欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ANSI FCI 70-2-2013 Control Valve Seat Leakage《控制阀门座泄漏》.pdf

    • 资源ID:434777       资源大小:45.48KB        全文页数:9页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ANSI FCI 70-2-2013 Control Valve Seat Leakage《控制阀门座泄漏》.pdf

    1、 ANSI/FCI 70-2-2013 AMERICAN NATIONAL STANDARD CONTROL VALVE SEAT LEAKAGE Fluid Controls Institute, Inc. Sponsor: Fluid Controls Institute, Inc. 1300 Sumner Ave Cleveland, Ohio 44115-2851 iiANSI/FCI 70-2-2013 AMERICAN NATIONAL STANDARD Control Valve Seat Leakage Sponsor Fluid Controls Institute, Inc

    2、. AmericanNationalStandardAmerican National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard

    3、does not in any respect preclude anyone, whether he has approved the standard or not, from manufacturing, marketing, purchasing or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the

    4、 latest editions. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Pu

    5、rchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Sponsored and published by: FLUID CONTROLS INSTITUTE, INC. 1300 Sumner Avenue Cleveland, OH 44115-2851 Phn: 216/241-7333 Fax: 216/241-0105 E-Mail:

    6、 fcifluidcontrolsinstitute.org URL: www.fluidcontrolsinstitute.org Copyright 2013, 2006, 1998, 1968 by Fluid Controls Institute, Inc. All Rights Reserved No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of

    7、 the publisher. Suggestions for improvement of this standard will be welcome. They should be sent to the Fluid Controls Institute, Inc. Printed in the United States of America iiiivCONTENTS PAGE Foreword v 1. Purpose 1 2. Scope and Limitations 1 3. Definitions . 1 4. Leakage Specifications and Class

    8、es 1-2 5. Test Procedures 2-4 6. References 4 Tables Table 1 2 Table 2 3 vForeword (This foreword is included for information only and is not part of ANSI/FCI 70-2-2013, Control Valve Seat Leakage.) This voluntary standard has been compiled and issued in the public interest. It is intended to elimin

    9、ate present misunderstandings and to assist and guide those people involved in the specification, use or manufacture of control valves. This standard, formerly known as ASME B16.104, was originally adopted on November 24, 1970 as FCI 70-2. The standard has been revised several times through the year

    10、s to stay current as the industry and its products have evolved and advanced. The standard was revised by the FCI Control Valve Section in 1998 in order to maintain consistency with the appropriate IEC Standards (IEC 534-4, currently IEC 60534-4). The standard was revised in 2003 to add the option t

    11、o permit low pressure gas testing to determine Class V leakage. During the canvass of the 2003 version, one respondent asked for the standard to be modified to specifically exclude on/off valves used for tight shut-off. The FCI Control Valve and Regulator Section notes that FCI 70-2 has been intende

    12、d to apply to control valve seat leakage. If line isolation and/or absolute tight shut-off is a normal expectation of the valve application, the FCI Control Valve and Regulator Sections recommend specifying another standard, such as API 598, “Valve Test and Inspection.” The 2013 revision consisted o

    13、f clarifications and editorial changes. The existence of a Fluid Controls Institute (FCI) standard does not in any respect preclude any member or non-member from manufacturing or selling products not conforming to this standard nor is the FCI responsible for its use. FCI recognizes the need to perio

    14、dically review and update this standard. Suggestions for improvement should be forwarded to the Fluid Controls Institute, Inc., 1300 Sumner Avenue, Cleveland, Ohio, 44115-2851. All constructive suggestions for expansion and revision of this standard are welcome. 1ANSI/FCI 70-2-2013 AMERICAN NATIONAL

    15、 STANDARD Control Valve Seat Leakage 1. PURPOSE 1.1 This standard establishes a series of seat leakage classes for control valves and defines production test procedures. 2. SCOPE & LIMITATIONS 2.1 Selection of a leakage class is not restricted as to valve design, but acceptable values for various co

    16、mmercially available designs are suggested for each class under Section 4. 2.2 This standard applies to production tests and cannot be used as a basis for predicting leakage at conditions other than those specified and does not apply to valves with a Cvvalue less than 0.1. 2.3 This standard is simil

    17、ar to IEC 60534-4, except that no provision is made for Class IV-S1. 3. DEFINITIONS 3.1 Control Valve 3.1.1 A valve with a power positioning actuator for moving a closure member to any position relative to a valve seat or seats in response to and in proportion to an external signal. The energy for a

    18、 control valve actuator is derived from an independent source. 3.1.2 Control valve body subassemblies on which an actuator is to be mounted at some later date are within the intent of this definition. 3.2 Cv- An experimentally determined valve sizing coefficient. (Ref. ISA S75.01 and ISA S75.02). 3.

