1、NOT MEASUREMENTSENSITIVEMIL - DTL - 38807D17 September 2012SUPERSEDINGMIL - PRF - 38807C29 November 1996DET AIL SPECIFICA TIONTECHNICAL MANUALS - ILLUSTRA TED P AR TSBREAKDOWNThis specification is approved for use by the Department of the Air Force and is availablefor use by all Departments and Agen
2、cies of the Department of Defense.Comments, suggestions, or questions on this document should be addressed toAFLCMC/HIA T echnical Data Section, 4170 Hebble Creek Road, Bldg. 280, Door 15,Area A, W right - Patterson AFB, OH 454335653 or emailed to SGMLsupportwpafb.af.mil.Since contact information ca
3、n change, the currency of this address information should beverified using the ASSIST Online database at https:/assist.dla.mil/.AMSC 9257 AREA TMSSDISTRIBUTION ST A TEMENT A. Appr oved for public r elease; distribution isunlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted
4、without license from IHS-,-,-MIL - DTL - 38807D1 SCOPE1.1 S c o p e . This specification covers the requirements for the preparation of Illustrated Parts Breakdown(IPB) T echnical Manuals (TM). The TMs are to be prepared in single or subdivided format, or as achapter of a maintenance/operation or ov
5、erhaul manual, as specified by the acquiring activity (see 6.2 b. ).Thisspecification provides for electronic delivery of data through use of the Document T ype Definition(DTD) prescribed in paragraph A.1 of Appendix A.1.2 D e t a i l . The level of detail contained in this detail specification is n
6、ecessary to comply with therequirements of the Joint Computer aided Acquisition and Logistics Support (JCALS) system.2 APPLICABLE DOCUMENTS2.1 G e n e r a l . The documents listed in this section are specified in sections 3 , and 4 of this specification.This section does not include documents cited
7、in other sections of this specification or recommended foradditional information or as examples. While every ef fort has been made to ensure the completeness of thislist, document users are cautioned that they must meet all specified requirements of documents cited insections 3 and 4 of this specifi
8、cation, whether or not they are listed.2.2 G o v e r n m e n t d o c u m e n t s .2.2.1 S p e c i fi c a t i o n s , s t a n d a r d s a n d h a n d b o o k s . The following specifications, standards, and handbooks forma part of this document to the extent specified herein. Unless otherwise specifi
9、ed, the issues of thesedocuments are those cited in the solicitation or contract(see 6.2 c. ).DEP AR TMENT OF DEFENSE SPECIFICA TIONSMIL - DTL - 87929 Detail Specification T echnical Manuals, Operation and MaintenanceInstructions in W ork Package Format (for USAF Equipment)DEP AR TMENT OF DEFENSE ST
10、 ANDARDSMIL - STD - 1808 Department of Defense Interface Standard System SubsystemSub - Subsystem NumberingMIL - STD - 38784 T echnical Manual General Style and Format Requirements(Copies of these documents are available online at https:/assist.dla.mil/quicksearch / or by mail from theStandardizatio
11、n Document Order Desk, 700 Robbins A venue, Building 4D, Philadelphia, P A 191 1 1 - 5094.)2.2.2 O t h e r G o v e r n m e n t d o c u m e n t s , d r a w i n g s a n d p u b l i c a t i o n s . The following other Government documents,drawings, and publications form a part of this document to the e
12、xtent specified herein. Unless otherwisespecified, the issues are those cited in the solicitation (see 6.2 d. ).PUBLICA TIONSFEDERAL LOGISTICS INFORMA TION SYSTEMDoD 4100.39 - M, H4/H8 Series Commercial and Government Entity Codes(Copies of these documents are available online at http:/www .dlis.dla
13、.mil search for CAGE.)AFMC INSTRUCTIONDODI 5330.03_AFI 33 - 395 DOCUMENT AUT OMA TION AND PRODUCTION SER VICE(DAPS)(Copies of these documents are available online at http:/www .e - publishing.af.mil (search AFI 33 - 395) orordered by mail from U.S. Government Printing Of fice Mail Stop: IDCC 732 N.
