欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AGMA 11FTM18-2011 Longitudinal Tooth Contact Pattern Shift.pdf

    • 资源ID:422136       资源大小:495.60KB        全文页数:11页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AGMA 11FTM18-2011 Longitudinal Tooth Contact Pattern Shift.pdf

    1、11FTM18AGMA Technical PaperLongitudinal ToothContact Pattern ShiftBy J.B. Amendola,J.B. Amendola, III, andD. Yatzook, Artec MachineSystemsLongitudinal Tooth Contact Pattern ShiftJohn B. Amendola, John B. Amendola III, and Dereck Yatzook, Artec MachineSystemsThe statements and opinions contained here

    2、in are those of the author and should not be construed as anofficial action or opinion of the American Gear Manufacturers Association.AbstractAfter a period of operation high speed turbo gears may exhibit a change in the longitudinal tooth contactpatternreducingfullfacewidthcontactandtherebyincreasi

    3、ngtheriskoftoothdistressduetothedecreasedloaded area of the teeth.The phenomena may or may not occur. In some units the shift is more severe than others and has beenobservedincaseswherethereisaslittleas16,000hoursofoperation. Inothercasesthereisnoevidenceofanychangeforunitsinoperationformorethan170,

    4、000hours. Thisconditionhasbeenobservedprimarilyinhelical gears. All recorded observations have been with case carburized hardened and ground gear sets.This document describes the phenomena observed among some of many installed high speed gear units infield operation which have been inspected. The au

    5、thors have not found any written material describing thisbehavior and upon further investigation suggest a possible cause. Left unchecked and without correctiveaction, this occurrence may result in tooth breakage.Copyright 2011American Gear Manufacturers Association1001 N. Fairfax Street, 5thFloorAl

    6、exandria, Virginia 22314October 2011ISBN: 978-1-61481-017-93 11FTM18Longitudinal Tooth Contact Pattern ShiftJohn B. Amendola, John B. Amendola III, and Dereck Yatzook, Artec Machine SystemsIntroductionField inspection of high speed turbo gears after an undefined period of operation may exhibit a cha

    7、nge in themating contact pattern of the gear mesh.This has been observed on gear rotors with the following characteristics:S Gear elements which are case carburized and groundS Relatively large face widths (greater than 300 mm)S Pitch line velocities greater than 100 m/sS Modified leads accounting f

    8、or both mechanical deflections and thermal deformationS Operating hours with as little as 16,000 hrs and as much as 170,000 hrs.Lead corrections for high speed gearsetsEvery gearset is subject to torque, resulting in elastic deflection of the gear tooth parts as well as the entirerotor body. Individ

    9、ual teeth bend, thepinion andwheel bodiestwist, bend,and expandunder theeffect ofthetorque, load, and centrifugal forces; see Figure 1.Forhighspeedgearsetsthemechanicaldeflectionsdescribedhereinarecompoundedwithadditionalfactorswhich result in further deformation of the gear teeth:- Churning of the

    10、lube oil and frictional losses in the bearings cause the rotor bodies to heat up andconsequently expand.- Pumping action of the oil and air entering the gear mesh produces an increased asymmetricaltemperature gradient of the gear tooth along the length of the tooth flank resulting in added deformati

    11、on.Special consideration must be given to compensatefor thesemechanical deflectionsand thermaldistortionsso that the load across the gear face is uniformly distributed under normal operating conditions.Toothingmodificationforgearsetswithpitchlinevelocitiesgreaterthan100m/srequirecarefulconsideration

    12、of thermal distortion. The resulting thermal deformation, in addition to the mechanicaldeflections, requiresacompositeprofileandlongitudinalmodificationtoachieveproperloaddistributionunderoperatingconditions;see Figure 2 and Figure 3.Figure 1. Tooth contact patterns of a spur toothed pinion without

    13、longitudinal correction at rest(top) and with load with load (bottom) applied4 11FTM18Figure 2. Schematic of single helical toothing deflection with added parameter for thermaldeformation and the associated lead correctionFigure 3. Schematic of double helical toothing deflection with added parameter

    14、 for thermaldeformation and the associated lead correction5 11FTM18InvestigationsbyMartinagliawereperformedtoaccuratelydeterminetemperatureconditionsinahighspeedpinion, see Figure 4.The dimensional parameters of the rotor configuration define how the lead is modified. Its derivation isspecific for a

    15、 continuous single or double helix. Therefore, this dimension is largely dependent on theexperience gained by years of observation of the tooth bearing patterns at nominal loads leading to accumu-lated empirical values.Early observationsEvidence of a longitudinal tooth contact shift was first observ

    16、ed by Artec in the early 1990s. When firstobserved,itwasinitiallythoughttobetheresultofchangesinthefoundationorotherexternalinfluencesofthegear unit inducing a small misalignment in the mesh. However subsequent inspection(s) of thesame and/orotherinstallation(s)revealedacurious shiftof thecontact pa