    19、3 Rated Valve Capacity. The quantity of test fluid (air or water) that would pass through the valve at rated travel under the stated pressure conditions as determined by the appropriate equations and manufacturers ratings. 3.4 Rated Travel. The valve travel at which the manufacturers rating is estab

    20、lished. 3.5 Seat Leakage. The quantity of test fluid passing through an assembled valve in the closed position under the test conditions as defined. 3.6 Nominal Seat Diameter. Basic diameter used to determine maximum allowable seat leakage (Leakage Classes V and VI). This is also referred to as port

    21、 diameter or orifice diameter (of the seat ring). It should be noted that this is not the same as NPS. 4. LEAKAGE SPECIFICATIONS & CLASSES 4.1 The maximum allowable seat leakage as specified for each class shall not exceed the seat leakage in Table 1 or Table 2 using the test procedure as defined in

    22、 Section 5. For Classes II through VI each and every valve shall be tested. 4.2 Leakage Classes 4.2.1 CLASS I. A modification of any Class II, III or IV valve where design intent is the same as the basic class, but by agreement between user and supplier, no test is required. 4.2.2 CLASS II. This cla

    23、ss establishes the maximum permissible leakage generally associated with commercial double-seat control valves or balanced single-seat control valves with a piston ring seal and metal-to-metal seats. Use test procedure Type A. 4.2.3 CLASS III. This class establishes the maximum permissible leakage g

    24、enerally associated with Class II (4.2.2), but with a higher degree of seat and seal tightness. Use test procedure Type A. 4.2.4 CLASS IV. This class establishes the maximum permissible leakage generally associated with commercial unbalanced single-seat control valves and balanced single-seat contro

    25、l valves with extra tight piston rings or other sealing means and metal-to-metal seats. Use test procedure Type A. 4.2.5 CLASS V. This class is usually specified for critical applications where the control valve may be required to be closed, without a blocking valve. This class is generally associat

    26、ed with metal seat, unbalanced single-seat control valves or balanced single-seat designs with exceptional seat and seal tightness. Use test procedure Type B using water at the maximum operating differential pressure or Type B1 by using air at the specified conditions. 2TABLE 1 Leakage Class Maximum

    27、 Seat Leakage Test Procedure Class I (See 4.2.1) See Paragraph 4.2.1 None Class II (See 4.2.2) 0.5% of rated valve capacity Type A (See 5.1) Class III (See 4.2.3) 0.1% of rated valve capacity Type A (See 5.1) Class IV (See 4.2.4) 0.01% of rated valve capacity Type A (See 5.1) Class V (See 4.2.5) 5 x

    28、 10-4ml per minute of water per inch of seat diameter per psi differential Type B (See 5.2) 5 x 10-12 m3per second of water per mm of seat diameter per bar differential Type B (See 5.2) 4.7 standard ml per minute of air per inch of seat diameter Type B1 (See 5.3) 11.1 x 10-6standard m3per hour of ai

    29、r per mm of seat diameter Type B1 (See 5.3) Class VI (See 4.2.6) Leakage per Paragraph 5.4.4 as specified in Table 2 Type C (See 5.4) 4.2.6 CLASS VI. This class establishes the maximum permissible seat leakage generally associated with resilient seating control valves either unbalanced or balanced s

    30、ingle-seat with “O“ rings or similar gapless seals. Use test procedure Type C. 5. TEST PROCEDURES Warning: Provisions should be made to avoid over pressuring of measuring devices resulting from inadvertent opening of the valve plug. The following production tests may be conducted under ambient condi

    31、tions. Pressure inputs and leakage flow rate measurements shall be accurate to +/- 10 percent of reading. 5.1 Test Procedure Type A 5.1.1 Test medium shall be clean air or water at 10-51C (50-125F). 5.1.2 Pressure of test medium shall be 3-4 barg (45-60 psig) or within +/- 5 percent of the maximum o

    32、perating differential pressure, whichever is less. 5.1.3 The test fluid shall be applied to the normal or specified valve body inlet. The valve body outlet may be open to atmosphere or connected to a low headloss measuring device. 5.1.4 The actuator shall be adjusted to meet the operating conditions

