欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO TP 106-2013 Standard Method of Test for Determination of Heavy Metal Content of Glass Beads Using X-Ray Fluorescence (XRF).pdf

    • 资源ID:418378       资源大小:63.71KB        全文页数:5页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO TP 106-2013 Standard Method of Test for Determination of Heavy Metal Content of Glass Beads Using X-Ray Fluorescence (XRF).pdf

    1、Standard Method of Test for Determination of Heavy Metal Content of Glass Beads Using X-Ray Fluorescence (XRF) AASHTO Designation: TP 106-13 (2015)1American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-4c TP 106-1 AASHTO

    2、 Standard Method of Test for Determination of Heavy Metal Content of Glass Beads Using X-Ray Fluorescence (XRF) AASHTO Designation: TP 106-13 (2015)11. SCOPE 1.1. This test method covers the determination of the total heavy metal content of glass beads using X-ray fluorescence (XRF). Heavy metals in

    3、clude lead, antimony, and arsenic. 1.2. The values stated in SI units are to be regarded as the standard. 1.3. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety

    4、and health practices and determine the applicability of regulatory limitations prior to use. 2. REFERENCED DOCUMENTS 2.1. AASHTO Standard: M 247, Glass Beads Used in Pavement Markings 3. SUMMARY OF TEST METHOD 3.1. This test method is used to determine the total concentration of heavy metals using X

    5、RF testing. Testing may be performed with a Field Portable XRF (FP-XRF) or a laboratory XRF. 3.2. For an FP-XRF, the glass beads to be tested are placed in a loose state in a sample cup. 3.3. For a laboratory model XRF, the glass beads can be tested either in a loose state in a sample cup using a he

    6、lium flush or as a pressed pellet. Note 1If using a laboratory model XRF, testing the glass beads in a loose state using a helium flush is the preferred method. 4. SIGNIFICANCE AND USE 4.1. This method is designed to identify the presence and concentration of heavy metals in samples of glass beads.

    7、The method determines the total concentration and may be used to determine compliance with total concentration limits in M 247. 5. APPARATUS 5.1. XRF SpectrometerEither a field portable or a laboratory model XRF spectrometer may be used. If a laboratory model XRF spectrometer is used, it must be cap

    8、able of operating with the analysis chamber under vacuum or flushed by helium (see Note 1). 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4c TP 106-2 AASHTO 5.2. Sample CupIf the test includes using

    9、 an FP-XRF or with helium flush in a laboratory model XRF, use a thin-walled container to hold the loose glass beads. Sample cup includes a collar and cap. 5.3. Pressed Pellet PressIf the test includes using a vacuum in a laboratory model XRF, use a pressed pellet press to prepare the pressed pellet

    10、 for testing. 5.4. Mixer MillIf the test includes using a vacuum in a laboratory model XRF, use a mixer mill to pulverize and blend the glass bead sample with the binding agent to prepare the pressed pellet for testing. 6. MATERIALS 6.1. For loose samples prepared in samples of beads tested in a sam

    11、ple cup, polypropylene film, filter paper, and polyester fiber stuffing are needed. 6.1.1. FilmPolypropylene film. 6.1.2. Filter PaperFilter paper disk to fit over the sample. 6.1.3. Fiber StuffingPolyester fiber stuffing such as used for aquarium filter or pillow filling. 6.2. For pressed pellets,

    12、a binder is required to form the glass beads into a pellet. 6.2.1. BinderLow absorption wax or cellulose binding agent. 6.2.2. Aluminum CupsUsed as backing for the pressed pellet sample. 7. SAMPLING AND SAMPLE PREPARATION 7.1. SamplingTake a representative sample of the glass beads. Store the sample

    13、 in a container until ready for the test. 7.2. Sample Preparation of Loose Glass Beads in Sample CupIf the sample is to be tested using an FP-XRF or a laboratory model XRF with helium flush, the glass beads are tested in a sample cup. Use the following steps to prepare the sample: 7.2.1. Place polyp