    17、ttern. Sincethis observationdid notconsistentlymanifest itself when inspecting other installations, the cause of the phenomena remained questionable for anumberofyears. Whenacontactshiftwasobserved,oftentimesheavyvarnishingofthelubricantonthegearteethinthevicinityofthecontactfacewasnotedintheareaoft

    18、hehighesttemperaturegradient;seeFigure 5.This is also the area where the deepest correction is required; see Figure 6. The phenomena had beenobserved in both gear sets where the thermal corrections were nearly negligible as well as units withsignificant thermal corrections.Figure 4. Effect of pitch

    19、line velocity on tooth flank temperature, establishment of anasymmetrical speed/temperature gradient6 11FTM18Turbine side Compressor sideFigure 5. Varnish deposits on gear teethLoaded flanks - designFigure 6. Original toothing modification plan(Ordinate values intentionally omitted for proprietary r

    20、easons)7 11FTM18PhenomenaIn all cases upon inspection, the contact pattern on both the loaded and non-loaded flank exhibited a contactshift deviating from the originally designed tooth contact pattern. In some units the contact shift is moreseverethanothers. Ifleftunattended,thiscontactshiftoftheint

    21、endeddesignedcontactpatternmayprogressresultingineverincreasinglocallyhighloadedsegmentsoftherotorflankswhichmayeventuallyresultingearfailure.Case study - example installation verifying longitudinal contact shiftApplication: Driving: gas turbine (4,670 rpm)Driven: centrifugal compressor (2,926.5 rpm

    22、)c-c center distance = 580 mm (22.853 in)B face width = 500 mm (19.764 in) helix angle = 10 (single helical) pressure angle = 20- rotor material = carburizing alloy steelP power = 37,285 kW (50,000 hp)PLV pitch line velocity = 109 m/sm module = 9.25Observations in the field: Inspection after 12 year

    23、s and 105,000 hours of continuousoperation:Dynamic:After 105,000 hours the gearset showed no signs of tooth surface distress; i.e., scuffing, micropitting andvirtually no signs of pitting (a few pits were found on the dedendum of the pinion). Varnishing (on both pinionand wheel) was noted to be heav

    24、iest in the flank section with the deepest lead correction. However underobservation it was readily noted that the “dynamic” load clearly favored the turbine end, little or no loadappeared to have been transmitted over the first150 mm of tooth face nearest the compressor end.Static:Thetoothcontactpa

    25、tternoftheoldrotorspriortoremovalwasfoundtobeinverypoorconditionandwasnotinaccordance with the original manufacturers protocol. The tooth contact was found tobe heavyin thecentralleft portion of the tooth flank in a centralized area 100 175 mm from the pinion drive end of the flank. In thisregion co

    26、ntact was found to be symmetrical to the pitch line (that is, distributed evenly along the profile) withequal load sharing along the addendum and dedendum.Attempt to correct in the fieldIn this case the unloaded static tooth contact pattern of the drive flank was originally designed to be at the(NDE

    27、) compressor side of the mesh. After 12years ofcontinuous operationthis staticpattern shiftedtowardthe (DE) gas turbine side. Subsequently, the non-loaded tooth flank (originally designed with a unmodifiedstraight contact pattern) shifted toward the (NDE) compressor side.Anattemptwasmadetocorrectthe

    28、noloadstatictoothcontactinthefieldbyshiftingthestaticcontacttowardthe NDE of the pinion. Only a fractional improvement was realized even with a relatively large adjustment.Improved contact is only possible if the longitudinal correction was no longer in accordance with the originalspecification. Thi

    29、s had confirmed that the tooth form had become distorted with time.Onthisbasisadecision wasmade toreplace therotor setwith anunused spareset ofrotors. The newrotorswere installed and the no load tooth contact was recorded, and confirmed to be according to the originalconfigured protocol. An operatio

    30、nal check of new spare rotors (dynamic tooth contact) via the inspection8 11FTM18cover revealed full load tooth contact after the operation reached steady state conditions. The observedcontact was 100% consistent across the entire tooth flank.Confirmation of hypothesisTheoldpinionandgearwhichweretak

    31、enoutofservicewereplacedonaleadandprofilecheckingmachinetodetermine the as found lead and profile measurements. Figure 6 describes the original corrective values asmadeonthegearsetloadedtoothflankspriortooperation. Figure 7describestheasfoundloadedtoothflankmeasuredvalues. Comparisonofthesefiguresde

    32、monstratestoothflankexpansionwhichshiftedtheoriginalno load static contact pattern and provided obvious evidence of permanent deformation of the gear teeth.Permanent deformation was also evident on the non-loaded tooth flanks (back side). Figure 8 and Figure 9provideagraphicalcomparisonofeachrotorno

    33、n-loadedtoothflanksshowingtheamountofchangethattookplace for both the pinion and wheel.Figure 7. Loaded flank - design and as found(Ordinate values intentionally omitted for proprietary reasons)Figure 8. Pinion unloaded flank - design versus as found9 11FTM18Figure 9. Wheel unloaded flank - design v

