欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ARMY MIL-C-12095 G-1982 CLOTH WIND-RESISTANT SATEEN COTTON FIRE AND WATER RESISTANT《防火防水防风缎纹棉织物》.pdf

    • 资源ID:441135       资源大小:507.18KB        全文页数:13页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ARMY MIL-C-12095 G-1982 CLOTH WIND-RESISTANT SATEEN COTTON FIRE AND WATER RESISTANT《防火防水防风缎纹棉织物》.pdf

    1、1. SCOPE 1.1 Scope, This document covers one type of sateen cotton cloth which has been treated for flame and water resistance. * 1.2 Classification. The cloth shall be of the Type I - Deleted (see 6.10) Type II - 7.5 - 9,O ounces per square yard 2. APPLICABU DOCUMLNTS * 2.1 Governmeat documents . U

    2、nless otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, forin a part of this document to the extent specified herein. SPECIFICATIONS FEDERAL V-T-276 - Thread, Cotton PPP-P-1134 * . - Packaging and Packing of Cotton and Cotton-

    3、Synthetic Fiber Blend Fabrics (Excluding Duck Fabrics) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Natick Research and Development Laboratories, Natick, MA 01760 by using the self-ad

    4、dressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this docu- ment or by letter. 9 .FSC 8305 THIS DOCUMENT CONTAINS 13 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_- -.- - MIL-C-L2075G 3 m 777770b

    5、 0378030 7 m MIL-C-120956 STANJIARDS . . FEDERAL F ED-STD-4 - Glossary of Fabric Imperfections FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (Copies of documents required by manufacturers in connection with specific acquisition

    6、functions should be obtained from the contracting activity or as directed by the contracting officer.) OTHER GOVERNKENT DOCUMENTS Laws and Regulations Rules and Regulations Under the Textile Fiber Products Identification Act (Copies may be obtained without charge from the Federal Trade Commission, W

    7、ashington, M: 20580.) * 2.2 Other publications. Unless otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 1424 - T

    8、ear Resistance of Woven Fabrics by Falling-Pendulum (Elmendorf .) Apparatus (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 191030) * (Technical society and technical association specifications and standards are genera

    9、lly available for reference from libraries. technical groups and using Federal agencies.) document and the references cited herein, the text of this document shall take precedence. They are also distributed among * 2.3 Order of precedence In the event of a conflict between the text of this 2 Provide

    10、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-12075G 83 U 7777706 0378031 7 U i 3. REQUIREMEWS MIL-C-12095G 3.1 Standard sample. The finished cloth shall match the standard sample for -shade and shall be equal to or better than the standard sample w

    11、ith respect to all characteristics for which the standard sample is referenced (see 6.3). * 3.2 First article. When specified, a sample shall be subjected to first article inspection (see 4.3, 6.2 and 6.4). 3.3 Material (see 6.11). 3.3.1 - Yarn. The yarn shall be made from cotton which has been card

    12、ed, combed, spun and twisted into either 2 or 3 ply yarns in the warp and filling (see 4.4.3 and 6.8) a 3.4 Color. The color shall be as specified and shall match the standard sample (see 6.2, 6-3 and 6.5). The use of dyes and compounds containing elementary sulfur capable of oxidation to sulfuric a

    13、cid is prohibited. The dyestuff shall be chosen and applied so that the dyed and finished cloth shall contain no more labile sulfur than shown by the standard sample when tested as specified in 4.4.3. When no standard sample is available, the dyed cloth shall show no more than a slight trace of labi

    14、le sulfur as defined in the test method when tested as specified in 4.4.3. * 3.4.1 Matching. The color of the face side shall match the standard sample under artificial daylight having a color temperature of 7000 + 500 kelvin and shall be a good approximation to the standard sample under incandescen

    15、t lamplight at 2850 + 100 kelvin. J -_ 3.4.2 Colorfastness. The ftnished cloth shall show colorfastness to weathering and crocking equal to or better than the standard sample when tested as specified in 4.4.3. When no standard sample is available or when the standard sample is not referenced for col

    16、orfastness, the finished cloth shall show “good“ colorfastness to weathering and shall show no more crocking on dry white cloth than Munsell Value 7.0 when tested as specified in 4.4.3. * 3.5 .Physical requirements. The finished cloth- shall conform to the physical. requirements specified in table I

    17、 when tested as specified in 4.4.3. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-L2095G 3 m 777770b 0378032 O m MIL-C-12095G TABLE I. Physical requirements . Weight, (OZ. per sq/yd.): Minimum Maximum Yarns per inch, (min.): Warp Pilling .

