1、1 MIL-M-48261 (AR) AMENDMENT U 26 July 1991 SUPERSEDING AMENDMENT 5. . 1 May 1990 MILITARY SPECIFICATION MINES, M718/M741 SYSTEM, METAL PARTS This Amendment forms a, part of Military Specification MIL-P-48261 (AR), dated 4 May 1977, and is approved for use within the U.S. Army Armament, Munitions an
2、d Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense. . PAGE 2 2.1: Delete the following dwgs.: 9277743 - Simulant 9277820 - Simulant, Modified 9277763 - Booster, Simulant PAGE 3 4.3.1: Delete the following parts: Simulant - DWg. 9277743 Simulant,
3、 Modified - Dwg. 9277820 BOOSter, Simulant - Dwg. 9277763 PAGE 5 TABLE I: Delete the following parts and the corresponding examinations and tests: Simulant - DWg. 9277743 Simulant, Modified - Dwg. 9277820 Booster, Simulant - Dwg. 9.277763 1 of 3 FS C ,1345 - DISTRIBUTION STATEMENT A. Approved for pu
4、blic release; distribution is unlimit-d. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-4826L (6) 13 9999906 0486028 L MIL-M-48261 (AR) AMENDMENT 6 PAGE 8 Add the following major defect to paragraph 4.4.2.1: Examination Requirement inspection
5、Paragraph Method Category or Test - AQL Major 114 Radius from ID 0.40% to flange, above max. 3.2 4.5.2 PAGE 9 4 4.2.2.: Add the following major defect “111: Flats along the outside and bottom edges not present, 0.40% 3.2 Visual.“ * Major 109: Delete “Comparator/Gage“ and substitute “Standard Measuri
6、ng Equipment/Tool Control“. PAGE 12 4.4.2.5: Simulant. Delete paragraph in its entirety. PAGE 13 4.4.2.6: Simulant, Modified, Delete paragraph in its entirety. PAGE 14 4.4.2.7: Add the following major defect: “105 Chamfer above max. 0.40% 3.2 Gage“ * Minor 202: Under examination or test column, chan
7、ge to read “Thickness of ring below notch (2), improper“. PAGE 15 4.4.2.8: Booster, Simulant. Delete paragraph in its entirety. PAGE 19 4.4.2.12: Pad spherical, Add Major 101 “Material improper/ Hardness improper, - - , 3.1, Certification“. 2 Provided by IHSNot for ResaleNo reproduction or networkin
8、g permitted without license from IHS-,-,-MIL-M-48261 (AR) AMENDMENT 6 PAGE 26 4.4.3.2: Density of the simulant. Delete paragraph in its entirety . PAGE 27 4.5.2: Density o simulant, Delete paragraph in its entirety. Add paragraph 4.5.2: “4.5,2 Inspection of radius. The internal radius between the bo
9、dy inner diameter and the flange shall be measured on an optical comparator, after having obtained a mold of the interfacing surface using a quick sekting plaster of similar material.“ * 5.1.1: Delete “Level C“ and substitute “Level B“. Add the following to end of paragraph: “For Body and for wire b
10、ound boxes, a mandatory filler shall be provied for all surfaces.“ The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were.made. This was done as a convenience only and t
11、he Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relation to the last previous amendment. Custodian: Army-AR O Preparing activity: Army- AR (Project 1345-A603) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
