欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    AASHTO R 72-2016 Standard Practice for Match Curing of Concrete Test Specimens.pdf

    • 资源ID:418027       资源大小:58.45KB        全文页数:5页
    • 资源格式: PDF        下载积分:2000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要2000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    AASHTO R 72-2016 Standard Practice for Match Curing of Concrete Test Specimens.pdf

    1、Standard Practice for Match Curing of Concrete Test Specimens AASHTO Designation: R 72-161 Release: Group 1 (April 2016) American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001 TS-3c R 72-1 AASHTO Standard Practice for Match

    2、Curing of Concrete Test Specimens AASHTO Designation: R 72-161Release: Group 1 (April 2016) 1. SCOPE 1.1. This recommended practice covers procedures for making and curing cylindrical concrete specimens at the same temperature as that measured in a concrete member. 1.2. The concrete sample used to m

    3、ake the specimens shall be taken from the concrete being placed in the same member where the temperature is to be measured. 1.3. This procedure can be deployed with confidence for both air chamber and insulated jacket (Surecure) systems and for both molded cylinders with nominal diameter to height d

    4、imensions of 100 by 200 mm (4 by 8 in.) or 150 by 300 mm (6 by 12 in.). However, users should be watchful of Type I error for air chamber systems and Type II error with insulated jacket mold systems. A Type I error represents the situation where loss of temperature control occurs over only a portion

    5、 of the entire match-cure duration where control is later regained. A Type II error represents the situation where a constant level of temperature control error occurs during the entire match-cure duration. 1.4. The values stated in SI units are to be regarded as the standard. 1.5. This standard doe

    6、s not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2. REFERENCED DOCUMENTS 2.1. AASHTO

    7、 Standards: M 205M/M 205, Molds for Forming Concrete Test Cylinders Vertically R 60, Sampling Freshly Mixed Concrete T 23, Making and Curing Concrete Test Specimens in the Field T 119M/T 119, Slump of Hydraulic Cement Concrete T 152, Air Content of Freshly Mixed Concrete by the Pressure Method T 196

    8、M/T 196, Air Content of Freshly Mixed Concrete by the Volumetric Method 2.2. ASTM Standards: C125, Standard Terminology Relating to Concrete and Concrete Aggregates C1064/C1064M, Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete 2016 by the American Association of State

    9、 Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-3c R 72-2 AASHTO 3. TERMINOLOGY 3.1. For definitions of terms used in this practice, refer to ASTM C125. 4. SIGNIFICANCE AND USE 4.1. This method provides a procedure for curing concrete cylind

    10、ers at the same temperature as that monitored at a specific location in a concrete member. Consequently, the compressive strength of the cylinder more accurately represents the in-place concrete strength of the member. The method is particularly useful for determining the concrete compressive streng

    11、th at early ages in the fabrication of precast concrete members or for determining the compressive strength of concrete at a critical location in a structural member. 5. APPARATUS 5.1. The apparatus shall consist of a monitoring and heating system capable of maintaining concrete cylinders at a tempe

    12、rature within 2C (4F) of the temperature of the concrete at a specific location in the member. A satisfactory system may include a temperature sensor in the member, a controller, special insulated cylinder molds with built-in heating systems, and a temperature sensor in the molds. 5.2. Temperature S

    13、ensor in the MemberTemperature sensors shall be placed at the most critical locations for strength development. The purchaser shall determine the critical locations for temperature sensors in each type of member and show the locations on the project drawings or the contractor shall submit drawings s

    14、howing proposed locations to the purchaser for approval. 5.2.1. Temperature sensor wire shall be durable enough to withstand the wear associated with construction operations and shall have a size of 20 awg or larger in diameter (Note 1). Note 1In locations where electrical interference may affect th

    15、e measured data, shielded wire should be used. 5.3. ControllerThe controller shall be capable of monitoring the temperatures of the member and cylinders and controlling the heating system to maintain the cylinder temperature within +2C (+4F) of the temperature measured in the member. Proper operatio

    16、n of the system shall be verified on a regular basis in accordance with the manufacturers recommendations. 5.4. Cylinder Molds: 5.4.1. Cylinder molds shall conform to the requirements of M 205M/M 205 for reusable molds and shall be fitted with watertight lids to prevent moisture loss. 5.4.2. Cylinde