14、Capitol Street, NWW ashington, DC 20401.)AIR FORCE TECHNICAL MANUALST O 00 - 25 - 195 Source Maintenance and Recoverability Coding of Air ForceW eapons, Systems, and EquipmentT O 00 - 25 - 234 General Shop Practice Requirements for the Repair , Maintenance,and T est of Electrical Equipment(Obtain co
15、pies of all T echnical Orders from the ETIMS system as directed in T O 00 - 5 - 1 or contact yourProgram Management Of fice.)2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL - DTL - 38807D2.3 O r d e r o f p r e c e d e n c e . In the event of a
16、conflict between the text of this specification and the referencescited herein, the text of this document takes precedence. Nothing in this document, however , supersedesapplicable laws and regulations unless a specific exemption has been obtained.3 REQUIREMENTS3.1 P r e p a r a t i o n . The genera
17、l manner of preparation shall be in accordance with the requirements ofMIL - STD - 38784. The contractor shall use the DTD prescribed in paragraph A.1 of Appendix A forelectronic delivery of this manual (see 6.2 e. ).3.1.1 E l e c t r o n i c p r e s e n t a t i o n . Electronic presentation require
18、ments prescribed herein shall apply only to thedevelopment of T ype 1 linear data for electronic viewers. For development of Portable Document Format(PDF) data, print presentation requirements herein shall apply , as applicable.3.1.2 P r i n t p r e s e n t a t i o n . IPB manuals shall be prepared
19、in the 8.5 by 1 1 - inch size.3.2 M a n u a l l a y o u t . When the maintenance instructions for the equipment are in a single manual, the IPBshall also be in a separate single manual, except as specified in 3.2.1 and 3.2.2. All parts of the end itemshall be listed in accordance with the requiremen
20、ts found elsewhere in this specification, regardless of thelevel of coverage (or ganizational, intermediate, or depot) of the associated maintenance manual(s).3.2.1 C o m b i n e d m a n u a l s . When specified (see 6.2 f. ), the IPB shall be included in the maintenanceinstructions manual as the la
21、st chapter or last W ork Package (WP) and numbered in accordance withMIL - DTL - 87929 (MIL - STD - 38784 for legacey). However , if dif ference data sheets are to be included, theIPB shall precede them. The Chapter 1 material shall be included in the manual foreword or , whenusing MIL - DTL - 87929
22、 format, in the IPB WP foreword. The Chapter 3 and 4 material shall follow theMaintenance Parts List (MPL).Electronic presentation: Page count restrictions do not apply .Print presentation: Combined manuals shall not exceed 800 page units (including foldouts).3.2.2 S u b d i v i d e d m a n u a l .
23、When specified (see 6.2 g. ), the IPB manual MPL chapter shall be subdivided tofollow the chapter or WP structure of the maintenance manuals. Each subdivision shall be assigned aseparate T echnical Order number , for example, 1X - XX - 4 - 1, 1X - XX - 4 - 2, 1X - XX - 4 - 3, etc.Electronic presenta
24、tion: Page count restrictions do not apply .Print presentation: Chapters 1, 3, and 4 shall be combined in the first TM if it will not cause the manual toexceed 800 pages. The sequence shall be Foreword, Numerical Index, and Reference Designation Index. Ifcombining chapters would cause the first TM t
25、o exceed 800 pages, Chapter 1 shall be included in thefirst TM and Chapters 3 and 4 in the last TM.3.3 A r r a n g e m e n t . The manual shall contain as applicable:Front MatterChapter 1 - ForewordChapter 2 - Maintenance Parts ListChapter 3 - Numerical IndexChapter 4 - Reference Designator Index an
26、d System Subsystem Sub - subsystem Number (SSSN)Index if used3.4 F r o n t m a t t e r . Front matter shall be prepared in accordance with the requirements of MIL - STD - 38784with the following exceptions:3.4.1 T a b l e o f c o n t e n t s . The illustrations shall be listed by title in alphabetic
27、al order . When portions of anIPB are divided into groups, systems, etc., illustration titles shall be listed below group, system, etc.,titles. For combined manuals, the illustrations shall be listed in the manual s list of illustrations, if used.Otherwise, they shall be listed as previously describ
28、ed.Electronic presentation: T OC entries shall be linked to the text which they apply .3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL - DTL - 38807DPrint presentation: In lieu of a separate list of illustrations, illustration titles shall be a
29、part of the T able ofContents. Under the “Chapter 2 Maintenance Parts List“ heading in the T able of Contents, the title ofeach illustration and its appropriate page number shall be shown.3.4.2 F o r e w o r d . Foreword/preface/introduction requirements of MIL - STD - 38784 shall be contained inCha
30、pter 1, Foreword.3.4.2.1 L i s t o f r e l a t e d p u b l i c a t i o n s ( L R P ) . In addition to the requirements of MIL - STD - 38784, separateIPB manuals for accessories, components, assemblies, vendor items, etc., shall be listed. The list shallinclude the part number and listed in alphanume
31、ric sequence by part number . Model or type numbershall be used when no part number has been assigned. If applicable, the publication number and titlefor a power package buildup manual with IPB shall also be listed.Electronic print requirement: LRP entries shall be linked to the books which they app
