1、m-C-51361B( EA) 20 October 1976 SUPERSEDING MIL-C-51361A( EA) 7 June i976 MTLITARY SPECIFICATION CANISTER, SMOKE, HC, 105m PROJECTILE, M1, COMPONENTS FOR This specification is approved for use by Edgewood Arsenal, Department of the Army, and is available for use by all Depart- ments and Agencies of
2、the Department of Defense, I. SCOPE 1.1 2. APPLICABLE DOCUMENTS This specification covers the components for one type of canister. 2.1 Government documents. The following documents of the issue in effect on date of invitation for bids or request for proposai, form a Fart of this specification to the
3、 extent specified herein: SPEC IF1 CATIONS FEDERAL PPP-B-587 - BOX, Wood, Wirebound PaJlet Type. PPP-F-320 - Fiberboard; Corrugated and Solid, Sheet Stock (Con- tainer Grade) and Cut Shapes. MILITARY MIL-A-2550 - Ammunition, General Specification For. STANDARDS mDERAL Fed-Std-141 - Paint, Varnish, L
4、acquer and Related Materials, Methods of Inspection, Sampling and Testing, FSC 1315 : Beneficial comments (recommendations, additions, deletions) and any : : pertinent data which may be of use in improving this document should : : be addressed to: Commander, Edgewood Arsenal, Attn: SAREA-TS-S, : Abe
5、rdeen Proving Ground, 10 : Standardtzation Document Improvement Proposal (DD Form 1426) appear- : - ing G? the end of this document or by letter. 21010 by using the self-addressed PAGES. - , , . -. $s y Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
6、-MIL-C- 51361 (EA) MILITARY MIL-STD-105 - Sampling Procedures and Tables. for Inspection by Attributes. MIL-STD-129 - Marking for Shipment and Storage, MIL-STD-1167 - Ammunition Data Card. MIL-STD-1168 e Lot Numbering of Ammunition. US ARMY ARMAMENT COMMAND TDPL-15-11-22 - Canister, Smoke, HC, lO5MM
7、 Projectile, Ki; Components for. (Copies of Specifications, standards , drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting offher, ) 3, REQUIREMENTS 3.1 Materials and compo
8、nents. 3,1,1 Materials. All materials cited on TDFL-1.5-U-22 shall conform to the specifications listed thereon or to the specific characteristics set forth on the drawings. 3J.2 Components, All components of the canisters shall conform to the specifications and drawings listed on TDPL-15-ll-22. 3.2
9、 AssembQ. The body and body assembly shall be in accordance with Drawings c15-li-28 and ci5-11-27. 3.3 Welds, The body assembly shall not contain more than three separated projections when tested as specified in 4.4.4,i. 3.4 Prepraduction, Prior to the start of regular production, a pre- production
10、lot shall be produced in accordance with this specification for xamination and test (see 4.3). 3.5 Workmanship. The components shall be free from contamination (foreign matter, oil or grease) ad damage such as dents, cracks or deformation which could affect their intended use. 2 Provided by IHSNot f
11、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-51361B( EA) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. 4.1.1 Suppliers responsibility. Unless otherwise specified in the con- tract or purchase order, the supplier is responsible for the perfo
12、rmance of all inspection requirements as specified herein. specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance 0.f the inspection require- ments specified herein, unless disapproved by the Government. The Govern- ment reserves the rig
13、ht to perform any of the inspections set forth in the specification where such inspections are deemed necessary- to assure sup- plies and services conform to prescribed requirements. 4.1.2 Additional responsibility of supplier . Drawings for contractor Except as otherwise designed inspection equipme
14、nt (other than standard measuring equipment) should be forwarded to design agency for approval prior to production (see 6.2) . Ammunition data cards prepared in accordance with MIL-STD- shall be forwarded with each lo of components. 4.1.3 Government responsibility. a. “he Government will be responsi
15、ble for the performance of the tests to establish the minimum mechanical properties required on Drawing cis-u-28 for the preproduction quantity only. quantity shall be forwarded to the laboratory designated by the contracting officer (see 6.2). Samples from the preproduction b. The canister metal co
16、mponents manufacturer shall be responsible for the performance of the tests to establish the minimum mechanical properties required on Drawing Ci5-11-28 for each canister lot produced during regular production. 4.1.4 Objective evidence. The supplier shall provide objective evidence acceptable to the
