail, the dimensions of the grommet and thedimensions of the lifting plug. These interface dimensions are given to insu
33、re that the pallet properlyinterfaces with the projectile body, boattail and lifting plug.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)6TYPE I: The pallet shall be capable of meeting all requirements when storing projectiles from
34、 oneof the lengths given in Table I below.TYPE II: The pallet shall be capable of meeting all requirements (except 3.3.3, 3.3.4, 3.4.7, 3.5.2and 3.5.4) when storing all projectiles lengths given in Table I below.TYPE III: The pallet shall be capable of storing all projectile lengths given in Table I
35、 below.Table I. Interface drawingsProjectile Family Projectile Body ApproximateLengthProjectile Interface DrawingsStyle A - M107 23.8 inches Figures 1, 2, 3.Style B - M795 29.5 inches Figures 4, 5, 6.Style C - M549 30.6 inches Figures 7, 8, 9.Style D - M864 31.6 inches Figures 10, 11, 12.The project
36、iles have a grommet or flexible rotating band cover (FRBC) attached. The projectile interfacedrawings showing length, boattail dimensions, lifting plug and grommet or FRBC are given in the tableabove.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI
37、L-PRF-32049 (AR)7Figure 1. M107 Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)8Figure 2. M107 Plug Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license fro
38、m IHS-,-,-MIL-PRF-32049 (AR)9Figure 3. M107 Boattail Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)10Figure 4. M795 Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted wi
39、thout license from IHS-,-,-MIL-PRF-32049 (AR)11Figure 5. M795 Plug Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)12Figure 6. M795 Boattail Detailed Interface DrawingProvided by IHSNot for ResaleNo reprodu
40、ction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)13Figure 7. M549 Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)14Figure 8. M549 Plug Detailed Interface DrawingProvided by IHSNot for Re
41、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)15Figure 9. M549 Boattail Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)16Figure 10. M864 Interface DrawingProvid
42、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)17Figure 11. M864 Plug Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)18Figure 12. M864 Bottail
43、 Detailed Interface DrawingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32049 (AR)193.3.2. Ease of use. After projectiles have been placed on the pallet, any lock-down, closure,opening, or release actions shall be able to be accomplished b
44、y one person (Between the 95th percentilemale and 5th percentile female). The pallet shall allow for access and removal of projectiles by graspingthe lifting plug or associated area of the projectile. No tools shall be required to open and close TYPE Iand TYPE III pallets. Common hand tools (such as
45、 strap cutters) are allowed to open and close TYPEII pallets. All pallets shall be designed to minimize the amount of loose pieces (maximum three)required to be removed for projectile access.3.3.3 Color. All pallet surfaces shall be flat green in color. The shade for the interior and exteriorsurface
46、s will match the color chip for green, No. 34094 in accordance with FED-STD-595.3.3.4 Chemical agent contamination survivability. The pallet shall be manufactured usingmaterials which do not degrade after exposure to contaminants and decontaminants such that it wouldpreclude mission accomplishment.3
47、.3.5 Identification . Each pallet shall have at least one area on the top with a minimum of60 sq. inches which is clearly visible when the pallet is fully loaded, that can be painted or marked, and becapable of being marked over, using commercial paints or inks in accordance with ink, stencil, yello
48、w No.33533 Type I or IV of CID A-A-208 with no surface preparation other than cleaning and drying.Marking shall be clear and legible and shall remain on the pallet throughout its logistic life cycle.3.4 Interface requirements . Each pallet shall accommodate the following inputs and interfaces.3.4.1 Weight . The pallet, without projectiles, shall weigh no more than 70 pounds.3.4.2 Dimensions . The assembled p
