欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AIR FORCE MIL-M-43968 A-1985 MATTRESS PNEUMATIC (INSULATED)《(隔热)气压床垫》.pdf

    • 资源ID:428084       资源大小:1.16MB        全文页数:30页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AIR FORCE MIL-M-43968 A-1985 MATTRESS PNEUMATIC (INSULATED)《(隔热)气压床垫》.pdf

    1、MIL-M-43968A 12 Jul 85 SUPERSEDING MIL-M-43968 25 Jul 1977 MILITARY SPECIFICATION MATTRESS, PNEUMATIC, (INSULATED) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for one type of - p

    2、neumatic mattress in one size and two classes. 1.2 Classification. Pneumatic mattresses may be either of the following classes. Class 1 - Cemented seams, I - beam construction Class 2 - Molded seams, C - beam construction 2. APPLICABLE DOCUMENTS 2.1 Iusues of documents. The following documents of th

    3、e issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL V-L-6 1 V-T-2 9 5 PPP-B-6 36 PPP-T-45 Laces, Nylon. Thread, Nylon. Boxes, Shipping, Fiberboard. Tape, Gummed, Paper, Reinforced and Plain

    4、, for Sealing and Securing. MILITARY MIL-R-3065 Rubber, Fabricated Products. MIL-C-7350 Cloth, Parachute, Nylon. MIL-B-41826 Batting, Synthetic Fibers: Polyester, (Quilted and Unquilted, Beneficial comments (recommendations, additions, deletions) and any pertinent! data which may be of use in improv

    5、ing this document should be addressed to: the Engineering Division, San Antonio ALC/bllfEDO, Kelly AFB, Texas 78241 by using the self addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. “DISTRIBUTION STATEXVENT A. Approved for pu

    6、blic release; FSC 8465 distribution is unlimited.d THIS DOCUMENT CONTAINS 30 PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43659 MIL-1-45208 k _ - MIL-M-43768A 8i.I 7777906 0377692 5 MIL-M-43968A STANDARDS FEDERAL FED-STD-191 FED-STD-75

    7、 1 Stopper, Inflating Tube, Pneumatic Mattress. Inspection Systems Requirements. Textile Test Methods. Stitches, Seams, and Stitchings. MILITARY MIL-STD-105 MIL-STD-129 .MIL- S TD- 14 7 MIL-STD-417 Sampling Procedures and Tables for Inspection by Attributes. Marking for Shipment and Storage. Palleti

    8、zed Unit Loads for 40“ X 45“ Pallets. Classification System and Tests for Solid Elasto- meric Materials (Symbols and Tests). DRAWINGS U.S. ARMY NATICK RESEARCH AND DEVELOPMENT COMMAND 2-3-97 2-3-99 Mattress, Pneumatic; Construction Details. Mattress, Pneumatic; Inflating Tube and Stopper. (Figures 1

    9、 and 2 are miniature reproductions of the referenced drawings and are attached for information only.) (Copies of specifications, standards, drawings, and publications required - by contractors in connection with specific procurement functions should be obtained from the procuring activity or as dire

    10、cted by the contracting officer. ) 2.2 Other publications. The following documents form a part of this speci- fication to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. AMERICAN SOCIETY FOR TESTING AND

    11、MATERIALS ASTM D 903 Peel or Stripping Strength of Adhesive Bonds. * ASTM D 2000 Rubber Products in Automotive Application. (Application for copies should be addressed to the American Socie.ty for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 2 Provided by IHSNot for ResaleNo rep

    12、roduction or networking permitted without license from IHS-,-,-MIL-M-4368A 84 7777706 0377693 i i? MIL-M-43968A NATIONAL MOTOR FREIGHT TRAFFIG ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Asso- ciation, Inc., Traf

    13、fic Department, 1616 P Street, N.W., Washington, DC 20036.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606,) 3. Requirements 3.1 Materi

    14、al. 3.1.1 Base cloth. The base cloth shall be plain weave, white nylon cloth made from 70 denier (8 tex), multifilament, semi-dull, nylon yarn having sufficient twist or other yarn preparation to allow the cloth to meet both the base cloth and coated cloth.requirements. shall be heat set to prevent

    15、distortion, and shall conform to the physical and chemical requirements in table I when tested as specified in 4.3.1, As an al- ternate, nylon parachute cloth conforming to the weight, texture, and breaking strength requirements of type I of MIL-C-7350 may be used providing it meets all the other re

    16、quirements cited in table I herein. The cloth shall not be calendered, TABLE I, Base cloth requirements. Minimum Maximum n. n Weight, ounces per square yard Yarns per inch: - Warp - Filling - Warp - Filling - Warp - Filling - Warp - Filling Breaking strength, pounds: Tearing strength, pounds: Shrink