    14、ropylene film on top of an XRF sample cup. The film goes on the end of the cup with the indented ring. 7.2.2. Secure the film with the collar. The flange inside the collar faces down and snaps into the indented ring of the cup. Inspect the installed film window for continuity and smooth, taut appear

    15、ance. 7.2.3. Place the sample cup on a flat surface with the film window-side down. Fill the cup with at least 5 g of glass beads. Place the beads in an even layer and lightly tamp into place. 7.2.4. Place a filter paper disk on the sample after tamping, then fill the cup with polyester fiber stuffi

    16、ng. Put the cap on the cup. 7.3. Sample Preparation of Pressed PelletIf the sample is to be tested using a laboratory model XRF with a vacuum chamber, the glass beads are tested as a pressed pellet. Use the following steps to prepare the sample: 2015 by the American Association of State Highway and

    17、Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4c TP 106-3 AASHTO 7.3.1. Combine 6.000 g of glass beads and 1.000 g of binding agent. 7.3.2. Using a mixer mill, pulverize and blend the glass beads and binding agent into a homogeneous sample for pressing

    18、. Note 2For large beads, mill for 710 min. For small beads, mill for 57 min, depending on the type of mixer mill used. 7.3.3. Place an aluminum cup with tapered walls into the bottom of the press die chamber. 7.3.4. Add the homogeneous sample to press pressing. Follow the manufacturer procedures for

    19、 the operation of the press. 7.3.5. Apply 25 tons of pressure for 4 min and use a 1-min release. 8. CALIBRATION AND STANDARDIZATION 8.1. XRF SpectrometerCalibrate or standardize the XRF spectrometer according to the manufacturers recommendations. 9. PROCEDURE 9.1. FP-XRFPlace the sample cup on a sta

    20、ble surface. Direct the FP-XRF at the sample cup and run according to the manufacturers recommendations using the standard soil analysis mode. Record the concentration of lead, antimony, and arsenic. 9.2. Laboratory Model XRF with Helium FlushPlace the sample cup in the XRF. Run according to the man

    21、ufacturers recommendations under helium gas conditions using a standard-less software program. Record the concentration of lead, antimony, and arsenic. 9.3. Laboratory Model XRF with VacuumPlace the pressed pellet in the XRF. Run according to the manufacturers recommendations under vacuum conditions

    22、 using a standard-less software program. Record the concentration of lead, antimony, and arsenic. 10. INTERPRETATION OF RESULTS 10.1. The XRF reports the elements detected in the sample and elements that are below the detection limit. For an element to be detected by your analyzer in a given sample,

    23、 the measured concentration of the sample must be at least three times the standard deviation of the measurement. This detection limit will depend on the composition of the sample. The measurement precision for each element displayed appears to the right of the measured concentration, under the head

    24、ing “”. The precision of each measurement is two times the standard deviation (). An element is classified as “detected” if the measured concentration (in ppm) is at least 1.5 times the precision. Detected elements are displayed in ppm, followed by the measurement precision. Nondetected elements are

    25、 shown as the detection limit (LOD) for that sample. The detection limit for a given element varies depending on the other elements in the matrix. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4c TP

    26、 106-4 AASHTO 11. REPORT 11.1. Report the following information: 11.1.1. Sample identification; 11.1.2. Manufacturer; 11.1.3. Batch or lot number (if applicable); 11.1.4. Location sampled; and 11.1.5. Concentration of lead, antimony, and arsenic (ppm). 12. PRECISION AND BIAS 12.1. PrecisionThe resea

    27、rch required to develop precision estimates has not been conducted. 12.2. BiasThe research required to establish the bias has not been conducted. 13. KEYWORDS 13.1. Glass beads; heavy metal; X-ray fluorescence; XRF. 1This provisional standard was first published in 2013. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.


    注意事项

    本文(AASHTO TP 106-2013 Standard Method of Test for Determination of Heavy Metal Content of Glass Beads Using X-Ray Fluorescence (XRF).pdf)为本站会员(王申宇)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开