欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ANSI INCITS ISO IEC 7811-6 AMD 1-2005 Identification cards Recording technique Part 6 Magnetic stripe High coercivity Amendment 1 Ui6 criteria and test method.pdf

    • 资源ID:436459       资源大小:513.45KB        全文页数:8页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ANSI INCITS ISO IEC 7811-6 AMD 1-2005 Identification cards Recording technique Part 6 Magnetic stripe High coercivity Amendment 1 Ui6 criteria and test method.pdf

    1、INCITS/ISO/IEC 7811-6:2001/Amd.1:20052008 (ISO/IEC 7811-6:2001/Amd.1:2005, IDT) Identification cards Recording technique Part 6: Magnetic stripe High coercivity Amendment 1: Ui6criteria and test methodINCITS/ISO/IEC 7811-6:2001/Amd.1:20052008(ISO/IEC 7811-6:2001/Amd.1:2005, IDT)INCITS/ISO/IEC 7811-6

    2、:2001/Amd.1:20052008 ii ITIC 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the compu

    3、ter performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to creat

    4、e this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the

    5、Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 6/30/2008 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyri

    6、ght 2008 by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technolo

    7、gy Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005.

    8、Printed in the United States of America INCITS/ISO/IEC 7811-6:2001/Amd.1:20052008 ITIC 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. Nati

    9、onal bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest

    10、. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the

    11、 rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires

    12、 approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO/IEC 7811

    13、-6:2001 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. INCITS/ISO/IEC7811-6:2001/Amd.1:20052008 ITIC 2008 All rights reserved 1Identification cards Recording technique Part 6: Magnetic stripe High coercivity AME

    14、NDMENT 1: Ui6criteria and test method page v, Foreword Add the following after point 5: 6. The algorithm defined in Figure 7 of ISO/IEC 7811-6 has been changed to produce more consistent results. page 8, subclause 7.3, Table 1 In the Requirement column for the Waveform row, replace “Ui6u 0,05 UA6” w

    15、ith “Ui6u 0,07 UA6”. Add a row above the note at the end of the table for the following text: “Use test method in Annex E for waveform criteria.” Add the following sentence to the existing note: “These values are for unencoded card tests and are not applicable for encoded cards.” INCITS/ISO/IEC 7811

    16、-6:2001/Amd.1:20052008 2 ITIC 2008 All rights reservedPage 9, subclause 7.3, Figure 7 Replace the figure with the one shown below. Ui6Last 0 cross point Midpoint between adjacent peaks Midpoint between adjacent peaks a 1,5a Ui6measurement area for Ui6Last 0 cross point Last 0 cross point Last 0 cros

    17、s point a 1,5a measurement area for Ui61. Find midpoint between 2 adjacent peaks. 2. Find 0 crossing point for waveform between midpoint and adjacent peak. 3. The measurement area is 1,5 times the distance between the midpoint and 0 cross point. 4. Find the largest signal amplitude level in the meas

    18、urement area defined in the figure. 5. The absolute value of this level is the Ui6for the waveform. INCITS/ISO/IEC 7811-6:2001/Amd.1:20052008 ITIC 2008 All rights reserved 3Page 23 Add the following annex after Annex D. Annex E (normative) Waveform Ui6test method E.1 Purpose The purpose of this test

    19、 is to determine the degree of waveform distortion present in the read back waveform when recorded under the specified conditions. NOTE This test method will be included in the next published version of ISO/IEC 10373-2 (currently under revision). E.2 Apparatus The test shall be conducted using the a

    20、pparatus specified in ISO/IEC 10373-2 for Amplitude measurements against this standard. E.3 Procedure Perform the entire sequence of measurements on the same equipment and under the same conditions. The read pass upon which measurements are made shall be performed while reading in the same direction

    21、 as recording. Only the traverse necessary to restore the card to its start position shall intervene between the recording pass and the read pass upon which the measurements are performed. Record and read the card under the conditions specified in the base standard, with the following additional con

    22、straints: a) Encode flux transitions at the density specified in Table 1 across the full length on the card in the track 2 position. b) Determine and record the value of the average amplitude UA6. c) Using the procedure in the base standard, find the largest value of Ui6for the card and record this as the Ui6value. E.4 Test report The report shall give the quantity values obtained and shall state whether or not the result conforms to the requirements of the base standard.INCITS/ISO/IEC 7811-6:2001/Amd.1:20052008 ICS 35.240.15 Price based on 3 pages ITIC 2008 All rights reserved


    注意事项

    本文(ANSI INCITS ISO IEC 7811-6 AMD 1-2005 Identification cards Recording technique Part 6 Magnetic stripe High coercivity Amendment 1 Ui6 criteria and test method.pdf)为本站会员(deputyduring120)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开