    34、ersus actualThe expansion is remarkable insofar as it has a magnitude nearly 75% of the amount of the design leadmodification.Theory as to causeDuring gear unit operation thereis ahigh velocityaxial flowof lube,oil andair acrossthe helix(s)of themesh.Through mesh engagement, oil and air are mixed an

    35、d compressed resulting in an asymmetrical (uneven)tooth flank temperature gradient; see Figure 4.Inthecasestudyhighlylocalizedtemperatureshadreachedlevelsthatcausedametallurgicaltransformationwherein entrained austenite was transformed to martensite. This transformation resulted in an expansion ofth

    36、ecasematerialtherebyaffectingthe tooththickness whichresulted ina contactpattern changeon boththeloaded and non-loaded flanks. The mechanism of expansion is due to the density difference betweenausteniteandmartensite. AsnotedfromFigure 9thisexpansiondoesnotoccurinauniformmannersincethetemperature ri

    37、se from the meshing action is asymmetrical over the tooth length.Dudleys Handbook of Gear Design states: “After quenching, steels are usually tempered or stress-relieved.The tempering operation may be used to reduce the hardness of a part and increase the toughness. Byproperly adjusting the temperin

    38、g temperature hardness values can be obtained over a wide range. Evenwhennoreductioninhardnessisdesiredalow-temperature(250to350F)temperingoperationisdesirabletoreduce stresses in the steel and produce a kind of martensite that is tougher than the kind producedimmediately upon quenching.” This tempe

    39、rature range may be achievable in the operational environment ofsome running gear units.Load conditions, partial loads vs. full load, tooth module, level of operating stress numbers relative to geartoothdesignmayalsohavecontributinginfluences. Animproperdesignleadcorrectionand/ormanufacturingerrorso

    40、ftheunit,oranimproperlysetupgeartoothcontactpatternduringtheoriginalinstallation,orchangesdue to uneven bearing wear or soft foot may also contribute to the described phenomena.Considering the successfullength ofservice inthe notedexample itcan bedetermined withcertainty thatthegearset was furnished

    41、 with an optimized lead and at the outset of service the unit operated with uniform con-tact across the entire full face width of the toothing. As service time was accumulated a segmentof thetoothflankincreasedintemperatureandreachedthetemperingtemperaturerange. Thismostlikelywastheresultof accumula

    42、tedvarnish stainingof thegear teeth. Transformationoccurred slowlyat firstand thenincreasedat a faster rate reducing flank contact over time. The appearance of significant varnishing of the gear teethwas the cause of this rise in tooth temperature.10 11FTM18Varnishing does two bad things:S Varnish i

    43、s an insulator on the gear teeth thereby reducing the efficiency of the lube oil to cool the gearteeth. As the varnish builds up a worsening condition develops. As a result, the gear teeth will gethotterthereby encouraging tempering of the gear teeth in that regime of the flank.S Varnishing increase

    44、s the frictional affects of the compressed lube oil and air as it travels longitudinallyacross the flank thereby adding additional heat to the tooth flanks.Regardlessofthemeansofentrainment,theactionthatleadstovarnishisinplace. Fromhere,thefailurecanproceed with adiabatic compression in the load zon

    45、e of a lubricationsystem. Adiabatic compressionoccurswhen air bubbles travel from low pressure to high pressure. The air bubble compresses rapidly (implosion)resulting in intense entrapment of the heat and extreme rise in temperature.In this example during the earlier years of service prior to the s

    46、low development tooth varnishing, themaximum temperature along the tooth length was most likely below the tempering temperature range. Asvarnish began to deposit on the gear teeth, the temperature gradient increased and gradually entered thetempering temperature range beginning the process of transf

    47、orming retained austenite to martensite andthereby began its expansion. What was discovered finally was the result of what may have occurred over aperiod of operation not consistent in a linear sense with the running life of the gearset. In fact, the majortransformation period likely started quite s

    48、ometime after the start of service and then changed rapidly, mostlikely in the last few years of service. So while there has not been a failure, evidence of surface distress wasbeginning to develop with small pitting located on the dedendum of the pinion, a failure may have beenimminent and was caug

    49、ht in time. Inspection of the rotors revealed an increase in surface hardness of34Rc(original58-59Rcnow61-62Rc)asmeasuredatvariouspointsonseveralgear teeth. This is theresult of untempered martensite transformed from retained austenite. While the transformed surface isharderthantheearlierstartingconditionitcouldnotpossiblysustaintheloadoversuchanarrowportionoftheface for very much longer. Considering the locally high loads no additional surface distress was observedsuch as more pitting or scuffing. We attributed this to the improved surface condition over running t


    注意事项

    本文(AGMA 11FTM18-2011 Longitudinal Tooth Contact Pattern Shift.pdf)为本站会员(bonesoil321)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开