欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO T 195-2011 Standard Method of Test for Determining Degree of Particle Coating of Asphalt Mixtures.pdf

    • 资源ID:418140       资源大小:42.98KB        全文页数:3页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO T 195-2011 Standard Method of Test for Determining Degree of Particle Coating of Asphalt Mixtures.pdf

    1、Standard Method of Test for Determining Degree of Particle Coating of Asphalt Mixtures AASHTO Designation: T 195-11 (2015) ASTM Designation: D2489/D2489M-08 American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-2c T 195-

    2、1 AASHTO Standard Method of Test for Determining Degree of Particle Coating of Asphalt Mixtures AASHTO Designation: T 195-11 (2015) ASTM Designation: D2489/D2489M-08 1. SCOPE 1.1. This method covers the determination of the degree of particle coating in an asphalt mix on the basis of the percentage

    3、of coarse aggregate particles that are completely coated. Determination of the percentage of coated particles for varying mixing times may be used to establish the least mixing time required to produce satisfactory coating of the aggregate for a given set of conditions. This test method applies to m

    4、ixtures containing aggregate of a nominal maximum aggregate size less than 38 mm (11/2in.). 1.2. The values stated in SI units are to be regarded as the standard. 2. REFERENCED DOCUMENTS 2.1. AASHTO Standards: M 92, Wire-Cloth Sieves for Testing Purposes T 168, Sampling Bituminous Paving Mixtures 3.

    5、 APPARATUS 3.1. Sieves9.5-mm (3/8-in.) and 4.75-mm (No. 4) sieves conforming to M 92. 3.2. StopwatchFor checking the actual mixing time. 3.3. ThermometerWith a range from 10 to 204.4C (50 to 400F). 3.4. Sample Shovel. 3.5. Sample Trays. 4. SAMPLING 4.1. Batch PlantPermit the plant to operate at an e

    6、stablished mixing time per batch (timed by a stopwatch). 4.2. Continuous PlantEstablish a mixing time by use of the following formula: ( )( )pug mill contents, kg lbpug mill output, kg s lb s(1) 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Dupli

    7、cation is a violation of applicable law.TS-2c T 195-2 AASHTO 4.3. Samples should be taken at the asphalt mixing plant, immediately after discharge from the pug mill, from three alternate truckloads of mixture (see T 168). 4.4. The amount of material required to perform the test is approximately 2.3

    8、to 3.6 kg (5 to 8 lb). 5. PROCEDURE 5.1. Sieve each material immediately, while it is still hot, on a 9.5-mm (3/8-in.) sieve for materials with a maximum size larger than 9.5 mm (3/8in.). For materials with a maximum size of 9.5 mm (3/8in.) or less, use a 4.75-mm (No. 4) sieve. Take a sample large e

    9、nough to yield between 200 and 500 coarse particles retained on the 9.5-mm (3/8-in.) or 4.75-mm (No. 4) sieve. Do not overload the sieves. If necessary, sieve the sample in two or three operations. Shaking should be reduced to a minimum to prevent recoating of uncoated particles. 5.2. Place the part

    10、icles on a clean surface in a one-particle layer, and start counting them immediately. 5.3. Very carefully examine each particle under direct sunlight, fluorescent light, or similar light conditions. If even a tiny speck of uncoated stone is noted, classify the particle as “partially uncoated.” If c

    11、ompletely coated, classify the particle as “completely coated.” 6. CALCULATION 6.1. The required computation is as follows: no. of completely coated particles 100percent of coated particlestotal no. of particles= (2) 7. REPORT 7.1. Report the following information: 7.1.1. Type of plantbatch or conti

    12、nuous; 7.1.2. Type of mix; 7.1.3. Mixing time to the nearest 0.5 min; 7.1.4. Mixing temperature to the nearest 5C (9F); and 7.1.5. Percent of coated particles to the nearest 0.1 percent. 8. PRECISION AND BIAS 8.1. PrecisionNo precision data are available at this time. 8.2. BiasBecause there are no a

    13、ccepted reference materials suitable for determining the bias of this test method, no statement of bias is presented. 9. KEYWORDS 9.1. Asphalt; asphalt mixing plant; coating; mixing time; pug mill. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.


    注意事项

    本文(AASHTO T 195-2011 Standard Method of Test for Determining Degree of Particle Coating of Asphalt Mixtures.pdf)为本站会员(hopesteam270)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开