    18、 - Type II 7.5 9.0 104 88 Breaking s-trength, pounds (min.): Warp 170 Filling 150 Tearing strength, pounds (min.): Warp Filling 6. O 6. O * 3.5.1 - Weave. shown on figure 1. 3.5.2 - Width. The weavewill be a 5-harness warp sateen with a counter of 2 as The use of fly-shuttle orla shuttleless loom is

    19、 permitted. * The width of the finished cloth shall be as specified (see 6.2) and shall be the minimum acceptable width inclusive of selvages. woven on shuttleless looms, the width measurement shall be made between the last warp yarn on each side, and the protruding fringe(s) are excluded. When the

    20、cloths are 3.5.3 Cloth preparation. The cloth shall be closely singed and mercerized. The cloth shall contain not more than 2.0 percent starch and protein content including chloroform-soluble and water-soluble material prior to water and fire resistant treatment when tested as specified in 4.4.3. 3.

    21、6 Finish. The cloth shall be given an approved finish (see 6.6). * 3.6.1 Water repellent treatment. The cloth shall be given an approved durable water repellent finish. specified in not less than 90, 90, 80 initially, and not less than 70, 70, 70 after 150 hours exposure to weathering when tested as

    22、 specified in 4.4.3. The finished cloth shall conform to the requirements table II, and spray ratings of the three individual determinations of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- NIL-C-LZ095G 83 m 9999906 0378033 2 MIL-C-12095C TABL

    23、E SI. Water repellency and air permeability requirements -. ydrostatic pressure in centimeters minimum (average) - 1/ Percent dynamic absorption (2Odnute time interval) maximum (average) Air permeability (cubic feet per minute per square foot) maximum (average) .Type II 45 25 .3* 0 - 1/ Low pressure

    24、 range; no single determination shall fall below 40 cm. 3.6.2 Flame resistance. The cloth shall be given an approved durable flame- resistant treatment (see 6.6). The finished cloth shall have an after flame of not more than 2.0 seconds and an average char length of not more than 5.0 inches before a

    25、nd after three cycles of laundering when tested as specified in 4,4.3. 3,7 pH. The pH value of the water extract of finished cloth shall be no less than 5.0 nor more than 8.5 when tested as specified in 4.4.3. 3.8 Dimensional stability. The cloth shall not shrink or elongate more than 4.0 percent in

    26、 either the direction of the warp or filling when tested as specified in 40-4.3. 3.9 Seam efficiency. The finished cloth shall have a seam efficiency of not less than 60 percent when tested as specified in 4.4.3. 3.10 Face identification. The face side of the cloth shall be identified by applying a

    27、stamping on that side of the cloth with the word “Face“ at each end of the piece. .3,11 Length and put-p. Unless otherwise specified (see 6.2), the cloth shall be furnished in continuous lengths, each not less than 40 yards. putup on rolls as specified in PPP-P-1134. The cloth shall be 3.12 Fiber id

    28、entification. Each roll shall be labeled and ticketed for fiber content in accordance with the Rules and Regulations Under the Textile Fiber Products Identification Act. 3.13 Workmanship. this document. specified in section 4, shall not exceed the established maximum point values. The finished cloth

    29、 shall conform to the quality established by The demerit points per 100 square yards, when calculated as 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-12095G MIL-C-12075G 3 7777906 0378034 Li 4. QWALITY ASSURANCE PROVISIONS . 4.1 Responsibi

    30、lity or inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilit

    31、ies suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. inspections set forth in the document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. The Government reserve-s the r

    32、ight to perfprm any of the 4.1.1 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. * 4.2 Classification of inspection. The inspection requirements specified herein are

    33、classified as follows: a. First article hspection (see 4.3). b. Quality conformance inspection (see 4.4). * 4.3 First article inspection. When a first article is required (see 6.2), it shall be examined for the defects specified in 4.4.2.1 and 4.4.2.3 and tested for the characteristics specified in

