1、MIL-C-11504C (MU) 1 October 1964 SUPERSEDING 12 April 1963 MIL-C-11504B (MU) MILITARY SPECIFSCATION CHARGE, DEMOLITION, BLOCK, INERT, 1 POTJND Pm AND LOADING, ASSEMBLING AND PACKINQ 1. SCOPE 1.1 This specification covers the quality assurance provisions, and requirements not covered by the drawings,
2、 for the parts and loading, assembling and packing for one type of practice item designated as Charge, Demolition, Block, Inert, 1 Pound. 2. APPLICABLE DOCUPIENTS 2,l The following documents of the issue in effect on the date of invitations for bids, or request for proposals, form a part of this spe
3、cification to the extent specified herein. SPECIFICATIONS MILITARY MIL-A-2550 - Ammunition and Special Weapons; General Specification for. MIL-P-10025 - Packaging, Packing and Marking for Interplant Shipment of Inert Ammuni%ion Components, General Specification for. MIL-1-45208 - Inspection Requirem
4、ents; General Specification for. MIL-1-45607 - Inspection Equipment; Supply and Maintenance of. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (ABC-STD-105). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
5、,-MIL-C-11504C (MU) MIL-STD-109 - Quality Assurance Terms and Definitions. MIL-STD-1235 - Single and Multilevel Continuous Sampling Procedures and Tables for Inspection by Attributes, DRAWINGS ORDhkWCI.3 CORPS 8886602 - Charge, Demolition, Block, 1 lb., Inert PUBLICATIONS ORDNANCE CORPS IEL-8886602
6、- Index of Inspection Equipment Lists. (Copie8 of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer). 3. FEQUIREMENTS 3.1 Material.-Mate
7、rials and parts shall be in accordance with applicable drawings and specifications. 3.2 Inert charge assemblies.-The inert charge assemblies shall comply with all requirements specified on Drawing (dwg.) 8886602 and with all requirements specified in applicable specifications. neither end shall pene
8、trate the outer layer of paper. and finished in a thorough, workmanllke manner. They shall be free of burrs, sharp edges, surface defects, dirt, grease, rust, corrosion products, and other foreign matter. The cleaning method used shall not be injurious to any part nor shall the parts be contaminated
9、 by the cleaning agent. Surface coatings shall be continuous except for a few light scratches not exposing base material. 3.3 Crimping.-During the crimping operation, the edge of 3.4 Workmanship.-All parts and assemblies shall be fabricated All required marking shall be neat and sharply defined. 2 P
10、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-11504C (MU) 4. QUALITY ASSURANCE PROVISIONS 4.1 General quality assurance provisions.-Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance o
11、f all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspe
12、ctions are deemed necessary to assure supplies and services conform to prescribed requirements. Reference shall be made to Standard MIL-STD-109 in order to define terms used herein. The provisions of Specification NL-A-2550 shall apply. 4.1.1 Contractor quality assurance system.-The contractor shall
13、 provide and maintain an effective quality assurance system in compliance with the requirements of Specification MIL-1-45208. The contractors quality assurance system shall contain a procedure for the reporting of critical defectives found during the course of his Inspection and during inspection by
14、 the Government. Any critical defect encountered, unless annotated by an asterisk (*) to the right of the characteristic code number (see 6.2), will be reported within 48 hours. critical defects annotated by an asterisk will be furnished. The agencies to whom the reports will be furnished are identi
15、fied in paragraph 6.5. The reports shall contain, as a minimum, the following infomaation: A monthly sununary report covering those a. Contractor and contract number. b. Number and revision date of specification. c. Characteristlc code number. d. Lot or serial number. e. Number of defectives found.
16、f. g. Corrective action taken or recommended. When the Assignable cause or analysis of occurrence. corrective action ks beyond the control of the contractor or the scope of the contract, the report shall contain the contractors recommendation to the Government. 4.1.2 Submission of product.-At the ti
17、me the completed lot of product is submitted to the Government for acceptance the contractor shall supply the following information accompanied by a certificate which attests that the information provided is correct and applicable to the product being submitted: 3 Provided by IHSNot for ResaleNo rep
18、roduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2.2 Examination.-Sampl5n dmensions, materials, finish, notes, operating and calibration instructions be properly depicted in accordance w
19、ith approved practices to the extent that further calculation or clarification will not be required. Contractor designa identified as CDCP may be developed on the format the contractor normally employs in his equipment design procedure provided such formt reflects the detail and information specifie
20、d above. shall comply ulth the format and requirements of ML-45608, and In addition, contain the detail and Information specified above. submitted for approval to the Commandlsig Officer, Picatinny Arsenal, ATTN: SMPA-ND. Design review will nolly be accomplished nithin one month after receipt by Pic
21、atinny Arsenal. Partial submission of inspection equipnent designa is permissible and encouraged. However, the Arsenal completion date for design review will be based on the date of the final submission of designs. 6.4 Submission of initial Production, Pre-Production OF Qualification Samples.=Instru
22、ction, as to the location for the evaluation of Initial Production, Pre-production, or product qualification shall be obtained from the contracting officer. receipt of such request, the contracting officer shall advise Picatinny Arsenal and instructions will be Issued according3y. inquiries should b
23、e fomarded to: Arsenal, ATTN: SMPA-Ni. Contractor designs shall be Contractor designa identified a8 CDAF 6.3.7 Submission of contractor designs.-Designs swll be Vpon All Coamanding Officer, Picatinny 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
24、-I MIIrC-11504C (MU) 6.5 Submission of critical defect reporta.-For U. S. Army Munitiono Camand procurements, one copy of each critical defect report will be furnished the cognizant Qovernment inspection agency; tho Amy Amunition Procurement and Supply Agency, ATTN: SWAP-ROJ PlCatinny ATBbll81, Amt
25、WPAM). 6.5.1 Reporting to other aervice.-For other than U, S. Army Munitions cw procurmonta,-crritIcal detect reporting shall be as prescribed by the Contracting Officer. Custodian: Anipy-m . meparing activity: W-MU ! L i 1. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