    17、age, percent: Chloroform-soluble material, percent PH viue Copper content, percent Manganese content, percent 2.0 (68 g/m) 106 (42 yards/cm) 92 (36 yarns/cm) 80 (356 N) 60 (267 N) 3.5 (16 N) 3.0 (13 N) - 5.0 - 2.3 (78 g/mL 2.0 1.5 1 .o 8.5 O .O03 0.0015 3 Provided by IHSNot for ResaleNo reproduction

    18、 or networking permitted without license from IHS-,-,-flIL-fl-439bA 4 Ba 7999906 0377b74 9 I! MIL-M-43968A 3.1.2 Coating compound. The compound used for coating the cloth shall be a heat-vulcanizable chloroprene synthetic rubber containing not less than 60 percent chloroprene by volume. The remainde

    19、r of the compound shall consist of softeners curing agents antioxidants pigments and reinforcing materials. 3.1.3 Coated cloth, 3.1.3.1 Top and bottom panels. The coating compound specified in 3.1.2 shall be applied to both sides of the base cloth in a quantity to meet the overa side side is to t 11

    20、 weight requirements in table II and shall be distributed so that one shall have 1 1/2 2 1/4 ouncespersquare yard (51 + 9 g/m2) and the other shall have the remainder. The coating on the heavily coated side, which be on the inside of the mattress shall be colored black throughout and I the surface c

    21、olor of the lightly coated side shall approximate Olive Green 207 (see 6.3). defects which may affect serviceability. a dull finish produced by an inert mineral dusting powder. ized coated cloth shall conform to the requirements in table II when tested as specified in 4.3.1. The coating shall be pro

    22、perly vulcanized and shall be free from The olive green surface shall have The fully vulcan- TABLE II. Properties of vulcanized coated cloth. Characterist ic Requirement Minimum Maximum Overall weight, ounces per square yard Breaking strength, pounds: - Warp - Filling Tearing strength, grams: - Warp

    23、 - Filling Hydrostatic resistance: - initial - After accelerated aging - After weatherometer - After strength of coating Adhesion, coating to cloth, pounds per 2 inch width - Heavily coated side - Lightly coated side 8.0 80 65 640 512 i/ i/ i/ u - 6.0 6.0 n (271 g/mL) 12.0 (356 N) - (289 N) - (6 N)

    24、(5 N) (27 N/51 mm) - (27 N/51 nun) - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-43968A 44 IM 999990b 0397695 O MIL-M-43 9 6 8A TABLE II. Properties of vulcanized coated cloth - Continued. Characterist ic Stiffness at 70F (2loC), warp, mm S

    25、tiffness at -40F (-40C), warp, mm Abrasion (olive green side only), 20 cycles Blocking, 220F (104OC), 30 minutes, scale rating Resistance to cold crack at -50F (-46OC) Resistance to accelerated a i inimum Maximum 80 120 - No. 1 i/ There shall be no leakage. - - 21 Visible loose fibers of the base cl

    26、oth shall not be exposed in the center 1 inch (25 mm) on the abraded portion. regarded as fibers from the yarns used to weave the base cloth and not as entire yarns or yarn plies. Visible loose fibers shall be - 31 There shall be no cracking, flaking, or peeling of the coating. - 41 Specimen shall n

    27、ot become stiff and brittle, nor soft and tacky, when compared to an unexposed specimen of the same sample unit. 3.1.3.2 Beam material. Coated cloth for beams may be that specified in 3.1.3.1 or may be the same base cloth coated on one side with black coating compound specified in 3.1.2. The single

    28、coated cloth shall be properly vulcanized, shall have an overall weight between 6.5 and 8.5 ounces per square yard (220 and 290 g/m2) and shall conform to the requirements for adhesion of coating to cloth as specified in table II, The beam material shall be tested as specified in 4.3.1. 3.1.3.3 Hing

    29、e material. Coated cloth for hinges used for reinforcing the fin edge of mattresses having the I-beam construction shall be the base cloth specified in 3.1.1, coated on one side with not less than 2.0 ounces per square yard (68 g/m2) of the coating compound specified in 3.1.2. A light coating of a s

    30、uitable rubber compound may be applied to the reverse side of the cloth, if desired, as a matter of convenience in assembly of the mattress. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-M-439bA 4 I 9999906 0397696 2 MIL-M-43968A 3.1.4 Ceme

    31、nt. The compound use for cementing shall be synthetic or natural rubber cement, completely compatible with the coating on the cloth and shall have all other characteristics equal to the requirements for the coatings. The cement shall be such that the cementing of the batting meets the requirements i

    32、n 3.3.3, the mattress meets the inflation test requirements in 3.4, and the beams and seams meet the adhesion requirements in 3.9. e 3.1.4.1 Cement for bonding inflating tube. The cement shall be a natural or synthetic rubber cement, similar in composition to the coating compound and when tested as

    33、specified in 4.3.1 shall have a minimum peel strength of 4.0 pounds per inch of width (70 N/mm of width). 9 3.1.5 Thread. The thread shall be nylon thread, type I or II, class 1 or 2, size By natural col-or or type III, size By natural color conforming to V-T-295. * 3.1.6 Inflating tube and stopper.