    34、4.4.3. any test shall be cause for rejection of the first article. The presence of any defect or failure of 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordanc

    35、e with 4.1 components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this docu- ment or applicable purchase document. 4.4.2 End item examination. 4.4.2.1 Yard-by-yard examination. Each rol

    36、l in the sample shall be examined on When the total yardage in the roll does not exceed 100 yards3 the face side only. the entire yardage in the roll shall be examined. roll exceeds 100 yards, only 100 yards shall be examined. All defects as defined in section 1 of FED-STD-4 which are clearly notice

    37、able at normal inspection distance (3 feet) shail be scored and assigned demerit points as listed in 4.4.2.1.1 except that only those slubs and knots which exceed the limits shown on figure 1 of FED-STD-4 shall be scored. No linear yard (increments of 1 yard on the measuring device of the inspection

    38、 machine) from any one roll within the sample shall be penalized more than 4 points. The sample size shall be 20 rolls selected from 20 containers. total yardage examined exceeds 30 points. When the total yardage in the The lot shall be unacceptable if the points per 100 square yards of the The lot

    39、shall be unacceptable if the -6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-C-12095G 3 I 9779906 O378035 b I M1t-C-12095G points per 100 square yards f two or more individual rolls exceeds 45 points. If one roll exceeds 45 points per .lo0 s

    40、quare yards, a second sample of 20 rolls shall be examined only for individual roll quality. or more rolls in the second sample exceeds 45 points per 100 square yards. .computation for lot quality and individual roll quality shall be as follows: The lot shall be unacceptable if one. Point Points per

    41、 100 square yards Total points scored in sample size x 3600 I Contracted width of cloth (inches) x total yards inspected 4.4.2.1, 1 Demerit points. Demerit points shall be assigned as -follows : For defects 3 inches or less in any dimension - one point For defects exceeding 3 inches but not exceedin

    42、g 6 inches in any dimension - two points For- defects exceeding 6 inches but not exceeding 9 inches in any dimension For defects exceeding 9 inches in any- - three points dirnens ion - four points The following defects, when present, shall be scored four points for each yard in which they occur: Bag

    43、gy, ridgy, or wavy cloth Objectionable odor Width less than specified Cloudy, mottled, or streaky color Not closely singed Excessive neppiness 4.4.2.2 Length examination. 4.4.2.2.1 Individual rolls. During the yard-by-yard examination, each roll in the sample shall be examined for length. minimum sp

    44、ecified or more than 2 yards less than the length marked on the ticket shall be considered a defect with respect to length. if two or more rolls in a sample are defective in respect to length. Any length found to be less than the The lot shall be unacceptable 4.4.2.2.2 Total yardage in sample. The l

    45、ot shall be unacceptable if the total of the actual lengths of rolls in the sample is less than the total of the lengths marked on the tickets. 4.4,2.3 Shade examination. During the yard-by-yard examination, each roll in the sample shall be examined for shade. Any roll in the sample off shade, shade

    46、d side to side, side to center, or end to end shall be cause for rejection of the entire lot represented by the sample. ,7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. _ 1- - MIL-C-LZ075G 83 I 7974906 037803b 8 MIL-C-12095G 4,4.2.4 Examination f

    47、or compliance with Textile Fiber Products Identification Act The lot shall be unacceptable if two or and face marking. shall be examined for defects listed below. more of the following defects are present in the sample: miring the yard-by-yard examination, each roll in the sample Not labeled or tick

    48、eted in accordance with the Rules and Regulations Face stamping missing from either or both ends. Face stamping on wrong side. Under the Textile Fiber Products Identification Act. * 4.4.3 End item testing. The cloth shall be tested for characteristics listed in table III. and as listed in table III

    49、shall be followed. specified in section 3 apply to the results of the determinations made on a sample unit for test purposes as specified in the applicable test method. shall be 1/2 yard full width-of the cloth prior to fire and water resistant treatments and 5 continuous yards full width of the finished cloth, (number of sample units) shall be as shown below. in units of 1 yard. to meet any of the requirements specified. indi


    注意事项

    本文(ARMY MIL-C-12095 G-1982 CLOTH WIND-RESISTANT SATEEN COTTON FIRE AND WATER RESISTANT《防火防水防风缎纹棉织物》.pdf)为本站会员(eventdump275)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开