32、ly when applicable.3.5 C h a p t e r 1 , F o r e w o r d . Chapter 1 shall contain the following:3.5.1 M o d e l ( s ) c o v e r e d . A listing of the models, types, configurations, modifications, task numbers, andseries or blocks of the end item covered by the manual.3.5.2 S e r i a l i z a t i o
33、n . The serialization table, when required by the acquiring activity , shall be used tospecify “Useable On“ codes (see 6.2 h. ).3.5.3 F i n d i n g p a r t n u m b e r s , i l l u s t r a t i o n , d e s c r i p t i o n .Electronic presentation requirement: An illustrated explanation (see figure 1 )
34、 shall be included whenMPL contains at least 200 part numbers.Print presentation requirement: When the MPL exceeds 16 pages, an illustrated explanation (see figure 1 )shall be included to describe:a. How to find a part number or description using the T able of Contents and illustration titles.b. How
35、 to find the illustration or description if a part number or reference designator is known.3.5.4 L i s t i n g o f s i m i l a r a s s e m b l i e s . An explanation of the method used to list parts of similar assembliesshall be included (see 3.6.9.7 ).3.5.5 P a r t s i n k i t s o r q u i c k c h a
36、 n g e u n i t s . When repair parts are supplied in the form of kits or quick changeunits, an explanation shall be included, and shall include information on determining what parts are included.3.5.6 S y m b o l s . An explanation of the dash ( -) (see 3.6.7.1.4 ), number sign (#) (see 3.6.9.2 and
37、3.6.10.3 ),asterisk (*) (see 3.6.9.9 ), and “F“ (see 3.7.2.2 ) symbols shall be included.3.5.7 S h e e t n u m b e r e x p l a n a t i o n . If multisheet illustrations are used, an explanation shall be includedthat the sheet number follows the index number and is separated with a slash (/) (see 3.6
38、.7.1 ). Theexplanation shall also state that, if an indexed item is on more than one sheet of an illustration, thefirst and last sheet numbers on which the item appears are given.3.5.8 U s e a b l e o n c o d e s . Definitions of the useable on codes used in the MPL of the manual shall beprovided. A
39、n explanation that codes are omitted for assemblies and parts installed in all configurations ofthe end items covered in the manual shall be included. Codes shown shall not be limited to the initialproduction configuration of a part or assembly .3.5.9 S o u r c e , M a i n t e n a n c e , a n d R e
40、c o v e r a b i l i t y ( S M R ) c o d e s . The following statement shall be included:“This manual contains Joint Military Service Uniform Source, Maintenance, and Recoverability (SMR)codes. Definitions of these SMR codes are available in T O 00 - 25 - 195.“3.5.10 N u c l e a r h a r d n e s s . I
41、f equipment covered has nuclear survivability requirements (for example,Over Pressure and Burst, Thermal Radiation, Electromagnetic Pulse, or T ransient Radiation Ef fects onElectronics), all Hardness Critical Items (HCI) shall be marked with . Unless otherwise specified bythe acquiring activity , a
42、ll HCIs shall be marked with the symbol immediately preceding the descriptionof the item (see 3.6.7.4.1 ). When approved by the acquiring activity , the symbol *HCI* may beused in lieu of the boxed HCI symbol (see 6.2 i. ).4Provided by IHSNot for ResaleNo reproduction or networking permitted without
43、 license from IHS-,-,-MIL - DTL - 38807D3.5.10.1 N u c l e a r h a r d n e s s s y m b o l e x p l a n a t i o n . Chapter 1 shall include a listing and explanation of the HCIsymbol and other pertinent information, as necessary , to emphasize the uniqueness of hardness features. Thisshall include an
44、 explanation that the HCI symbol establishes special requirements limiting changes andsubstitutions, and that the specific parts listed must be used to ensure hardness is not degraded. Thisstatement shall be preceded by a CAUTION heading. All changes to, or proposed substitutions of, HCIsmust be app
45、roved by the acquiring activity (see 6.2 j. ).3.5.1 1 E l e c t r o s t a t i c D i s c h a r g e S e n s i t i v e ( E S D S ) p a r t s . If equipment covered contains ESDS parts, theyshall be marked as shown in T O 0025234 (see figure 8 ). Unless otherwise specified by the acquiringactivity , all
46、 ESDS parts shall be marked with the ESDS symbol immediately preceding the descriptionof the item (see 3.6.7.4 a. ). When approved by the acquiring activity , the symbol *ESD* may beused in lieu of the ESDS symbol (see 6.2 k. ).3.5.1 1.1 E S D S s y m b o l e x p l a n a t i o n . Chapter 1 shall in
47、clude a listing and explanation of the ESDSsymbol: Other pertinent information shall be included as necessary to emphasize the uniqueness of ESDSparts. This shall include an explanation that the ESDS symbol requires that all ESDS parts be handledin accordance with the ESDS device handling procedures
48、 in T O 00 - 25 - 234. This explanation shallbe preceded by a CAUTION heading.3.5.12 P a r t s s t a n d a r d i z a t i o n . The following paragraph shall be included in the foreword chapter:“Parts Standardization. Authority for use of a part number dif ferent than the part number listed inthis IP
49、B is established by the Department of Defense (DoD) Interchangeability and Substitution(I the remaining space shall form thedescription column. Parts shall be listed to show parts relationship and in the sequence of disassembly ,except where that sequence cannot be maintained.FIGUREwhen the same partappears more than once in an illustration, the same index number shall be assigned to all identical parts.3.6.7.1.2 I n d e x n u m b e r s f o r a t t a c h i n g p a r