    17、r molds shall have inside nominal diameter by height dimensions of 100 by 200 mm (4 by 8 in.) or 150 by 300 mm (6 by 12 in.). 5.4.3. When heated cylinder molds are used, they shall have built-in thermocouples that sense the temperature of the concrete specimens. Each cylinder mold shall have a heati

    18、ng element that surrounds the core of the mold, provides uniform heat to the concrete specimen, and is capable of maintaining a cylinder temperature that matches the temperature of the concrete member within the stated tolerance (Note 2). Note 2Because the match-curing system only provides heat to t

    19、he cylinder and cannot cool it, the temperature of the cylinder may exceed that of the member if the temperature of the member decreases at a greater rate than that of the cylinder. 2016 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a v

    20、iolation of applicable law.TS-3c R 72-3 AASHTO 6. TEST SPECIMENS 6.1. Test specimens shall be cylinders of concrete cast and hardened in an upright position, with a length equal to twice the diameter. When the nominal maximum size of coarse aggregate does not exceed 50 mm (2 in.), the cylinder may b

    21、e 150 by 300 mm (6 by 12 in.). When the nominal maximum size of coarse aggregate does not exceed 25 mm (1 in.), the cylinder may be 100 by 200 mm (4 by 8 in.). 6.2. A minimum of two 150-by-300-mm (6-by-12-in.) or three 100-by-200-mm (4-by-8-in.) cylinders shall be made for each strength test when th

    22、e specified strength does not exceed 34 MPa (5000 psi). A minimum of three cylinders shall be made for each strength test when the specified strength exceeds 34 MPa (5000 psi). 7. PROCEDURE 7.1. System InstallationPrior to concrete placement, the temperature sensors in the member shall be securely f

    23、ixed at the specified locations. The sensor tips shall be installed such that they do not have direct contact with steel reinforcement. Prior to concrete placement, proper operation of the match-curing system shall be verified in accordance with the manufacturers recommendations. 7.2. Sampling Concr

    24、eteThe samples used to fabricate test specimens under this standard shall be obtained in accordance with R 60 unless an alternative procedure has been approved. The concrete sample shall be taken from concrete placed as close as practical to the temperature sensor in the member. 7.3. Slump, Air Cont

    25、ent, and Temperature: 7.3.1. SlumpMeasure and record the slump of each batch of concrete from which specimens are made, immediately after remixing in the receptacle as required by T 119M/T 119. 7.3.2. Air ContentDetermine and record the air content in accordance with either T 152 or T 196M/T 196. Th

    26、e concrete used in performing the air content test shall not be used in fabricating test specimens. 7.3.3. TemperatureDetermine and record the concrete temperature in accordance with ASTM C1064/C1064M. 7.4. Molding SpecimensTest specimens shall be molded using the procedures of T 23. 7.5. Match Curi

    27、ng: 7.5.1. Covering after FinishingImmediately after finishing, precautions shall be taken to prevent evaporation and loss of water from the specimens. Cover specimens with a nonabsorbent, nonreactive plate or a sheet of impervious plastic. 7.5.2. Specimen StorageDuring match curing, molds and speci

    28、mens shall be shielded from direct rays of the sun, other heating devices, rain, and wind. All molds controlled by the same controller shall be stored together (Note 3). Note 3Because the match-curing system only provides heat to the cylinders, better temperature control is obtained when the cylinde

    29、rs are stored in an environment that is cooler than the temperature of the concrete in the member. 7.5.3. Connect the molds to the controller and match cure for the specified length of time. 2016 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplicati

    30、on is a violation of applicable law.TS-3c R 72-4 AASHTO 7.5.4. Following the match-curing period, the cylinders shall be removed from the molds and subsequently stored in a similar temperature and moisture environment as the member unless stated otherwise in the project specifications. 7.5.5. When m

    31、atch-cured cylinders are used to determine concrete release strengths, it is recommended that match curing be continued for as long as possible and until the cylinders are stripped for testing. 1Formerly AASHTO Provisional Standard PP 54. First published as a full standard in 2016. 2016 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.


    注意事项

    本文(AASHTO R 72-2016 Standard Practice for Match Curing of Concrete Test Specimens.pdf)为本站会员(feelhesitate105)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开