    34、 The inflating tube shall be made of black rubber material meeting the requirements of type, class, grade AA615 or BC615 of MIL-R-3065 and ASTM D-2000. The tube shall be of the size and design shown in drawing 2-3-99. The stopper shall conform to MIL-S-43659. 3.1.7 Braid, nylon. The round braid shal

    35、l conform to type II, class 1 of V-L-61 except that the ends shall have a plastic tip 1/2 inch (13 mm) in length (minimum) to prevent raveling. (305 - + 13 mm) long and shall be dyed black. The braid shall be 12 - + 1/2 inches 3.1.8 Batting, polyester. The polyester batting shall conform to the requ

    36、irements for type III of MIL-B-41826 except the batting shall weigh not less than 5.0 (170 g/m2) nor more than 5.5 ounces per square yard (186 g/m2) and shall have a minimum thickness of 0.730 inches (18.5 mm). All launder- ability requirements shall not be applicable. 3.2 Design. The mattress shall

    37、 conform in all respects to the design and dimensions shown on drawing 2-3-97 except that the.insulating batting shall be included. Dimensions shall be measured in uninflated condition with tolerances of plus or minus 1/4 inch (6 mm) except where other tolerances are specified. upper or head end of

    38、the mattress in the air channel shown on drawing 2-3-97. The center of the inflating tube shall be located 4 + 1 inch (102 + 25 mm) from the head edge of the mattress. The inflating tbe shall not 6e cemented over any beam flange. The inflating tube shall be attached to the top panel at the 3.3 Const

    39、ruction. a. The mattress shall be constructed with one piece top and bottom panels of the coated cloth specified in 3.1.3.1, assembled with the heavily coated side of the cloth on the inside of the air chamber. b. A piece of batting specified in 3.1.8, 3-1/4 + 1/4 inches (83 + 6 mm) wide by 62 + 1 i

    40、nches long (1575 + 25 mm) shall be incorporated into each of the-four center channels zn. such a manner asu to finish 6 - + 1 inch (152 - + 25 mm) from each ,end of the mattress. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-C. d. e. f. g. h. MIL

    41、-M-43968A A piece of batting specified in 3.1.8, 5-3/4 + 1/4 inches (146 2 6 mm) wide by 62 + 1 inches long (1575 + 25 and the mating surface of the coated fabric shall .-_ - be cleaned to remove dusting powder and dirt. -. - The inflating tube shall be securely fastened by full cementing and vulcan

    42、izing by means of a press to the underside of the top mattress panel of the upper or head end of the mattress. The bottom mattress panel shall be protected by a circular adhered chafing patch made of either of the coated fabrics specified in 3.1,3.1 or 3.1.2.1 not less than 3 inches (76 mm) in diame

    43、ter firmly affixed to the inside bottom mattress panel opposite the tube protrusion. shall be clean and free from flash. The inflating tube The braid for securing the inflating tube stopper shall be inserted through the holes of the tube stem and stopper, each end looped around the hole and securely

    44、 tied. The braid shall be 12 + 1/2 inches (305 + 13 mm) in length and when attached to the stopper, the stopper shall hang not less than 4 (102 mm) not more than 5 inches (127 mm) from the inflating tube hole. Either I-beam (class 1) or C-beam (class-2) construction of the mattress may be employed.

    45、3.3.1 I-beam construction (class i). The fin edge and I-beam seams shall be cemented full width and rolled to secure good adhesion, The I-beams shall be constructed from two strips of either of the coated specified in 3.1.3-1 or 3.1.3.2, not less than 2 1/2 inches (64 mm) wide, secured to each other

    46、 by stitching or cementing. each ply shall adhere one to the other. shall be not less than 1 1/8 inches (29 mm). If plies are joined by two rows of stitching, seam type SSa-2 with six to eight stitches per inch (2.4 to 3.1 stitches/cm) and stitch type 401 and 301 conforming to FED-STD-751 shall be u

    47、sed. The rows of stitching shall be at least 5/8 inches (16 mm) from the edges of the strip to permit attaching a flange to the body material having arms at least 5/8 inch (16 mm) on both sides. The beginnings and ends of all stitching shall be backstitched or tacked for at least 1/2 inch (13 mm). A

    48、ll breaks in stitching shall be overstitched for at least 1 inch (25 mm). The distance between rows of stitching shall be not less than 1 i/8 inches (29 mm). If plies are joined by cementing, they shall be full-cemented not less than If cemented, the heavily coated sides of the cloth in The effectiv

    49、e height of the partition 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 1/8 inches (29 mm) wide along the center-line of the strips, leaving at least 5/8 inch (16 mm) along each edge for forming the flange top and bottom. The line of attachment of the arms to top and bottom panels shall be not less than 1/2 inch (13 mm) in width. cemented to the body of the mattre


    注意事项

    本文(AIR FORCE MIL-M-43968 A-1985 MATTRESS PNEUMATIC (INSULATED)《(隔热)气压床垫》.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开