17、 contracting officer that the requirements of 3.3. and section 5 for which specific inspection has not been provided in this speci- fication have been satisfied, provided to the contracting officer as proof of compliance of the material specified for the metal components . Specifically laboratory te
18、st data shall be 4.2 Classification of inspections. (a) Preproduction inspection (see 4.3). (b) Quality conformance inspection (see 4.4). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5Z3bZB 13 777770b 03337ZL Z MIL-C- 51361 (EA) 4.3 Prepro
19、duction inspection. 4.3.1 E. A preproduction lot of 500 sets of components (body assemblies, closing disks, packing disks, and zinc sleeves) shall be manufactured using the same methods, materials, equipment, and processes as will be used during regular production. 4.3.2 Sampling. 4.3.2.1 For examin
20、ation. Components sufficient to assemble 50 canisters shall be taken at random from the preproduction lot. In addition, five each of the body (Drawing Ci5-ii-28), tube (flat development) and tube, formed (Drawing CE-11-29) shall be selected at random from the preproduction quant i ty . 4.3,2.2 For d
21、estructive tests b (a) Body assembly. Ten body assemblies (Drawing C15-11-27) shall be taken at random from the preproduction lot, (b) Body. Five bodies (Drawing Cl5-11-28) shall be taken at random from the preproduction lot for testing by the Government (see 4.1.3a). 4.3.3 Inspection procedure. 4.3
22、.3.1 For examination. The sample components shall be examined in accordance with the clascification of defects (4.4.3.3) and MIL-STD-105. The individual bodies, and tube in flat and formed configurations shall be examined for conformance to their respective drawings. number is O. The acceptance 4,3.
23、3.2 For destructive tests. Five body asseniblies shall be tested in assembly shall contain more than Five body assemblies shall be tested in accordance with three separated proJections . shall not exhibit rust beyond i/8 inch from any unpainted edge or score mark. (c) Body, The sample bodies shall b
24、e tested in accordance with Drawing Ci5-11-28. The acceptance number is zero (see 4.1.2). 4.3.4 Acceptance/rejection criteria. The preproduction samples shall comply with 4.3.3 to be acceptable, The supplier shall obtain written . .4 Provided by IHSNot for ResaleNo reproduction or networking permitt
25、ed without license from IHS-,-,-NIL-C-.51361B 13 m 9999906 0333912 3 m approval from the contracting officer prior to proceeding with regular production , 4.4 Quality confornance inspection. 4.4.1 Lottin , Each lot shall be identified and controlled in accordance with MIL-STD-U * 8. A lot shall cons
26、ist of like components or like sub- assemblies of one interfix number, produced by one manufacturer, from the same materials and under essentially the same manufacturing conditions, Mo one lot of any component shall contain steel from more than one heat of : A. Disks shall be packed together in a ma
27、nner which will make use oftheir stacking ability. Sufficient quantities shall be packed together to provide an economical and efficient package and assure safe delivery to a first receiving activity in an undamaged condition. 5.2 Marking. In addition to any special marking required by the con- trac
28、t or order, shipping containers shall be marked in accordance with the domestic marking requirements of MIESTD-129. 6. NOTES 6.1 Intended use. These components are intended for MI. canisters to be used in the 105m HC Smoke Cartridge, M84Al. 8 Provided by IHSNot for ResaleNo reproduction or networkin
29、g permitted without license from IHS-,-,-6.2 Ordering data, Procurement documents should speciw the following: (a) (b) Interplant shipment . The title, number, and date of this specification. (1) Interplant shipment shall be defined as material which will not enter the military supply system. Typica
30、l are shipments of component parts from a vendor to a prime contractor, a subcontractor, or a supplier to a military installation or plant. The responsibility of acceptance of the material is the contractors. (2) Selection of containers cited in 5.1.1.1 and 5.1.1.2 shail be at the option of the proc
31、uring activity and shall be designated in the contract or order. (c) Preproduction. (1) (2) (3) Time allowed for supplier submission of samples for Name and address of test facility and shipping instruc- Time required for the Government to notify the supplier Government test and evaluation after awa
32、rd of contract. tions when testing is performed by the Government. whether or not to proceed with production, (a) Design agency where drawings for contractor designed inspection equipment should be forwarded. Custodian : Preparing activity: Project No. 1315-A285 U. S. GOVERNMENT PRINTING OFFICE 1976 -703.02/50 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