    33、 specified. The full normal closing thrust as applied by air pressure, a spring, or other means shall then be applied. No allowance or adjustment shall be made to compensate for any increase in seat load obtained when the test differential is less than the maximum valve operating differential pressu

    34、re. 5.1.5 On valve body assemblies made for stock, tested without the actuator, a test fixture should be utilized which applies a net seat load not exceeding the manufacturers normal expected load under maximum service conditions. 5.1.6 On water test, care shall be taken to eliminate air pockets in

    35、the valve body and piping. 5.1.7 The leakage rate thus obtained can then be compared to the calculated values for Classes II, III and IV. See Table 1. 5.2 Test Procedure Type B 5.2.1 Test fluid shall be clean water at 10-52C (50-125F).35.2.2 The water test differential pressure shall be within +/- 5

    36、 percent of the maximum service pressure drop across the valve plug, not exceeding the maximum operating pressure at room temperature as determined by ANSI B16.1, B16.5, or B16.34, or some lesser pressure by individual agreement. 5.2.3 The fluid shall be applied to the normal specified inlet of the

    37、valve body. The valve plug shall be opened and the valve body assembly filled completely with water, including outlet portion and any downstream connecting piping, and then stroked closed. 5.2.4 The water test differential pressure as specified in 5.2.2 is then applied with the actuator adjusted to

    38、meet the operating conditions specified. The net actuator thrust shall be the specified maximum. Net actuator thrust above the specified maximum is not to be used. 5.2.5 When leakage flow is stabilized, the quantity should be observed over a period of time sufficient to obtain the accuracy under par

    39、agraph 5. 5.2.6 The leakage rate thus obtained shall not be greater than the value calculated from the definition of maximum seat leakage for Class V as shown in Table 1. 5.3 Test Procedure Type B1 5.3.1 Test medium shall be clean air or nitrogen gas at 10-52C (50-125F). 5.3.2 Inlet pressure of test

    40、 medium shall be 3.5 barg, (50 psig). 5.3.3 The test fluid shall be applied to the normal or specified valve body inlet, and the outlet connected to a suitable measuring device. 5.3.4 The leakage rate thus obtained shall not be greater than the value calculated from the definition of maximum seat le

    41、akage for Class V as shown in Table 1. TABLE 2 Class V INominal Seat Diameter (See 3.6)* Maximum Seat Leakage Millimeters (Inches) ml per Minute Bubbles per Minute* 25 ( 1) 0.15 1 38 (1.5) 0.30 2 51 (2) 0.45 3 64 (2.5) 0.60 4 76 (3) 0.90 6 102 (4) 1.70 11 152 (6) 4.00 27 203 (8) 6.75 45 250 (10) 11.

    42、1 - 300 (12) 16.0 - 350 (14) 21.6 - 400 (16) 28.4 - *Bubbles per minute as tabulated are a suggested alternative based on a suitable calibrated measuring device, in this case, a 6 mm (0.25 inch) O.D. x 1 mm (0.032 inch) wall tube submerged in water to a depth of from 3 to 6 mm (0.125 to 0.25 inch).

    43、The tube end shall be cut square and smooth with no chamfers or burrs and the tube axis shall be perpendicular to the surface of the water. Other apparatus may be constructed and the number of bubbles per minute may differ from those shown as long as they correctly indicate the flow in ml per minute

    44、. *If the valve seat diameter differs by more than 2 mm (0.08 inch) from one of the values listed, the leakage rate may be obtained by interpolation assuming that the leakage rate varies as the square of the seat diameter. 45.4 Test Procedure Type C - Class VI 5.4.1 Test medium shall be air or nitro

    45、gen gas at 10-52C (50-125F). 5.4.2 Pressure of the test medium shall be the maximum rated differential pressure across the valve plug or 3.5 bar (50 psig) whichever is the least. 5.4.3 The test fluid shall be applied to the normal or specified valve body inlet, and the outlet connected to a suitable

    46、 measuring device. 5.4.4 With the control valve adjusted to meet the operating conditions specified (see paragraphs 5.1.5 and 5.1.6) and with sufficient time allowance for stabilizing flow, the leak rate shall not exceed the values in Table 2. 6. REFERENCES 6.1 “International Electrical Commission (IEC) Standard 60534-4, Industrial Process Control Valves Inspection and Routine Testing.”


    注意事项

    本文(ANSI FCI 70-2-2013 Control Valve Seat Leakage《控制阀门座泄漏》.pdf)为本站会员(wealthynice100)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开