1、 IEEE Standard Supplement for Strapdown Applications to IEEE Standard Specification Format Guide and Test Procedure for Single-Degree-of-Freedom Rate-Integrating Gyros Corrigendum 1: 3.3.9.2.2, 3.6.4.1.1, 3.6.4.1.2, 6.3, and 10.10.4.1 Sponsored by the Gyro and Accelerometer Panel IEEE 3 Park Avenue
2、New York, NY 10016-5997 USA IEEE Aerospace and Electronic Systems Society IEEE Std 529-1980/Cor 1-2017 IEEE Std 529-1980/Cor 1-2017 IEEE Standard Supplement for Strapdown Applications to IEEE Standard Specification Format Guide and Test Procedure for Single-Degree-of-Freedom Rate-Integrating Gyros C
3、orrigendum 1: 3.3.9.2.2, 3.6.4.1.1, 3.6.4.1.2, 6.3, and 10.10.4.1 Sponsor Gyro and Accelerometer Panel of the IEEE Aerospace and Electronic Systems Society Approved 28 September 2017 IEEE-SA Standards Board 2 Copyright 2017 IEEE. All rights reserved. Abstract: Corrections are made by this corrigendu
4、m to material already published in IEEE Std 529-1980. Keywords: corrigendum, IEEE 529 The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2017 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 2
5、6 October 2017. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to:
6、results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and ser
7、vices related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards
8、 available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own indep
9、endent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CON
10、SEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WA
11、Y OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. 4 Copyright 2017 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents i
12、n English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall
13、 not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make i
14、t clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IE
15、EE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it i
16、s important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases whe
17、re the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following
18、 address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable reg
19、ulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed
20、as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in
21、 private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the app
22、ropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, 5 Copyright 2017 IEEE. All rights reserved. non-commercial use only. To arrange for payment of licensing fees, please contac
23、t Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents User
24、s of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current editi
25、on of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although st
26、ill of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amend
27、ments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/ or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all
28、 IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of sub
29、ject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assuranc
30、e, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable ter
31、ms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license m
32、ay be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of
33、 this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2017 IEEE. All rights reserved. Partici
34、pants The following individuals on the Gyro and Accelerometer Panel were major contributors to this standard: Randall Curey, Chair Reese Sturdevant, Vice Chair George Erickson Robert Martinez Edward Schlatter Leroy Thielman The following members of the individual balloting committee voted on this st
35、andard. Balloters may have voted for approval, disapproval, or abstention. Cleon Barker Jason Bingham Keith Chow Randall Curey George Erickson Randall Groves Werner Hoelzl Jean-Francois Kieffer Robert Robinson Walter Struppler Leroy Thielman When the IEEE-SA Standards Board approved this standard on
36、 28 September 2017, it had the following membership: Jean-Philippe Faure, Chair Gary Hoffman, Vice Chair John D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfin
37、ger* Kevin Lu Daleep Mohla Damir Novosel Ronald Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Yu Yuan *Member Emeritus 7 Copyright 2017 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 529-1980/Cor 1
38、-2017, IEEE Standard Supplement for Strapdown Applications to IEEE Standard Specification Format Guide and Test Procedure for Single-Degree-of-Freedom Rate- Integrating GyrosCorrigendum 1: 3.3.9.2.2, 3.6.4.1.1, 3.6.4.1.2, 6.3, and 10.10.4.1. This is the first corrigendum to IEEE Std 529-1980. It mak
39、es corrections to 3.3.9.2.2, 3.6.4.1.1, 3.6.4.1.2, 6.3, and 10.10.4.1. 8 Copyright 2017 IEEE. All rights reserved. Contents 3. Requirements 10 3.3 Performance . 10 3.6 Environmental Requirements 10 6. Notes . 10 6.3 Model Equation . 10 10. Test Procedures 11 10.10 Axis Alignment 11 9 Copyright 2017
40、IEEE. All rights reserved. IEEE Standard Supplement for Strapdown Applications to IEEE Standard Specification Format Guide and Test Procedure for Single-Degree-of-Freedom Rate-Integrating Gyros Corrigendum 1: 3.3.9.2.2, 3.6.4.1.1, 3.6.4.1.2, 6.3, and 10.10.4.1 NOTEThe editing instructions contained
41、in this corrigendum define how to merge the material contained therein into the existing base standard and its amendments to form the comprehensive standard. The editing instructions are shown in bold italic. Four editing instructions are used: change, delete, insert, and replace. Change is used to
42、make corrections in existing text or tables. The editing instruction specifies the location of the change and describes what is being changed by using strikethrough (to remove old material) and underscore (to add new material). Delete removes existing material. Insert adds new material without distu
43、rbing the existing material. Insertions may require renumbering. If so, renumbering instructions are given in the editing instruction. Replace is used to make changes in figures or equations by removing the existing figure or equation and replacing it with a new one. Editing instructions, change markings, and this NOTE will not be carried over into future editions because the changes will be incorporated into the base standard.